The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
1.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 2 wire harness clamp brackets to the manual transmission unit sub-assembly with the 2 bolts.
33019C
2.INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY
Connect the 2 clamps and install the transmission breather sub-assembly.
33030
3.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
Make sure that the knock pins are not loose, bent, damaged or scratched.
Operate the transmission jack and install the manual transmission unit assembly to the vehicle.
Do not raise the manual transmission unit assembly more than necessary. If the manual transmission unit assembly is raised excessively, the vehicle may also be lifted up.
Make sure that the manual transmission unit assembly is clear of all wiring and hoses.
Align the input shaft with the clutch disc and install the manual transmission unit assembly to the engine.
| *1 | Transmission Breather Bracket |
Install the transmission breather bracket and 7 bolts.
17118
4.INSTALL MANIFOLD STAY
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>INSTALLATION
for 2TR-FBE:
Click hereEngine / Hybrid System>2TR-FBE INTAKE / EXHAUST>EXHAUST MANIFOLD>INSTALLATION
12371A
5.INSTALL REAR ENGINE MOUNTING INSULATOR
Install the rear engine mounting insulator with the 4 bolts.
51204
6.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.
Connect the No. 3 frame crossmember sub-assembly to the rear engine mounting insulator.
28100
7.INSTALL STARTER ASSEMBLY
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for DENSO Made)>INSTALLATION
for 2TR-FBE:
Click hereEngine / Hybrid System>2TR-FBE STARTING>STARTER>INSTALLATION
8.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY
Install the clutch release cylinder assembly with the 2 bolts.
9.CONNECT WIRE HARNESS
Connect the 2 clamps and connector.
Connect the ground cable with the bolt.
17410
10.INSTALL FRONT EXHAUST PIPE ASSEMBLY
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION
for 2TR-FBE:
Click hereEngine / Hybrid System>2TR-FBE INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION
37100
11.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
for TASA Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TASA Made)>INSTALLATION
51442
12.INSTALL NO. 2 ENGINE UNDER COVER
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
for 2TR-FBE:
Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
51410
13.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
for 2TR-FBE:
Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
14.ADD MANUAL TRANSMISSION OIL
33530F
15.INSTALL FLOOR SHIFT LEVER ASSEMBLY
|
MP grease |
Apply MP grease to the tip of the shift lever.
| *1 | Shift Lever Cap |
| *a | Press Down |
| *b | Clockwise |
| *c | Lock |
Cover the shift lever cap with a cloth.
While pressing down on the shift lever cap, turn it clockwise to install the shift lever assembly.
Attach the shift lever cap boot.
58280A
16.INSTALL SHIFT LEVER BOOT ASSEMBLY
Install the shift lever boot assembly with the 6 screws and 4 clips.
Install the shift lever cover.
58810J
17.INSTALL CONSOLE BOX ASSEMBLY
18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION