Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL › 2015.06–2016.01
RM3250E _54 Brake _038045 BRAKE SYSTEM (OTHER) _0189587 BRAKE PEDAL N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL  ADJUSTMENT  


PROCEDURE

Hide 55214C 1.REMOVE NO. 2 DASH PANEL INSULATOR PAD

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.




b.

Remove the cowl side trim board LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>REMOVAL


c.

Fold back the front floor carpet assembly.


d.

Remove the No. 2 dash panel insulator pad.


Hide 2.CHECK AND ADJUST BRAKE PEDAL HEIGHT

a.

Check the pedal height.

If the brake pedal height is not as specified, adjust the brake pedal height according to the procedure below.

i.

for LHD:

Standard pedal height from floor panel:

167.7 to 177.7 mm (6.603 to 6.996 in.)


C326963C01
2.438,1.156 2.75,1.156 true 2.563,2.104 2.563,1.865 2.563,1.865 2.896,1.865 true 5.135,2 4.99,2.333 4.99,2.333 4.771,2.333 false 5.969,1.021 6.115,0.698 6.115,0.698 6.354,0.698 false 2.802,1.083 3.021,1.26 0.219,0.177 10 true *1 1.531,1.625 1.75,1.813 0.219,0.188 10 true *a 2.938,1.781 3.135,1.969 0.198,0.188 10 true *b 6.417,0.625 6.604,0.802 0.188,0.177 10 true *1 6.281,1.99 6.5,2.177 0.219,0.188 10 true *a 4.573,2.26 4.74,2.469 0.167,0.208 10 true *b
*1 Brake Pedal Pad - -
*a Brake Pedal Height *b Measuring Plane of Floor Panel



ii.

for RHD:

Standard pedal height from floor panel:

167.7 to 177.7 mm (6.603 to 6.996 in.)


C323708C01
2.448,1.188 2.75,1.188 true 2.229,1.833 2.229,1.646 2.229,1.646 2.698,1.646 true 5.167,2.021 5.063,2.344 5.063,2.344 4.802,2.344 false 6.01,1.021 6.271,0.625 6.271,0.625 6.479,0.625 false 2.802,1.115 3.01,1.292 0.208,0.177 10 true *1 1.531,1.594 1.719,1.781 0.188,0.188 10 true *a 2.781,1.573 2.969,1.771 0.188,0.198 10 true *b 6.292,2.01 6.479,2.198 0.188,0.188 10 true *a 4.583,2.271 4.771,2.469 0.188,0.198 10 true *b 6.521,0.542 6.729,0.719 0.208,0.177 10 true *1
*1 Brake Pedal Pad - -
*a Brake Pedal Height *b Measuring Plane of Floor Panel




b.

Adjust the pedal height.

i.
C323709C01
1.667,1.729 1.667,2.406 1.667,2.406 1.479,2.406 false 2.281,1.083 2.615,1.5 2.615,1.5 2.813,1.5 false 1.125,3.479 0.99,4 0.99,4 0.823,4 false 2.865,1.427 3.052,1.604 0.188,0.177 10 false *1 1.292,2.344 1.479,2.51 0.188,0.167 10 false *2 2.604,3.938 2.792,4.135 0.188,0.198 10 false *a 0.615,3.938 0.823,4.146 0.208,0.208 10 false *b
*1 Stop Light Switch Assembly
*2 Lock Nut
*a Brake Pedal Height
*b Floor Panel


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the push rod clevis lock nut.


iii.

Adjust the pedal height by turning the push rod.

Standard pedal height from floor panel:

167.7 to 177.7 mm (6.603 to 6.996 in.)



iv.

Tighten the lock nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION



Hide 3.CHECK BRAKE PEDAL FREE PLAY

C111306C07
2.052,1.458 2.375,1.802 0.323,0.344 10 false *a
*a Pedal Free Play


a.

Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.


b.

Depress the pedal until resistance is felt.


c.

Check the pedal free play by measuring the distance between the position in the previous step and the released position of the pedal.

Pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the free play is not as specified, check the switch clearance in the next step.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the free play is as specified, proceed to the "Check Brake Pedal Reserve Distance" procedure.


Hide 4.CHECK BRAKE PEDAL RESERVE DISTANCE

C111339C06
0.885,1.281 0.885,1.677 false 1.458,1.417 1.771,1.74 0.313,0.323 10 false *a 0.802,1.708 1.042,2.01 0.24,0.302 10 false *1
*1 Floor Panel
*a Pedal Reserve Distance


a.

Release the parking brake lever. Start the engine.


b.

Depress the pedal and check the pedal reserve distance.

i.

Depress the pedal with a force of 490 N (50 kgf, 110 lbf).


ii.

Measure the distance between the pedal and floor panel shown in the illustration.

If the distance is not as specified, troubleshoot the brake system.

Pedal Reserve Distance:
Item Model Specified Condition
w/o ABS for 2WD 90.0 mm (3.54 in.)
w/ ABS for LHD (w/o VSC) for 2WD except TGN121L-DTTSKV and TGN121L-DTTMKV 87.0 mm (3.43 in.)
for TGN121L-DTTSKV and TGN121L-DTTMKV 88.0 mm (3.46 in.)
for 4WD and Pre-Runner w/o 205R16C tire 91.0 mm (3.58 in.)
w/ 205R16C tire 92.0 mm (3.62 in.)
for LHD (w/ VSC) for 2WD 85.0 mm (3.35 in.)
for 4WD and Pre-Runner 91.0 mm (3.58 in.)
for RHD (w/o VSC) for 2WD 86.0 mm (3.39 in.)
for 4WD and Pre-Runner w/o 205R16C tire 90.0 mm (3.54 in.)
w/ 205R16C tire 91.0 mm (3.58 in.)
for RHD (w/ VSC) for 2WD 87.0 mm (3.43 in.)
for 4WD and Pre-Runner 90.0 mm (3.54 in.)




Hide 55214C 5.INSTALL NO. 2 DASH PANEL INSULATOR PAD

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



a.

Install the No. 2 dash panel insulator pad.


b.

Install the front floor carpet assembly to its original position.


c.