Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turn the magnet clutch on based on the signal.

WIRING DIAGRAM

E253380
2.66,1.345 3.113,1.495 0.453,0.150 10 G154 2.66,0.621 3.074,0.771 0.413,0.150 10 G154 2.728,1.574 2.908,1.725 0.180,0.150 10 *5 2.728,0.851 2.908,1.001 0.180,0.150 10 *5 2.744,0.422 2.939,0.572 0.195,0.150 10 24 2.744,1.14 2.948,1.290 0.203,0.150 10 25 2.226,1.345 2.679,1.495 0.453,0.150 10 G146 2.226,0.621 2.639,0.771 0.413,0.150 10 G146 2.294,1.574 2.474,1.725 0.180,0.150 10 *4 2.294,0.851 2.474,1.001 0.180,0.150 10 *4 2.31,0.422 2.505,0.572 0.195,0.150 10 19 2.31,1.14 2.514,1.290 0.203,0.150 10 21 1.792,1.345 2.245,1.495 0.453,0.150 10 G156 1.792,0.621 2.205,0.771 0.413,0.150 10 G156 1.86,1.574 2.040,1.725 0.180,0.150 10 *3 1.86,0.851 2.040,1.001 0.180,0.150 10 *3 1.876,0.422 2.070,0.572 0.195,0.150 10 10 1.876,1.14 2.079,1.290 0.203,0.150 10 13 1.357,1.345 1.811,1.495 0.453,0.150 10 G148 1.357,0.621 1.771,0.771 0.413,0.150 10 G148 1.425,1.574 1.605,1.725 0.180,0.150 10 *2 1.425,0.851 1.605,1.001 0.180,0.150 10 *2 1.441,0.422 1.636,0.572 0.195,0.150 10 10 1.441,1.14 1.645,1.290 0.203,0.150 10 13 0.22,5.335 1.275,5.491 1.055,0.157 10 *5: for 1GR-FE 0.22,5.057 1.275,5.213 1.055,0.157 10 *4: for 2TR-FBE 0.22,4.502 1.824,4.658 1.604,0.157 10 *2: for 1KD-FTV for DPF 0.22,4.779 1.868,4.936 1.648,0.157 10 *3: for 1KD-FTV for i-ART 0.22,4.224 3.169,4.380 2.949,0.157 10 *1: for 1KD-FTV except DPF and i-ART 6.04,0.627 6.333,0.878 0.292,0.251 10 AC1 6.031,1.328 6.383,1.521 0.353,0.193 10 ACT 6.049,2.493 6.427,2.729 0.378,0.236 10 MGC 2.044,3.6 3.415,3.850 1.370,0.250 10 Magnet Clutch Relay 0.123,3.694 1.427,3.920 1.304,0.226 10 from Ignition Switch 5.002,4.553 6.923,4.752 1.921,0.199 10 - Magnet Clutch Assembly 5.002,4.293 6.923,4.492 1.921,0.199 10 Cooler Compressor Assembly 0.455,1.883 0.865,2.062 0.409,0.180 10 ECM 0.538,0.623 0.903,0.806 0.364,0.184 10 AC1 0.533,1.372 0.892,1.556 0.360,0.184 10 ACT 5.407,2.963 5.782,3.114 0.375,0.150 10 G94 5.727,2.392 5.906,2.543 0.179,0.150 10 13 5.008,4.149 5.369,4.299 0.362,0.150 10 C33 2.044,3.461 2.361,3.612 0.316,0.150 10 G71 5.791,1.241 5.907,1.391 0.116,0.150 10 7 2.97,2.399 3.085,2.549 0.116,0.150 10 1 4.773,3.931 4.888,4.081 0.116,0.150 10 1 2.18,2.399 2.295,2.549 0.116,0.150 10 2 2.992,3.042 3.107,3.193 0.116,0.150 10 3 2.187,3.042 2.303,3.193 0.116,0.150 10 5 5.739,0.51 5.918,0.660 0.179,0.150 10 21 1.051,0.422 1.251,0.572 0.199,0.150 10 18 1.062,1.574 1.242,1.725 0.180,0.150 10 *1 1,1.346 1.289,1.496 0.289,0.150 10 G38 1.062,0.851 1.242,1.001 0.180,0.150 10 *1 1,0.622 1.289,0.773 0.289,0.150 10 G38 1.051,1.14 1.279,1.290 0.228,0.150 10 19 5.407,3.103 7.032,3.706 1.625,0.603 10 Air Conditioning Amplifier Assembly 0.483,2.668 1.631,2.842 1.147,0.174 10 ECU-IG&GAUGE

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (A/C SIGNAL)
a.

Use the Data List to check if the magnet clutch on request signal is functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST

ECM
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/C Signal Magnet clutch on request signal / ON or OFF ON: A/C switch on
OFF: A/C switch off
Check this item with the engine idling and the blower switch on (LO level).

OK:

Display is as specified in normal condition.



Result:
Proceed to
OK
NG



OK

2.INSPECT MAGNET CLUTCH RELAY

NG

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
2.INSPECT MAGNET CLUTCH RELAY
a.
E272300
2.667,0.729 3.052,0.563 true 2.01,0.698 1.625,0.51 true 2.333,1.5 1.958,1.865 true 2.448,1.146 3.021,1.667 true 1.51,0.438 1.667,0.635 0.156,0.198 10 false 1 0.385,1.229 0.542,1.427 0.156,0.198 10 false 1 1.417,1.229 1.573,1.427 0.156,0.198 10 false 2 1.427,0.771 1.583,0.969 0.156,0.198 10 false 5 0.385,0.771 0.542,0.969 0.156,0.198 10 false 3 1.875,1.844 2.031,2.042 0.156,0.198 10 false 3 3.094,0.469 3.25,0.667 0.156,0.198 10 false 2 3.094,1.677 3.25,1.875 0.156,0.198 10 false 5

Remove the magnet clutch relay.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY(for Magnet Clutch Control)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.
E272301
0.302,1.042 0.698,1.344 0.396,0.302 1.979,1.438 2.667,1.083 true 2.729,1.01 3.188,1.208 0.458,0.198 10 false MGC 0.146,0.104 0.604,0.302 0.458,0.198 10 false *a 0.375,1.115 0.833,1.313 0.458,0.198 10 false G94
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the G94 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G94-13 (MGC) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
0.698,0.052 1.167,0.302 0.469,0.25 0.76,0.99 1.292,1.729 true 0.802,0.104 1.135,0.281 0.333,0.177 10 false G94 1.313,1.729 1.677,1.917 0.365,0.188 10 false MGC 0.073,0 0.292,0.198 0.219,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-13 (MGC) - Body ground
·

Engine idling

·

A/C switch on (magnet clutch on permitted)


Below 1 V
·

Engine idling

·

A/C switch off or on (magnet clutch not on permitted)


11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT MAGNET CLUTCH ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
5.INSPECT MAGNET CLUTCH ASSEMBLY

b.

Apply battery voltage to the magnet clutch and check operation of the magnet clutch.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Ground wire
Magnet clutch engages


Result:
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2TR-FBE) C
NG (for 1GR-FE) D




A

6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - MAGNET CLUTCH RELAY)

B

C

D

6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - MAGNET CLUTCH RELAY)
a.

Disconnect the C33 cooler compressor assembly connector.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G71-5 - Body ground Ignition switch ON 11 to 14 V
Ignition switch ON Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G71-3 - C33-1 Always Below 1 Ω
G71-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.

Disconnect the G38*1, G148*2, G156*3, G146*4, or G154*5 ECM connectors.

*1: for 1KD-FTV except DPF and i-ART

*2: for 1KD-FTV for DPF

*3: for 1KD-FTV for i-ART

*4: for 2TR-FBE

*5: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV except DPF and i-ART
Tester Connection Condition Specified Condition
G94-21 (AC1) - G38-18 (AC1) Always Below 1 Ω
G94-21 (AC1) - Body ground Always 10 kΩ or higher

for 1KD-FTV for DPF
Tester Connection Condition Specified Condition
G94-21 (AC1) - G148-10 (AC1) Always Below 1 Ω
G94-21 (AC1) - Body ground Always 10 kΩ or higher

for 1KD-FTV for i-ART
Tester Connection Condition Specified Condition
G94-21 (AC1) - G156-10 (AC1) Always Below 1 Ω
G94-21 (AC1) - Body ground Always 10 kΩ or higher

for 2TR-FBE
Tester Connection Condition Specified Condition
G94-21 (AC1) - G146-19 (AC1) Always Below 1 Ω
G94-21 (AC1) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G94-21 (AC1) - G154-24 (AC1) Always Below 1 Ω
G94-21 (AC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
0.698,0.052 1.167,0.302 0.469,0.25 0.875,1.198 1.406,1.74 true 0.802,0.104 1.146,0.281 0.344,0.177 10 false G94 1.313,1.76 1.677,1.948 0.365,0.188 10 false AC1 0.073,0.063 0.292,0.26 0.219,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-21 (AC1) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V


Result:
Result Proceed to
OK (for 1KD-FTV) A
OK (for 2TR-FBE) B
OK (for 1GR-FE) C
NG D




A

B

C

D

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.

Disconnect the G38*1, G148*2, G156*3, G146*4, or G154*5 ECM connectors.

*1: for 1KD-FTV except DPF and i-ART

*2: for 1KD-FTV for DPF

*3: for 1KD-FTV for i-ART

*4: for 2TR-FBE

*5: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV except DPF and i-ART
Tester Connection Condition Specified Condition
G94-7 (ACT) - G38-19 (ACT) Always Below 1 Ω
G94-7 (ACT) - Body ground Always 10 kΩ or higher

for 1KD-FTV for DPF
Tester Connection Condition Specified Condition
G94-7 (ACT) - G148-13 (ACT) Always Below 1 Ω
G94-7 (ACT) - Body ground Always 10 kΩ or higher

for 1KD-FTV for i-ART
Tester Connection Condition Specified Condition
G94-7 (ACT) - G156-13 (ACT) Always Below 1 Ω
G94-7 (ACT) - Body ground Always 10 kΩ or higher

for 2TR-FBE
Tester Connection Condition Specified Condition
G94-7 (ACT) - G146-21 (ACT) Always Below 1 Ω
G94-7 (ACT) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G94-7 (ACT) - G154-25 (ACT) Always Below 1 Ω
G94-7 (ACT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
0.698,0.052 1.167,0.302 0.469,0.25 1.51,0.979 1.406,1.74 true 0.792,0.115 1.135,0.292 0.344,0.177 10 G94 1.229,1.729 1.594,1.917 0.365,0.188 10 ACT 0.073,0 0.292,0.198 0.219,0.198 10 *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-7 (ACT) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


Below 1 V



Result:
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2TR-FBE) C
NG (for 1GR-FE) D



A

B

C

D