Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY › from 2012.10
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052458 AUTOMATIC TRANSMISSION ASSEMBLY A

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TRANSMISSION CONTROL CABLE BRACKET

a.

Install the control cable bracket with the 2 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 3.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C237875

Engage the spline of the input shaft turbine runner.


b.
C237876

Engage the spline of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft spline are difficult to engage with the stator splines, move the torque converter back approximately 10 mm (0.787 in.) and engage the splines while rotating the torque converter.



c.
C237877

Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.


d.

Clean the torque converter set bolt holes.


e.
C282305
3.229,1.844 3.385,2.042 0.156,0.198 10 false A

Using a vernier caliper and straightedge, measure dimension A between the transaxle contact surface of the engine and the torque converter contact surface of the drive plate.

NOTICE:

Make sure to deduct the thickness of the straightedge.



f.
D025545
2.948,1.823 3.198,2.083 0.25,0.26 10 B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

Standard:

B = A + 1.00 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the transaxle is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.




Hide 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C213730
1.563,1.083 2.698,1.083 true 2.76,0.99 3.094,1.25 0.333,0.26 10 *1 0.656,1.01 1.01,1.25 0.354,0.24 10 *2
*1 Torque Converter Centerpiece
*2 Crankshaft


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.

Clutch spline grease::

Toyota Genuine Clutch Spline Grease or equivalent

Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.

While keeping the engine and automatic transmission assembly horizontal, align the knock pins with the holes in the automatic transmission assembly and Install the 5 bolts.

Torque:
71 N*m (720 kgf*cm, 53 ft.*lbf)

NOTICE:
·

Confirm that the 2 knock pins are installed to the transaxle contact surface of the engine cylinder block before installing the automatic transmission assembly.

·

Do not forcibly pry on the automatic transmission assembly

·

Check that the torque converter rotates.




c.

Hold the crankshaft pulley bolt with a wrench and install the 6 drive plate and torque converter setting bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

First install the black colored bolt and then the remaining 5 silver colored bolts.



Hide 5.INSTALL STIFFENER PLATE

a.

Install the No. 2 end plate.


b.

Install the No. 4 cylinder block insulator.


c.

Install the stiffener plate LH to the engine and transmission with the 4 bolts.

Torque:
71 N*m (720 kgf*cm, 53 ft.*lbf)


d.

Install the stiffener plate RH (with clamp tube) to the engine and transmission with the 4 bolts.

Torque:
71 N*m (720 kgf*cm, 53 ft.*lbf)


Hide 6.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
13 N*m (128 kgf*cm, 9 ft.*lbf)


Hide 7.CONNECT ENGINE WIRE

a.

Connect the connectors.

i.

Connect the temperature sensor connector.


ii.

Connect the park/neutral position switch connector.


iii.

Connect the 3 speed sensor connectors.


iv.

Connect the transmission wire connector.



Hide 8.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the engine mounting insulator to the transmission with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 9.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the 4 set bolts of the engine mounting insulator.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


b.

Install the frame crossmember with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 11.CONNECT GROUND CABLE

a.

Connect the earth wire with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 12.CONNECT TRANSMISSION CONTROL SHIFT CABLE ASSEMBLY

a.

Connect the control cable with a new clip.


b.

Connect the control cable with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 13.INSTALL OIL COOLER TUBE

G034255
0.563,1.635 0.885,1.938 true 1.802,1.688 1.948,1.969 true 2.552,1.688 3.073,1.781 true 0.958,1.896 1.167,2.094 0.208,0.198 10 true C 1.99,1.969 2.177,2.167 0.188,0.198 10 true B 3.135,1.708 3.302,1.885 0.167,0.177 10 true A

a.

Loosely install the tip of the oil cooler tube inlet to the automatic transmission by hand.


b.

Loosely install the tip of the oil cooler tube outlet to the automatic transmission by hand.


c.

Install the 3 clamps with the 3 bolts.

Torque:
for Bolt A and B : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for Bolt C : 12 N*m (122 kgf*cm, 9 ft.*lbf)


d.

Using a union nut wrench, tighten the inlet and outlet tubes.

Torque:
34 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 14.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

a.

Coat a new O-ring with ATF, and install it to the oil filler tube.


b.

Install the oil filler tube with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Install the oil dipstick.


Hide 18.INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

a.
C213733C02
1.438,1.219 1.75,0.729 1.75,0.729 1.896,0.729 true 1.938,0.646 2.229,0.833 0.292,0.188 10 false *1
*1 Select Return Spring


While pushing the select return spring to the left with the end of the transfer high and low shift lever, insert the end of the shift lever into the shift fork.


b.
C213734C02
2.083,1.063 2.51,0.74 2.51,0.74 2.781,0.74 true 2.813,0.646 3.031,0.833 0.219,0.188 10 false *1
*1 Shift Lever Cap


While holding down the shift lever cap, install the snap ring to install the transfer high and low shift lever.


c.

Return the transfer front drive shift boot to its original position.


Hide 19.INSTALL SHIFT LEVER BOOT ASSEMBLY

a.

Install the shift lever boot with the 4 screws.


Hide 21.ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:

Toyota Genuine ATF TYPE T-IV


Hide 22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 24.CHECK FOR EXHAUST GAS LEAKS