DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT |
| 1. DRAIN DIFFERENTIAL OIL |
for front differential:
Stop the vehicle on a level surface.
![]() |
Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.
| *1 | 10 mm Straight Hexagon Wrench |
| *2 | 10 mm Union Nut Wrench |
| *3 | Socket Adaptor |
Remove the drain plug and gasket, and drain the oil.
Install a new gasket and the drain plug.
for rear differential:
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Remove the drain plug and gasket, and drain the oil.
Install a new gasket and the drain plug.
| 2. REMOVE REAR PROPELLER SHAFT ASSEMBLY |
for DANA Made:
(Click here)
except DANA Made:
(Click here)
| 3. REMOVE REAR DRIVE PINION NUT |
![]() |
Using SST and a hammer, loosen the staked part of the nut.
![]() |
Using SST to hold the companion flange in place, remove the nut.
| *a | Turn |
| *b | Hold |
| 4. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR |
![]() |
Using SST, remove the companion flange with dust deflector.
| 5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST, remove the oil seal.
| *1 | Oil Seal |
| *2 | Oil Slinger |
| 6. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
![]() |
Remove the oil slinger from the drive pinion.
| 7. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the roller bearing (inner).
![]() |
Using SST, tap out the roller bearing (outer).
| 8. REMOVE DIFFERENTIAL OIL STORAGE RING |
Using a screwdriver and hammer, tap out the oil storage ring.
| 9. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
Remove the bearing spacer from the drive pinion.
| 10. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
![]() |
Install a new bearing spacer.
| 11. INSTALL DIFFERENTIAL OIL STORAGE RING |
Using a brass bar and hammer, tap in a new oil storage ring.
| 12. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a hammer, tap in the roller bearing (outer).
Install the roller bearing (inner).
| 13. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
![]() |
Install the oil slinger to the drive pinion.
| 14. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL |
Apply MP grease to the lip of the oil seal.
![]() |
Using SST and a hammer, tap in a new seal.
| *a | Oil Seal Depth |
| 15. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR |
![]() |
Using SST, install the companion flange with dust deflector.
Apply hypoid gear oil LSD to drive pinion thread and nut seat face.
![]() |
Using SST to hold the companion flange in place, install a new nut.
| *1 | Turn |
| *1 | Hold |
| 16. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload.
| Bearing | Specified Condition |
| New | 1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf) |
| Reused | 0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf) |
| 17. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| Bearing | Specified Condition |
| New | 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload |
| Reused | 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload |
| 18. STAKE REAR DRIVE PINION NUT |
![]() |
Using a chisel and hammer, stake the nut.
| 19. INSTALL REAR PROPELLER SHAFT ASSEMBLY |
for DANA Made:
(Click here)
except DANA Made:
(Click here)
| 20. ADD DIFFERENTIAL OIL |
![]() |
Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.
| *a | 0 to 5 mm (0 to 0.196 in.) |
| Temperature | Viscosity |
| Above -18°C (0°F) | SAE 90 |
| Below -18°C (0°F) | SAE 80W-90 or SAE 80W |
| Item | Oil type |
| Front Differential Rear differential | Hypoid gear oil API GL-5 or equivalent |
| Rear differential (for LSD) | Hypoid gear oil LSD API GL-5 or equivalent |
| Item | Specified Condition |
| Front Differential | 1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.) |
| Rear differential | 3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.) |
| Rear differential (w/ Differential Lock) | 2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.59 Imp. qts.) |
| 4WD, Pre-runner and made for DANA | 2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.) |
Check for oil leakage when the oil level is low.
for front differential:
![]() |
Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.
| *1 | 10 mm Straight Hexagon Wrench |
| *2 | 10 mm Union Nut Wrench |
| *3 | Socket Adaptor |
for rear differential:
Install a new gasket and the differential filler plug.