Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)
RM33K0E _58 Vehicle Interior _043547 DOOR LOCK _0222444 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light answer-back function does not operate. In such cases, hazard warning light signal outputs from the body ECU may be malfunctioning.

WIRING DIAGRAM

E328442E05
3.125,0.76 3.583,0.958 0.458,0.198 10 false G10 3.135,0.927 5.135,1.125 2,0.198 10 false Combination Meter Assembly 3.917,0.385 4.375,0.583 0.458,0.198 10 false HAZ 4.323,0.281 4.781,0.479 0.458,0.198 10 false 2 6.031,0.26 6.49,0.458 0.458,0.198 10 false HAZ 5.802,0.271 6.26,0.469 0.458,0.198 10 false 6 5.74,1.292 6.198,1.49 0.458,0.198 10 false 15 6.021,1.292 6.615,1.458 0.594,0.167 10 false LSWD 1.583,1.292 2.167,1.469 0.583,0.177 10 false LSSR 2.073,1.281 2.531,1.479 0.458,0.198 10 false 8 0.792,1.281 1.25,1.479 0.458,0.198 10 false 7 0.948,1.302 1.531,1.479 0.583,0.177 10 false E 0.615,1.771 1.073,1.969 0.458,0.198 10 false K1 0.625,1.979 2.625,2.177 2,0.198 10 false Front Door Lock Assembly LH 3.365,2.156 3.948,2.333 0.583,0.177 10 false E 3.135,2.135 3.594,2.333 0.458,0.198 10 false 8 3.958,2.156 4.542,2.333 0.583,0.177 10 false LSSR 4.438,2.115 4.896,2.313 0.458,0.198 10 false 7 2.885,2.792 4.885,2.99 2,0.198 10 false Front Door Lock Assembly RH 2.885,2.594 3.344,2.792 0.458,0.198 10 false J1 5.823,2.146 6.281,2.344 0.458,0.198 10 false 2 6.021,2.135 6.615,2.302 0.594,0.167 10 false LSWP 0.781,3.25 1.24,3.448 0.458,0.198 10 false 9 0.948,3.26 1.531,3.438 0.583,0.177 10 false E 1.563,3.25 2.146,3.427 0.583,0.177 10 false LSSR 2.031,3.24 2.49,3.438 0.458,0.198 10 false 6 0.5,3.948 2.5,4.146 2,0.198 10 false Rear Door Lock Assembly RH 0.5,3.781 0.958,3.979 0.458,0.198 10 false L1 3.354,3.938 3.938,4.115 0.583,0.177 10 false E 3.188,3.927 3.646,4.125 0.458,0.198 10 false 9 3.958,3.938 4.542,4.115 0.583,0.177 10 false LSSR 4.448,3.917 4.906,4.115 0.458,0.198 10 false 6 2.927,4.438 3.385,4.635 0.458,0.198 10 false M1 2.927,4.635 4.927,4.833 2,0.198 10 false Rear Door Lock Assembly LH 6.073,5.021 6.531,5.219 0.458,0.198 10 false G33 6.073,5.208 6.854,5.406 0.781,0.198 10 false Body ECU

CAUTION / NOTICE / HINT

NOTICE:
·

If the body ECU has been replaced, it is necessary to initialize the body ECU.*1

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

*1: w/ Automatic Light Control System

*2: w/ Door Control Battery




PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the door control transmitter.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock operates properly A
Wireless door lock/unlock does not operate properly B



A

2.INSPECT DOOR LOCK ASSEMBLY (DETECTION UNLOCK SWITCH)

B

2.INSPECT DOOR LOCK ASSEMBLY (DETECTION UNLOCK SWITCH)
a.

for Front Side:

i.

Remove the front door lock assembly.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


ii.

Inspect the front door lock assembly.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION



b.

for Rear Side:

i.

Remove the rear door lock assembly.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>REMOVAL


ii.

Inspect the rear door lock assembly.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION



Result:
Result Proceed to
OK A
NG (for Front Side) B
NG (for Rear Side) C



A

3.CHECK HARNESS AND CONNECTOR (DOOR LOCK ASSEMBLY - BODY ECU AND BODY GROUND)

B

REPLACE FRONT DOOR LOCK ASSEMBLY

C

REPLACE REAR DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DOOR LOCK ASSEMBLY - BODY ECU AND BODY GROUND)
a.

for Driver Side:

i.

Disconnect the K1 front door lock assembly RH connector.


ii.

Disconnect the G33 body ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K1-8 (LSSR) - G33-15 (LSWD) Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
K1-8 (LSSR) or G33-15 (LSWD) - Body ground Always 10 kΩ or higher




b.

except Driver Side:

i.

Disconnect the J1 front door lock assembly LH connector.


ii.

Disconnect the L1 rear door lock assembly RH connector.


iii.

Disconnect the M1 rear door lock assembly LH connector.


iv.

Disconnect the G33 body ECU connector.


v.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-7 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
J1-7 (LSSR) or G33-2 (LSWP) - Body ground Always 10 kΩ or higher
L1-6 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
L1-9 (E) - Body ground Always Below 1 Ω
L1-6 (LSSR) - G33-2 (LSWP) - Body ground Always 10 kΩ or higher
M1-6 (LSSR) - G33-2 (LSWP) Always Below 1 Ω
M1-9 (E) - Body ground Always Below 1 Ω
M1-6 (LSSR) - G33-2 (LSWP) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK HAZARD WARNING LIGHTS OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning light blinks when the hazard warning signal switch is pressed.

OK:

Hazard warning light signal is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)

NG

GO TO LIGHTING SYSTEM (PROCEED TO HAZARD WARNING SWITCH CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)
a.

Disconnect the G10 combination meter assembly connector.


b.

Disconnect the G33 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-2 (HAZ) - G33-6 (HAZ) Always Below 1 Ω
G10-2 (HAZ) or G33-6 (HAZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR