Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)
RM33K0E _58 Vehicle Interior _043547 DOOR LOCK _0222443 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and wireless door lock buzzer answer-back function does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the body ECU may be malfunctioning.

WIRING DIAGRAM

E322033E05
3.927,0.375 4.385,0.573 0.458,0.198 10 false HAZ 2.99,0.76 5.167,1 2.177,0.24 10 false Combination Meter Assembly 2.99,0.594 3.448,0.792 0.458,0.198 10 false G10 4.333,0.25 4.792,0.448 0.458,0.198 10 false 2 6.031,0.25 6.49,0.448 0.458,0.198 10 false HAZ 5.781,0.25 6.24,0.448 0.458,0.198 10 false 6 6.698,0.958 7.031,1.156 0.333,0.198 10 false +B 6.698,1.833 7.031,2.031 0.333,0.198 10 false +B 6.021,1.25 6.479,1.448 0.458,0.198 10 false LSWD 6.021,2.125 6.479,2.323 0.458,0.198 10 false LSWP 5.729,1.25 6.188,1.448 0.458,0.198 10 false 15 5.792,2.135 6.25,2.333 0.458,0.198 10 false 2 0.604,1.698 1.323,1.906 0.719,0.208 10 false K1*1, J1*2 0.594,1.865 2.271,2.229 1.677,0.365 10 false Front Door Lock Assembly LH*1, RH*2 1.552,1.271 2.01,1.469 0.458,0.198 10 false LSSR 0.958,1.271 1.417,1.469 0.458,0.198 10 false E 2.042,1.26 2.75,1.49 0.708,0.229 10 false 8*1, 7*2 0.333,1.26 1.083,1.458 0.75,0.198 10 false 7*1, 8*2 3.958,2.146 4.417,2.344 0.458,0.198 10 false LSSR 1.563,3 2.021,3.198 0.458,0.198 10 false LSSR 3.969,3.427 4.427,3.625 0.458,0.198 10 false LSSR 0.958,3 1.417,3.198 0.458,0.198 10 false E 3.333,3.427 3.792,3.625 0.458,0.198 10 false E 3.344,2.156 3.802,2.354 0.458,0.198 10 false E 2.031,2.99 2.49,3.188 0.458,0.198 10 false 6 3.156,3.427 3.615,3.625 0.458,0.198 10 false 9 0.76,2.99 1.219,3.188 0.458,0.198 10 false 9 4.427,3.427 4.885,3.625 0.458,0.198 10 false 6 2.813,2.563 3.469,2.781 0.656,0.219 10 false J*1, K1*2 2.823,2.719 5.219,2.927 2.396,0.208 10 false Front Door Lock Assembly RH*1, LH*2 0.594,3.458 2.792,3.677 2.198,0.219 10 false Rear Door Lock Assembly RH 0.594,3.302 1.052,3.5 0.458,0.198 10 false L1 2.99,3.885 5.188,4.104 2.198,0.219 10 false Rear Door Lock Assembly LH 2.99,3.74 3.448,3.938 0.458,0.198 10 false M1 3.073,6.01 4.615,6.396 1.542,0.385 10 false Certification ECU (Smart Key ECU Assembly) 6.115,6 6.573,6.198 0.458,0.198 10 false G33 6.125,6.156 7.042,6.354 0.917,0.198 10 false Body ECU 6.031,5.167 6.49,5.365 0.458,0.198 10 false RDA 6.031,5.604 6.49,5.802 0.458,0.198 10 false PRG 5.719,5.052 6.177,5.25 0.458,0.198 10 false 16 5.792,5.49 6.25,5.688 0.458,0.198 10 false 9 0.698,5.76 3.073,5.979 2.375,0.219 10 false Wireless Door Lock Buzzer 0.708,5.594 1.167,5.792 0.458,0.198 10 false A41 0.844,5.052 1.302,5.25 0.458,0.198 10 false 2 2.198,5.052 2.656,5.25 0.458,0.198 10 false 1 2.698,5.167 3.156,5.365 0.458,0.198 10 false G16 4.719,4.729 5.177,4.927 0.458,0.198 10 false G16 4.708,5.177 5.167,5.375 0.458,0.198 10 false G17 4.719,5.604 5.177,5.802 0.458,0.198 10 false G17 4.76,4.958 5.219,5.156 0.458,0.198 10 false 13 4.771,5.406 5.229,5.604 0.458,0.198 10 false 36 3.094,5.052 3.552,5.25 0.458,0.198 10 false BZR 2.792,4.927 3.25,5.125 0.458,0.198 10 false 2 4.219,5.167 4.708,5.354 0.49,0.188 10 false RDA3 4.208,5.604 4.698,5.792 0.49,0.188 10 false PRG3 4.177,4.708 4.635,4.906 0.458,0.198 10 false LSWP 4.813,4.5 5.271,4.698 0.458,0.198 10 false 9 2.74,2.135 3.448,2.365 0.708,0.229 10 false 8*1, 7*2 4.417,2.104 5.167,2.302 0.75,0.198 10 false 7*1, 8*2 0.583,6.125 2.958,6.344 2.375,0.219 10 false *1: for LHD 0.594,6.417 2.969,6.635 2.375,0.219 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

The wireless door lock buzzer answer-back function can be customized. Make sure that this function is ON before performing this.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>CUSTOMIZE PARAMETERS

·

Before performing the inspection, check that DTC B27B0 (Smart Entry and Start System) is not output.

·

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION



PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the electrical key transmitter sub-assembly.


Result:
Result Proceed to
Wireless door lock/unlock operates properly A
Wireless door lock/unlock does not operate properly B



A

2.INSPECT DOOR LOCK ASSEMBLY (DETECTION UNLOCK SWITCH)

B

2.INSPECT DOOR LOCK ASSEMBLY (DETECTION UNLOCK SWITCH)
a.

for Front Side:

i.

Remove the front door lock assembly.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


ii.

Inspect the front door lock assembly.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION



b.

for Rear Side:

i.

Remove the rear door lock assembly.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>REMOVAL


ii.

Inspect the rear door lock assembly.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION



Result:
Result Proceed to
OK A
NG (for Front Side) B
NG (for Rear Side) C



A

3.CHECK HARNESS AND CONNECTOR (DOOR LOCK ASSEMBLY - BODY ECU, CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

B

REPLACE FRONT DOOR LOCK ASSEMBLY

C

REPLACE REAR DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DOOR LOCK ASSEMBLY - BODY ECU, CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

*1: for LHD

*2: for RHD


a.

for Driver Side:

i.

Disconnect the K1*1 or J1*2 front door lock assembly LH*1 or RH*2 connector.


ii.

Disconnect the G33 body ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
K1-8 (LSSR) - G33-15 (LSWD) Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
K1-8 (LSSR) or G33-15 (LSWD) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
J1-7 (LSSR) - G33-15 (LSWD) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
J1-7 (LSSR) or G33-15 (LSWD) - Body ground Always 10 kΩ or higher




b.

except Driver Side:

i.

Disconnect the J1*1 or K1*2 front door lock assembly RH*1 or LH*2 connector.


ii.

Disconnect the L1 rear door lock assembly RH connector.


iii.

Disconnect the M1 rear door lock assembly LH connector.


iv.

Disconnect the G33 body ECU connector.


v.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
J1-7 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
J1-7 (LSSR) - G69-9 (LSWP) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
J1-7 (LSSR) or G33-2 (LSWP) - Body ground Always 10 kΩ or higher
J1-7 (LSSR) or G69-9 (LSWP) - Body ground Always 10 kΩ or higher
L1-6 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
L1-6 (LSSR) - G69-9 (LSWP) Always Below 1 Ω
L1-9 (E) - Body ground Always Below 1 Ω
L1-6 (LSSR) - G33-2 (LSWP) - Body ground Always 10 kΩ or higher
L1-6 (LSSR) - G69-9 (LSWP) - Body ground Always 10 kΩ or higher
M1-6 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
M1-6 (LSSR) - G69-9 (LSWP) Always Below 1 Ω
M1-9 (E) - Body ground Always Below 1 Ω
M1-6 (LSSR) - G33-2 (LSWP) - Body ground Always 10 kΩ or higher
M1-6 (LSSR) - G69-9 (LSWP) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
K1-8 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
K1-8 (LSSR) - G69-9 (LSWP) Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
K1-8 (LSSR) or G33-2 (LSWP) - Body ground Always 10 kΩ or higher
K1-8 (LSSR) or G69-9 (LSWP) - Body ground Always 10 kΩ or higher
L1-6 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
L1-6 (LSSR) - G69-9 (LSWP) Always Below 1 Ω
L1-9 (E) - Body ground Always Below 1 Ω
L1-6 (LSSR) - G33-2 (LSWP) - Body ground Always 10 kΩ or higher
L1-6 (LSSR) - G69-9 (LSWP) - Body ground Always 10 kΩ or higher
M1-6 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
M1-6 (LSSR) - G69-9 (LSWP) Always Below 1 Ω
M1-9 (E) - Body ground Always Below 1 Ω
M1-6 (LSSR) - G33-2 (LSWP) - Body ground Always 10 kΩ or higher
M1-6 (LSSR) - G69-9 (LSWP) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK WIRELESS ANSWER-BACK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the electrical key transmitter sub-assembly.


Result:
Result Proceed to
Only wireless door lock buzzer answer-back does not occur A
Only hazard warning light answer-back does not occur B



A

5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)

B

9.CHECK HAZARD WARNING LIGHTS OPERATION
5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Operation Wireless door lock buzzer OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Wireless Buzzer Operation
50004 125 31

Result:
Result Proceed to
Wireless door lock buzzer does not turn on/off A
Wireless door lock buzzer turns on/off B



A

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the A41 wireless door lock buzzer connector.


b.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-1 - G16-2 (BZR) Always Below 1 Ω
A41-2 - Body ground Always Below 1 Ω
A41-1 or G16-2 (BZR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE WIRELESS DOOR LOCK BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Replace the wireless door lock buzzer with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
8.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Operation Wireless door lock buzzer OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Wireless Buzzer Operation
50004 125 31

Result:
Result Proceed to
Wireless door lock buzzer does not turn on/off A
Wireless door lock buzzer turns on/off B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE)

9.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning lights blink when the hazard warning signal switch is pressed.

OK:

Hazard warning lights blink.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)

NG

GO TO LIGHTING SYSTEM (PROCEED TO HAZARD WARNING SWITCH CIRCUIT)

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)
a.

Disconnect the G10 combination meter assembly connector.


b.

Disconnect the G33 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-2 (HAZ) - G33-6 (HAZ) Always Below 1 Ω
G10-2 (HAZ) or G33-6 (HAZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR