DTC P1251 Turbocharger / Supercharger Overboost Condition (Too High) |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Vehicle being driven | Boost pressure is higher than the threshold* for 5 seconds (1 trip detection logic). |
|
| DTC No. | Data List |
| P1251 |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P1251 is output | A |
| P1251 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK AIR INTAKE SYSTEM |
Check if the hoses between the air cleaner and turbocharger, and turbocharger and intake manifold are damaged or disconnected.
| Result | Proceed to |
| Hoses or pipes are damaged or disconnected | A |
| No hoses or pipes are damaged or disconnected | B |
|
| ||||
| A | |
| 3.REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
| NEXT | |
| 4.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION) |
Check the turbocharger sub-assembly .
|
| ||||
| OK | |
| 5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE) |
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
| Active Test | Result | Proceed to |
| Activate the EGR Valve Close: Off (Open) to On (Closed) | MAF value does not change | A |
| MAF value changes | B |
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
| Open (55%) |
| 3 to 10 gm/sec |
| Closed (0%) | 12 to 21 gm/sec |
|
| ||||
| A | |
| 6.READ VALUE USING GTS (TARGET EGR POSITION AND ACTUAL EGR VALVE POS.) |
Check the change in the values of "Target EGR Position" and "Actual EGR Valve Pos." in the Data List from the time when the "Control the EGR Step Position" or "Activate the EGR valve Close" Active Test was performed in the previous step.
| Result | Proceed to |
| Even though "Target EGR Position" indicated that the system was commanding the valve to open, "Actual EGR Valve Pos." remained near 0% and did not change | A |
| Other than above ("Actual EGR Valve Pos." changed according to the EGR valve open/close commands of the Active Test) | B |
|
| ||||
| A | |
| 7.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY) |
Remove the electric EGR control valve assembly (Click here).
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
Reinstall the electric EGR control valve assembly (Click here).
|
| ||||
| 8.REPLACE EGR COOLER |
Replace the EGR cooler (Click here).
|
| ||||
| 9.READ VALUE USING GTS (INJECTION VOLUME) |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher.
Allow the engine to idle for 1 minute or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Injection Volume.
Read the values during engine idling.
| Result | Proceed to |
| Injection Volume is less than 5 mm3/st | A |
| Except above | B |
|
| ||||
| A | |
| 10.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS |
Replace the injector assemblies (Click here).
| NEXT | |
| 11.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine and warm it up.
Confirm the value of Engine Speed from the Freeze Frame Data recorded previously, and then drive the vehicle according to the Engine Speed value.
Read the DTCs.
| Result | Proceed to |
| P1251 is not output and the amount by which MAP exceeds Target Boost Pressure is 20 kPa or less | A |
| Except above | B* |
|
| ||||
| A | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (ECM - TURBOCHARGER SUB-ASSEMBLY) |
Disconnect the DC motor connector.
Disconnect the nozzle vane position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T10-1 (M-) - E28-14 (M-) | Always | Below 1 Ω |
| T10-2 (M+) - E28-15 (M+) | Always | Below 1 Ω |
| T11-1 (VTA1) - E30-11 (VNA) | Always | Below 1 Ω |
| T11-2 (VNE2) - E30-5 (VNE2) | Always | Below 1 Ω |
| T11-3 (VNVC) - E30-17 (VNVC) | Always | Below 1 Ω |
| T10-1 (M-) or E28-14 (M-) - Body ground | Always | 10 kΩ or higher |
| T10-2 (M+) or E28-15 (M+) - Body ground | Always | 10 kΩ or higher |
| T11-1 (VTA1) or E30-11 (VNA) - Body ground | Always | 10 kΩ or higher |
| T11-3 (VNVC) or E30-17 (VNVC) - Body ground | Always | 10 kΩ or higher |
Reconnect the DC motor connector.
Reconnect the nozzle vane position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||