When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
No. 3 injection pipe sub-assembly ·
No. 4 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing Gear Case Assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
12315
1.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Install the front No. 1 engine mounting bracket LH to the cylinder block sub-assembly with the 4 bolts.
12311
2.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH
Install the front No. 1 engine mounting bracket RH to the cylinder block sub-assembly with the 4 bolts.
3.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
4.INSTALL CAMSHAFT POSITION SENSOR
5.INSTALL CRANKSHAFT POSITION SENSOR
44320
6.INSTALL VANE PUMP ASSEMBLY
Install a new O-ring to the vane pump assembly.
Install the vane pump assembly to the timing gear case assembly with the 2 nuts.
29300
7.INSTALL VACUUM PUMP ASSEMBLY
Install 2 new O-rings to the vacuum pump assembly.
Install the vacuum pump assembly to the timing gear cover with the 2 nuts.
15701C
8.INSTALL OIL COOLER COVER SUB-ASSEMBLY
22100
9.INSTALL FUEL SUPPLY PUMP ASSEMBLY
23810A
10.INSTALL COMMON RAIL ASSEMBLY
15601
11.INSTALL OIL FILTER SUB-ASSEMBLY
23804C
12.INSTALL FUEL INLET PIPE SUB-ASSEMBLY
19850
13.INSTALL GLOW PLUG ASSEMBLY
25617A
14.INSTALL NO. 2 EGR HOLE COVER PLATE
Install a new gasket and the No. 2 EGR hole cover plate.
17111
15.INSTALL INTAKE MANIFOLD
26100G
16.INSTALL DIESEL THROTTLE BODY ASSEMBLY
16331
17.INSTALL WATER OUTLET
| *a | Claw |
Install a new gasket and the water outlet to the cylinder head sub-assembly with the 2 bolts.
Make sure the claws of the gasket face the water outlet.
16331A
18.INSTALL THERMOSTAT
16321
19.INSTALL WATER INLET
88431
20.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET
Install the No. 1 compressor mounting bracket to the cylinder block sub-assembly with the 4 bolts.
16620
21.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
| *1 | Cylinder Block Sub-assembly |
| *2 | V-ribbed Belt Tensioner |
Install the V-ribbed belt tensioner assembly to the cylinder block sub-assembly with the 4 bolts.
Firmly press and hold the V-ribbed belt tensioner assembly against the cylinder block sub-assembly to eliminate any gaps in the areas labeled A in the illustration. Then uniformly tighten the 4 bolts.
12511C
22.INSTALL GENERATOR BRACKET
Install the generator bracket with the bolt.
27020
23.INSTALL GENERATOR ASSEMBLY
88440D
24.INSTALL NO. 2 IDLE PULLEY ASSEMBLY
25.INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER
12278
26.INSTALL VENTILATION HOSE HEAT INSULATOR
Install the ventilation hose heat insulator to the cylinder head sub-assembly with the 2 bolts.
13408
27.INSTALL CRANKSHAFT PULLEY SUB-ASSEMBLY
13505
28.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
13568
29.INSTALL TIMING BELT
11322A
30.INSTALL NO. 1 TIMING BELT COVER