Home › Engine / Hybrid System › 5L-E LUBRICATION › OIL PUMP › from 2016.01
RM3250E _51 Engine / Hybrid System _049916 5L-E LUBRICATION _0244989 OIL PUMP A

5L-E LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11301 1.INSTALL TIMING BELT CASE SUB-ASSEMBLY

a.

Place a new gasket on the cylinder block sub-assembly.


b.

Install the timing belt case sub-assembly to the cylinder block sub-assembly with the 5 bolts.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)


Hide 15104 3.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer sub-assembly to the cylinder block sub-assembly with the 2 bolts and 2 nuts.

Torque:
for bolt : 18 N*m (184 kgf*cm, 13 ft.*lbf)
for nut : 21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12101 4.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old packing (FIPG) material and do not drop any oil on the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.

·

Using a gasket scraper, remove all the old packing (FIPG) material from the installation surface.

·

Thoroughly clean all components to remove all the loose material.

·

Using a non-residue solvent, clean both of the sealing surfaces.


NOTICE:

Do not use a solvent which will affect the painted surfaces.



b.
A227429C01
3.25,1.458 3.25,1.354 3.25,1.354 2.771,1.021 true 0.188,1.458 0.188,1.302 0.188,1.302 0.656,1.031 true 1.875,0.438 2.063,0.25 2.063,0.25 2.198,0.25 true 1.115,2.385 1.302,2.198 1.302,2.198 1.438,2.198 false 2.323,2.396 2.51,2.208 2.51,2.208 2.656,2.208 false 2.177,1.063 2.292,1.198 0.115,0.135 10 false B 1.083,1.063 1.208,1.208 0.125,0.146 10 false A 1.083,1.792 1.208,1.938 0.125,0.146 10 false A 2.177,1.792 2.333,1.958 0.156,0.167 10 false B 1.021,2.958 1.365,3.115 0.344,0.156 10 false A - A 2.156,2.958 2.5,3.115 0.344,0.156 10 false B - B 0.104,1.51 0.281,1.667 0.177,0.156 10 false *a 3.167,1.51 3.344,1.667 0.177,0.156 10 false *b 2.219,0.156 2.375,0.313 0.156,0.156 10 false *1 1.49,2.094 1.646,2.25 0.156,0.156 10 false *1 2.698,2.115 2.854,2.271 0.156,0.156 10 false *1
*1 Seal Packing
*a Timing Belt Case Contact Portion
*b Rear Oil Seal Retainer Contact Portion


Apply seal packing to the oil pan sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Item Seal Packing Diameter Seal Packing Application Length
Dashed line 7.0 mm (0.276 in.) 128 mm (5.04 in.)
Continuous line 5.0 mm (0.197 in.) -

HINT:
·

Do not apply an excessive amount to the surface, especially near the oil passages.

·

Parts must be assembled within 5 minutes of application. Otherwise the material must be removed and reapplied.




c.

Install the oil pan sub-assembly with the 16 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several steps.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13502 6.INSTALL NO. 2 TIMING BELT IDLER SUB-ASSEMBLY

Hide 13505 7.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 16100 8.INSTALL WATER PUMP ASSEMBLY

Hide 11322B 9.INSTALL NO. 2 TIMING BELT COVER

Hide 13523P 10.INSTALL CAMSHAFT TIMING PULLEY

Hide 12311 11.INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET RH

Hide 16333 14.INSTALL WATER OUTLET HOUSING

Hide 88431 15.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 22100 16.INSTALL INJECTION PUMP ASSEMBLY