ECD SYSTEM (for i-ART) > Black Smoke Emitted |
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
| Symptom and Corresponding Main Fault |
| |
| Data List | MAP | |
| Main fault | Glow system malfunction | |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) | |
| Data List | Check the glow plug indicator light | |
| Diagnostic Point | Measure the resistance of the glow plug | |
| Main fault | Loss of compression | |
| Symptoms | Rough idle (lack of power always) | |
| Data List | Engine Speed of Cyl
| |
Diesel Injection
| Main fault | - | |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
| |
| Diagnostic Trouble Code | Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored. | |
| Main fault | Blockage, increase in fuel injection volume | |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Injection Feedback Val
| |
| Main fault | Circuit fault: The injector assembly does not open. | |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Same as injector assembly | |
| Diagnostic Trouble Code | When the injector driver has a fault, some DTCs may be stored. | |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) | |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure
| |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. | |
| Main fault | - | |
| Symptoms | Difficult to start, rough idle (especially when cold) | |
Diesel EGR
| Main fault |
| |
| Symptoms |
| |
| Data List | Actual EGR Valve Pos., Target EGR Position
| |
Diesel Throttle
| Main fault | Stuck, does not move smoothly | |
| Symptoms |
| |
| Data List |
| |
| Data List Related to Black Smoke |
| Explanation of Symptom |
| Black Smoke | The fuel used in diesel engines has a higher boiling point and evaporates much slower than that used in gasoline engines. Additionally, the fuel is injected directly, so the air fuel mixture in diesel engines is formed in a very short period of time and is less homogenous. This is why diesel engines must operate with a larger air fuel ratio across the entire operating range. An insufficient quantity of air results in imperfect combustion and increased particulate (soot) emissions. When the accelerator pedal is depressed, a large amount of fuel is injected. As a result, the air fuel ratio becomes rich. In this relatively rich environment, fuel droplets lacking in oxygen burn imperfectly producing soot, which is emitted as black smoke. In order to prevent black smoke production, the maximum injection quantity for a given intake air mass is limited (final injection quantity is limited by MAF). Black smoke is emitted when either 1) a lack of oxygen is present during combustion, or 2) too much fuel is injected for a given intake air mass and the air fuel ratio becomes temporarily rich. |
| 1.READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
| No DTCs are output | A |
| Engine related DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK FOR BLACK SMOKE |
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it.*1
Repeat the above procedure *1 10 times or more.*2
Check for black smoke emission during procedures *1 and *2.
|
| ||||
| NG | |
| 3.CHECK AIR INTAKE SYSTEM |
Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT |
Check the wire harness and connector connections of common rail system components.
|
| ||||
| OK | |
| 5.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data.
Take a snapshot of the following Data List items.
| NEXT | |
| 6.READ VALUE USING GTS (MAF AND MAP) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine / Data List / MAP and MAF.
Take a snapshot when the engine speed is maintained at 4000 rpm with no load.
Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.
| Result | Proceed to |
| MAF 84 gm/s or more and MAP 105 kPa or higher | A |
| Except above | B |
|
| ||||
| B | |
| 7.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE) |
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
| Active Test | Result | Proceed to |
| Activate the EGR Valve Close: Off (Open) to On (Closed) | MAF value does not change | A |
| MAF value changes | B |
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
| Open (55%) |
| 3 to 10 gm/s |
| Closed (0%) | 12 to 21 gm/s |
|
| ||||
| A | |
| 8.READ VALUE USING GTS (MAF) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / MAF.
With the ignition switch ON and engine stopped, read the value when 30 seconds has elapsed.
| Tester Display | Switch Condition | Standard |
| MAF | Ignition switch ON (do not start engine) | Less than 0.35 gm/s |
|
| ||||
| OK | |
| 9.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS) |
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position.
Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
| Tester Display | Result | Proceed to |
| Activate the VSV for EGR Cooler Bypass: Cooler to Bypass | MAF value does not change | A |
| MAF value changes | B |
|
| ||||
| A | |
| 10.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY) |
Remove the electric EGR control valve assembly (Click here).
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
Reinstall the electric EGR control valve assembly (Click here).
| NEXT | |
| 11.REPLACE EGR COOLER |
Replace the EGR cooler (Click here).
|
| ||||
| 12.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
|
| ||||
| 13.CHECK SNAPSHOT (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #4) |
Check Injection Feedback Val # and Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute.
| Result | Proceed to |
| Injection Volume is less than 10 mm3/st at 4000 rpm | A |
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st | B |
| Except above | C |
|
| ||||
|
| ||||
| A | |
| 14.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS |
Replace the injector assemblies (Click here).
|
| ||||
| 15.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Check the engine speed during the Active Test.
| Result | Proceed to |
| Except below | A |
| The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other | B |
|
| ||||
| A | |
| 16.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER |
Check the cylinder compression pressure .
|
| ||||
| OK | |
| 17.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4) |
Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 5 when the engine was idling and at 4000 rpm.
Record the value displayed for Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.
| NEXT | |
| 18.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly of the malfunctioning cylinder (Click here).
| NEXT | |
| 19.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 20.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 21.CHECK FOR BLACK SMOKE |
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it.*1
Repeat the above procedure *1 10 times.*2
Check for black smoke emission during procedures *1 and *2.
| NEXT | ||
| ||
| 22.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4) |
Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 5 when the engine was idling and at 4000 rpm.
| Result | Proceed to |
| The value for Injector Leaking Count #1 to #4 does not change from 0 The value for i-ART Learning Status History #1 to #4 does not change from 0 Trip | A |
| The value for Injector Leaking Count #1 to #4 displays 1 or more The value for i-ART Learning Status History #1 to #4 displays 1 Trip or more | B |
|
| ||||
| B | |
| 23.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly (Click here).
|
| ||||
| 24.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / MAP and Atmosphere Pressure.
Compare MAP to Atmosphere Pressure when the ignition switch is turned to ON (engine stopped).
| Result | Proceed to |
| MAP and Atmosphere Pressure have same value | A |
| Atmosphere Pressure is different from actual atmospheric pressure | B |
| MAP is different from actual atmospheric pressure | C |
|
| ||||
|
| ||||
| A | |
| 25.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

|
| ||||
| OK | |
| 26.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE) |
Connect the GTS to the DLC3.
Soak the engine for a long time.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
|
| ||||
| OK | |
| 27.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP (TURBO)) |
Connect the GTS to the DLC3.
Soak the engine for a long time.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air, Intake Air Temp (Turbo).
|
| ||||
|
| ||||
| 28.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S8-1 - E27-23 (PCV+) | Always | Below 1 Ω |
| S8-2 - E27-12 (PCV-) | Always | Below 1 Ω |
| S8-1 or E27-23 (PCV+) - Body ground | Always | 10 kΩ or higher |
| S8-2 or E27-12 (PCV-) - Body ground | Always | 10 kΩ or higher |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 29.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP |
Disconnect the inlet hose from the Fuel Supply Pump.
Operate the priming pump and check that fuel is being supplied to the Fuel Supply Pump.
Reconnect the inlet hose.
|
| ||||
| OK | |
| 30.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE) |
Replace the fuel supply pump assembly (Click here).
| NEXT | |
| 31.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 32.PERFORM SUPPLY PUMP INITIALIZATION |
Perform supply pump initialization (Click here).
|
| ||||
| 33.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 34.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
|
| ||||
| 35.CHECK AND REPLACE ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
Replace the engine coolant temperature sensor (Click here).
|
| ||||
| 36.CHECK AND REPLACE MALFUNCTIONING PARTS |
Inspect the mass air flow meter (Click here).
Inspect the intake air temperature sensor (turbo) (Click here).
Replace the mass air flow meter (Click here).
Replace the intake air temperature sensor (turbo) (Click here).
|
| ||||
| 37.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 38.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP) |
Check and replace the clogged fuel pipe.
| NEXT | |
| 39.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 40.CHECK FOR BLACK SMOKE |
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it.*1
Repeat the above procedure *1 10 times.*2
Check for black smoke emission during procedures *1 and *2.
| NEXT | ||
| ||
| 41.RECOVERY TO NORMAL |
| NEXT | ||
| ||