Home › Drivetrain › R151 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › from 2016.01
RM3250E _52 Drivetrain _038033 R151 MANUAL TRANSMISSION / TRANSAXLE _0185596 MANUAL TRANSMISSION ASSEMBLY A

R151 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C325404N01
1.229,0.344 1.688,0.542 0.458,0.198 10 false (A) 1.5,0.156 1.958,0.354 0.458,0.198 10 false (B) 2.979,0.323 3.323,0.542 0.344,0.219 10 false (C)

except 1TR-FE, 2TR-FE:

Install the 3 wire harness clamp brackets to the manual transmission unit sub-assembly with the 3 bolts.

Torque:
for bolt A : 12.6 N*m (128 kgf*cm, 9 ft.*lbf)
for bolt B : 64 N*m (653 kgf*cm, 47 ft.*lbf)
for bolt C : 37 N*m (377 kgf*cm, 27 ft.*lbf)


b.
C325405N01
1.583,0.104 1.938,0.365 0.354,0.26 10 false (A) 3.083,0.313 3.385,0.573 0.302,0.26 10 false (B)

for 1TR-FE, 2TR-FE:

Install the 2 wire harness clamp brackets to the manual transmission unit sub-assembly with the 2 bolts.

Torque:
for bolt A : 64 N*m (653 kgf*cm, 47 ft.*lbf)
for bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33019C 2.INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C325673

Connect the 2 clamps and install the transmission breather sub-assembly.


Hide 33030 3.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

CAUTION:

The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


a.

Make sure that the knock pins are not loose, bent, damaged or scratched.


b.

Operate the transmission jack and install the manual transmission unit assembly to the vehicle.

CAUTION:

Do not raise the manual transmission unit assembly more than necessary. If the manual transmission unit assembly is raised excessively, the vehicle may also be lifted up.


NOTICE:

Make sure that the manual transmission unit assembly is clear of all wiring and hoses.



c.

Align the input shaft with the clutch disc and install the manual transmission unit assembly to the engine.


d.
C325683C04
2.844,1.5 2.917,1.25 2.917,1.25 3,1.25 false 0.125,0.094 0.438,0.292 0.313,0.198 10 false *A 0.125,2.427 0.438,2.625 0.313,0.198 10 false *B 0.635,0.052 0.792,0.25 0.156,0.198 10 false a 1.625,0.156 1.781,0.354 0.156,0.198 10 false a 0.083,0.781 0.24,0.979 0.156,0.198 10 false a 0.063,1.448 0.219,1.646 0.156,0.198 10 false b 0.292,1.75 0.448,1.948 0.156,0.198 10 false b 1.656,1.823 1.813,2.021 0.156,0.198 10 false b 1.896,1.667 2.052,1.865 0.156,0.198 10 false b 3.021,1.167 3.333,1.365 0.313,0.198 10 false *1
*A for 1TR-FE, 2TR-FE:
*B except 1TR-FE, 2TR-FE:
*1 Transmission Breather Bracket


for 1TR-FE, 2TR-FE:

Install the transmission breather bracket and 7 bolts.

Torque:
for bolt a : 71.5 N*m (729 kgf*cm, 53 ft.*lbf)
for bolt b : 37.2 N*m (379 kgf*cm, 27 ft.*lbf)


e.

except 1TR-FE, 2TR-FE:

Install the transmission breather bracket and 5 bolts.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 4.INSTALL STIFFENER PLATE (except 1TR-FE, 2TR-FE)

a.

Install the No. 2 rear end plate.


b.

for 1GD-FTV, 2GD-FTV:

i.

Install the stiffener plate RH with the 4 bolts and connect the wire harness.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


ii.

Install the stiffener plate LH with the 4 bolts.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)



c.

for 2KD-FTV:

i.

Install the stiffener plate RH with the 4 bolts.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


ii.

Install the stiffener plate LH with the 4 bolts.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)



d.

Install the No. 4 cylinder block insulator.


Hide 17118 5.INSTALL MANIFOLD STAY (for 1TR-FE, 2TR-FE)

Hide 12371A 6.INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 51204 7.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

Torque:
57 N*m (581 kgf*cm, 42 ft.*lbf)


b.

Connect the No. 3 frame crossmember sub-assembly to the rear engine mounting insulator.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 28100 8.INSTALL STARTER ASSEMBLY (for 1GD-FTV)

Hide 28100 9.INSTALL STARTER ASSEMBLY (for 2GD-FTV)

Hide 28100 10.INSTALL STARTER ASSEMBLY (for 1TR-FE)

Hide 28100 11.INSTALL STARTER ASSEMBLY (for 2TR-FE)

Hide 28100 12.INSTALL STARTER ASSEMBLY (for 2KD-FTV)

Hide 13.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

a.

Install the clutch release cylinder assembly with the 2 bolts.

Torque:
11.7 N*m (119 kgf*cm, 9 ft.*lbf)


Hide 14.CONNECT WIRE HARNESS

a.
C325676

Connect the 2 clamps and connector.


b.
C325671

Connect the ground cable with the bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 51203 17.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY (for 2WD)

a.

Install the No. 2 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 51407A 19.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre-Runner)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51442 20.INSTALL NO. 2 ENGINE UNDER COVER (for Pre-Runner)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51410 21.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for Pre-Runner)

Torque:
for M6 bolt : 11.5 N*m (117 kgf*cm, 8 ft.*lbf)
for M8 bolt : 28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51441 22.INSTALL NO. 1 ENGINE UNDER COVER (for 2WD)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51410 23.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for 2WD)

Torque:
for M8 bolt : 28 N*m (286 kgf*cm, 21 ft.*lbf)
for M10 bolt : 50 N*m (510 kgf*cm, 37 ft.*lbf)

Hide 33530F 24.INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY

a.
C333520C01
1.813,1.719 1.948,1.896 0.135,0.177 10 false -
V100135

MP grease


Apply MP grease to the tip of the shift lever.


b.
C329000C02
1.958,0.688 2.323,0.333 2.323,0.333 2.479,0.333 true 1.146,0.24 1.354,0.458 0.208,0.219 10 false *a 1.75,2.906 1.938,3.083 0.188,0.177 10 false *b 1.844,4.271 2.021,4.448 0.177,0.177 10 false *c 2.531,0.26 2.771,0.5 0.24,0.24 10 false *1
*1 Shift Lever Cap
*a Press down
*b Clockwise
*c Lock


Cover the shift lever cap with a cloth.


c.

While pressing down on the shift lever cap, turn it clockwise to install the shift lever assembly.


d.

Attach the shift lever cap boot.


Hide 58280A 25.INSTALL SHIFT LEVER BOOT ASSEMBLY

a.

Install the shift lever boot assembly with the 6 screws and 4 clips.


b.

Install the shift lever cover.


Hide 58810J 26.INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58811A 27.INSTALL FRONT CONSOLE BOX (w/o Console Box Lid)

Hide 28.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION