83530
1.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
89422
2.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
11415
3.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Remove the cylinder block water drain cock sub-assembly.
Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.
11301M
4.REMOVE VVT SENSOR (for Bank 1)
11301M
5.REMOVE VVT SENSOR (for Bank 2)
11401G
6.REMOVE CRANKSHAFT POSITION SENSOR
15330B
7.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)
15340
8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)
15678A
9.REMOVE OIL CONTROL VALVE FILTER
| *A | for Bank 1 |
| *B | for Bank 2 |
Remove the 2 unions, 2 oil control valve filters and 2 gaskets.
15601
10.REMOVE OIL FILTER SUB-ASSEMBLY
15710
11.REMOVE OIL COOLER ASSEMBLY
15609
12.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY
16323
13.REMOVE WATER INLET ASSEMBLY
16356
14.REMOVE REAR WATER BY-PASS JOINT
Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.
Remove the O-ring from the No. 1 water outlet pipe.
12108
15.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly.
Remove the gasket from the oil filler cap sub-assembly.
12185
16.REMOVE OIL FILLER CAP HOUSING
Remove the 2 nuts, oil filler cap housing and gasket.
19100P
17.REMOVE SPARK PLUG
11201
18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
12204
19.REMOVE PCV VALVE SUB-ASSEMBLY
11202
20.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
21.SET NO. 1 CYLINDER TO TDC/COMPRESSION
13471
22.REMOVE CRANKSHAFT PULLEY
12101A
23.REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug and gasket.
12102A
24.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
15104
25.REMOVE OIL STRAINER SUB-ASSEMBLY
12101
26.REMOVE OIL PAN SUB-ASSEMBLY
11381
27.REMOVE ENGINE REAR OIL SEAL RETAINER
| *a | Pry |
| *b | Protective Tape |
Remove the 5 bolts and 2 nuts.
Using a screwdriver, remove the engine rear oil seal retainer by prying between the engine rear oil seal retainer and crankshaft bearing cap.
Tape the screwdriver tip before use.
11381A
28.REMOVE REAR CRANKSHAFT OIL SEAL
Using a screwdriver and hammer, tap out the rear crankshaft oil seal.
Be careful not to damage the engine rear oil seal retainer.
11302
29.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
16100
30.REMOVE ENGINE WATER PUMP ASSEMBLY
Remove the 8 bolts, engine water pump assembly and gasket.
11324
31.REMOVE TIMING CHAIN COVER PLATE
11303A
32.REMOVE FRONT CRANKSHAFT OIL SEAL
13540
33.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Never rotate the crankshaft with the No. 1 chain tensioner assembly removed.
When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from TDC first.
| *a | Push |
| *b | Stopper Plate |
While turning the stopper plate of the No. 1 chain tensioner assembly clockwise, push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.
While turning the stopper plate of the No. 1 chain tensioner assembly counterclockwise, insert a bar with a diameter of 3.5 mm (0.138 in.) into the holes in the stopper plate and No. 1 chain tensioner assembly to fix the stopper plate in place.
Remove the 2 bolts and No. 1 chain tensioner assembly.
13559
34.REMOVE CHAIN TENSIONER SLIPPER
13530
35.REMOVE IDLE SPROCKET ASSEMBLY
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.
13562
36.REMOVE NO. 2 CHAIN VIBRATION DAMPER
Remove the 2 No. 2 chain vibration dampers.
13506
37.REMOVE CHAIN SUB-ASSEMBLY
13521
38.REMOVE CRANKSHAFT TIMING SPROCKET
Remove the crankshaft timing sprocket.
13561
39.REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper.
40.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)
| *a | Raise |
While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 2 chain tensioner assembly in place.
Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the 2 bolts, camshaft timing gear sub-assembly, camshaft timing sprocket and No. 2 chain sub-assembly.
Do not damage the surrounding parts.
Do not disassemble the camshaft timing gear sub-assembly.
13550
41.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 2 chain tensioner assembly.
42.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)
| *a | Push |
While raising the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 3 chain tensioner assembly in place.
Hold the hexagonal portion of the No. 4 camshaft sub-assembly with a wrench and remove the 2 bolts, camshaft timing gear sub-assembly, camshaft timing sprocket and No. 2 chain sub-assembly.
Do not damage the surrounding parts.
Do not disassemble the camshaft timing gear sub-assembly.
13560A
43.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 3 chain tensioner assembly.
44.REMOVE CAMSHAFT BEARING CAP (for Bank 1)
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, make sure the following steps are carried out.
Rotate the camshaft and No. 2 camshaft counterclockwise and set the camshaft and No. 2 camshaft as shown in the illustration.
Uniformly loosen the 16 bolts in the sequence shown in the illustration and remove the bolts and 8 camshaft bearing caps.
13511
45.REMOVE CAMSHAFT
13512
46.REMOVE NO. 2 CAMSHAFT
11811
47.REMOVE NO. 1 CAMSHAFT BEARING
11821
48.REMOVE NO. 2 CAMSHAFT BEARING
49.REMOVE CAMSHAFT BEARING CAP (for Bank 2)
Uniformly loosen the 16 bolts in the sequence shown in the illustration and remove the bolts and 8 camshaft bearing caps.
13053
50.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
13054
51.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
11101
52.REMOVE CYLINDER HEAD SUB-ASSEMBLY
11115
53.REMOVE CYLINDER HEAD GASKET
11102
54.REMOVE CYLINDER HEAD LH
11116
55.REMOVE NO. 2 CYLINDER HEAD GASKET
16332
56.REMOVE NO. 1 WATER OUTLET PIPE
Remove the knock sensor wire.
for Type A:
Remove the 3 bolts and No. 1 water outlet pipe.
for Type B:
Remove the bolt, 2 nuts and No. 1 water outlet pipe.
89615
57.REMOVE KNOCK SENSOR
13751
58.REMOVE VALVE LIFTER
Remove the 24 valve lifters.
Arrange the removed parts so that they can be reinstalled in their original locations.
59.REMOVE TAPER SCREW PLUG
It is not necessary to remove a taper screw plug unless it is being replaced.
60.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.