DTC P0400 Exhaust Gas Recirculation Flow |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0400 | When either condition below is met:
|
|


| 1.CHECK OTHER DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC output) | Proceed to |
| P0400 | A |
| P0400 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up (engine coolant temperature is 70°C (158°F) or higher) with the A/C switch and all accessory switches off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the tester on.
Select the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the tester while the engine is idling.
Select the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
| Active Test | Result | Proceed to |
| Activate the EGR Valve Close: Off (Open) to on (Closed) | MAF value does not change | A |
| MAF value changes | B |
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
| Open (55%) |
| 3.0 to 9.0 gm/s |
| Closed (0%) | 15 to 22 gm/s |
|
| ||||
| A | |
| 3.INSPECT VACUUM PUMP ASSEMBLY |
Check the negative pressure of the vacuum pump.
|
| ||||
| OK | |
| 4.CHECK VACUUM HOSE |
Check the vacuum hoses.
|
| ||||
| OK | |
| 5.INSPECT E-VRV FOR EGR |
Inspect the E-VRV (Click here).
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (E-VRV FOR EGR - ECM) |
![]() |
Disconnect the V1 E-VRV connector.
Disconnect the E6 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E6-9 (EGR) - V1-2 | Below 1 Ω |
| E6-9 (EGR) or V1-2 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK WIRE HARNESS (E-VRV FOR EGR - INTEGRATION RELAY (MAIN RELAY)) |
![]() |
Remove the integration relay from the engine room junction block.
Disconnect the 1J integration relay connector.
Disconnect the V1 E-VRV connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| 1J-5 - V1-1 | Below 1 Ω |
| 1J-5 or V1-1 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT VSV FOR EGR CUT |
Inspect the VSV for EGR cut (Click here).
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (VSV FOR EGR CUT - ECM) |
![]() |
Disconnect the V2 VSV for EGR Cut connector.
Disconnect the E6 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E6-18 (EGRC) - V2-2 | Below 1 Ω |
| E6-18 (EGRC) or V2-2 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (VSV FOR EGR CUT - INTEGRATION RELAY (MAIN RELAY)) |
![]() |
Remove the integration relay from the engine room junction block.
Disconnect the 1J integration relay connector.
Disconnect the V2 VSV for EGR Cut connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| 1J-5 - V2-1 | Below 1 Ω |
| 1J-5 or V2-1 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.INSPECT EGR VALVE ASSEMBLY |
Inspect the EGR valve assembly (Click here).
|
| ||||
|
| ||||
| 12.REPLACE EGR VALVE ASSEMBLY |
Replace the EGR valve assembly (Click here).
| NEXT | |
| 13.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR VALVE ASSEMBLY) |
Check for blockage in the EGR gas passage between the exhaust manifold and EGR valve assembly.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 14.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA |
Repair or replace the malfunctioning parts, component and area.
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F).
Move the shift lever to 2nd gear and decelerate from a speed of 50 km/h (31 mph) or more (fully closing the accelerator for approximately 5 seconds or more).
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTC.
| Display (DTC Output) | Proceed to |
| P0400 | A |
| No output | B |
|
| ||||
| A | |
| 16.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F).
Move the shift lever to 2nd gear and decelerate from a speed of 50 km/h (31 mph) or more (fully closing the accelerator for approximately 5 seconds or more).
Select the following menu items: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||