Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Starter Signal Circuit  


DESCRIPTION

By using the starter delay circuit, the engine stop and start ECU can activate the ST NO. 2 relay (for starter motor operation) after activating the ST NO. 1 relay (for starter pinion operation) to operate the starter assembly.

WIRING DIAGRAM

for Automatic Transmission:



A382127E02
0.073,0.073 2.625,0.313 2.552,0.24 12 false w/ Entry and Start System: 0.208,8.052 0.417,8.25 0.208,0.198 10 false A 0.573,7.708 1.219,7.917 0.646,0.208 10 false SMART 1.417,7.542 1.792,7.75 0.375,0.208 10 false G69 2.073,6.344 2.448,6.552 0.375,0.208 10 false G69 2.677,6.958 3.052,7.167 0.375,0.208 10 false G70 2.677,7.479 3.052,7.688 0.375,0.208 10 false G70 1.792,7.552 2.167,7.76 0.375,0.208 10 false +B 2.052,6.573 2.469,6.781 0.417,0.208 10 false IG1D 2.198,6.969 2.688,7.177 0.49,0.208 10 false STAR 2.271,7.49 2.646,7.698 0.375,0.208 10 false STA 1.75,7.938 3.313,8.458 1.563,0.521 10 false Certification ECU (Smart Key ECU Assembly) 3.625,7.688 5.188,8.208 1.563,0.521 10 false Park/Neutral Position Switch Assembly 3.604,7.51 3.979,7.719 0.375,0.208 10 false C24 3.479,7.063 3.854,7.271 0.375,0.208 10 false 4 4.438,6.844 4.813,7.052 0.375,0.208 10 false 5 3.719,6.948 4.094,7.156 0.375,0.208 10 false B 3.719,6.688 4.094,6.896 0.375,0.208 10 false L 4.958,7.292 5.167,7.49 0.208,0.198 10 false D 5.344,7.281 5.552,7.479 0.208,0.198 10 false E 5.677,6.698 6.052,6.906 0.375,0.208 10 false G126 6.083,6.698 6.458,6.906 0.375,0.208 10 false STA 5.667,6.115 6.042,6.323 0.375,0.208 10 false G126 2.729,7.271 3.104,7.479 0.375,0.208 10 false 37 2.719,6.75 3.094,6.958 0.375,0.208 10 false 16 2.427,6.333 2.802,6.542 0.375,0.208 10 false 20 1.49,7.333 1.865,7.542 0.375,0.208 10 false 1 1.375,5.958 2.427,6.156 1.052,0.198 10 false IG1 NO. 1 1.021,5.594 1.396,5.802 0.375,0.208 10 false 1 0.75,5.594 1.125,5.802 0.375,0.208 10 false 3 0.74,6.365 1.115,6.573 0.375,0.208 10 false 5 1.021,6.365 1.396,6.573 0.375,0.208 10 false 2 4.938,5.844 5.99,6.042 1.052,0.198 10 false IG2 6.083,6.125 6.458,6.333 0.375,0.208 10 false CLL 5.75,5.906 6.125,6.115 0.375,0.208 10 false 17 5.771,6.469 6.146,6.677 0.375,0.208 10 false 21 2.135,4.875 4.979,5.094 2.844,0.219 10 false Instrument Panel Junction Block Assembly 4.625,5.688 5,5.896 0.375,0.208 10 false 1 5.375,5.688 5.75,5.896 0.375,0.208 10 false 2 4.625,5.375 5,5.583 0.375,0.208 10 false 3 5.365,5.365 5.74,5.573 0.375,0.208 10 false 5 0.354,2.083 1.406,2.281 1.052,0.198 10 false J/B-B 1.771,0.99 2.083,1.177 0.313,0.188 10 false 2B 1.781,1.417 2.094,1.604 0.313,0.188 10 false 2J 1.781,2.563 2.094,2.75 0.313,0.188 10 false 2K 1.781,3.125 2.094,3.313 0.313,0.188 10 false 2E 1.771,3.531 2.083,3.719 0.313,0.188 10 false 2G 1.771,3.99 2.083,4.177 0.313,0.188 10 false 2F 1.802,3.771 2.177,3.979 0.375,0.208 10 false 2 1.813,3.323 2.188,3.531 0.375,0.208 10 false 1 1.813,2.896 2.188,3.104 0.375,0.208 10 false 1 1.813,2.333 2.188,2.542 0.375,0.208 10 false 3 1.781,0.76 2.156,0.969 0.375,0.208 10 false 1 1.823,1.208 2.198,1.417 0.375,0.208 10 false 5 2.354,1.156 3.51,1.385 1.156,0.229 10 false EFI-MAIN NO. 2 3.208,1.667 4.365,1.896 1.156,0.229 10 false EFI-MAIN NO. 2 4.229,1.146 5.385,1.375 1.156,0.229 10 false EFI NO. 1 2.438,2.313 3.594,2.542 1.156,0.229 10 false EFI-MAIN NO. 1 3.458,2.813 4.615,3.042 1.156,0.229 10 false EFI-MAIN NO. 1 3.375,3.281 4.531,3.51 1.156,0.229 10 false IG1 NO. 3 2.958,3.688 4.115,3.917 1.156,0.229 10 false METER 3.75,4.156 4.906,4.385 1.156,0.229 10 false AM1 2.76,4.583 3.917,4.813 1.156,0.229 10 false AM2 NO. 2 5.625,2.573 5.833,2.771 0.208,0.198 10 false C 5.552,4 5.76,4.198 0.208,0.198 10 false B 4.969,0.979 5.281,1.167 0.313,0.188 10 false 2G 4.969,1.417 5.281,1.604 0.313,0.188 10 false 2P 4.969,2.156 5.281,2.344 0.313,0.188 10 false 2G 4.979,3.125 5.292,3.313 0.313,0.188 10 false 2C 5.01,0.771 5.385,0.979 0.375,0.208 10 false 3 5.01,1.208 5.385,1.417 0.375,0.208 10 false 9 5,1.917 5.375,2.125 0.375,0.208 10 false 7 4.979,2.563 5.292,2.75 0.313,0.188 10 false 2P 5.01,2.354 5.385,2.563 0.375,0.208 10 false 8 4.99,2.896 5.365,3.104 0.375,0.208 10 false 1 4.594,3.771 4.969,3.979 0.375,0.208 10 false 1*1 4.99,3.76 5.365,3.969 0.375,0.208 10 false 1*2 4.573,3.979 4.885,4.167 0.313,0.188 10 false 2R 4.969,3.99 5.281,4.177 0.313,0.188 10 false 2A 4.969,3.531 5.281,3.719 0.313,0.188 10 false 2P 4.979,4.427 5.292,4.615 0.313,0.188 10 false 2G 5,4.208 5.375,4.417 0.375,0.208 10 false 6 5.667,0.99 6.042,1.198 0.375,0.208 10 false G126 5.792,0.76 6.167,0.969 0.375,0.208 10 false 1 6.083,1 6.458,1.208 0.375,0.208 10 false +B 6.083,3.104 6.542,3.302 0.458,0.198 10 false IG1 6.094,3.542 6.552,3.74 0.458,0.198 10 false IG2 5.01,3.333 5.385,3.542 0.375,0.208 10 false 6 5.667,3.115 6.042,3.323 0.375,0.208 10 false G127 5.667,3.531 6.042,3.74 0.375,0.208 10 false G127 5.75,2.906 6.125,3.115 0.375,0.208 10 false 21 5.75,3.323 6.125,3.531 0.375,0.208 10 false 18 5.906,7.385 7.021,7.99 1.115,0.604 10 false Engine Stop and Start ECU 5.031,8.052 6.292,8.229 1.26,0.177 10 false *1: for RHD 5.052,8.365 6.313,8.542 1.26,0.177 10 false *2: for LHD

A382129E01
0.094,0.063 2.677,0.344 2.583,0.281 12 false w/o Entry and Start System: 0.208,8.052 0.365,8.25 0.156,0.198 10 false A 0.375,6.552 1.542,6.917 1.167,0.365 10 false STRG LOCK/AM2 NO. 2 1.823,7.021 3.354,7.406 1.531,0.385 10 false Ignition or Starter Switch Assembly 1.833,6.875 2.115,7.052 0.281,0.177 10 false G1 2.083,5.677 2.479,5.865 0.396,0.188 10 false AM1 2.083,6.281 2.479,6.469 0.396,0.188 10 false AM2 2.885,5.667 3.281,5.854 0.396,0.188 10 false IG1 2.865,6 3.26,6.188 0.396,0.188 10 false ST2 2.875,6.292 3.271,6.479 0.396,0.188 10 false IG2 4.01,7.115 4.406,7.302 0.396,0.188 10 false L 3.99,7.375 4.385,7.563 0.396,0.188 10 false B 5.177,7.521 5.573,7.708 0.396,0.188 10 false D 3.906,7.927 4.302,8.115 0.396,0.188 10 false C24 3.896,8.115 5.292,8.521 1.396,0.406 10 false Park/Neutral Position Switch Assembly 1.896,5.906 2.292,6.094 0.396,0.188 10 false 5 1.906,6.521 2.302,6.708 0.396,0.188 10 false 4 3.219,5.906 3.615,6.094 0.396,0.188 10 false 8 3.219,6.24 3.615,6.427 0.396,0.188 10 false 2 3.219,6.542 3.615,6.729 0.396,0.188 10 false 3 4.698,7.24 5.094,7.427 0.396,0.188 10 false 5 3.771,7.51 4.167,7.698 0.396,0.188 10 false 4 5.344,6.583 5.74,6.771 0.396,0.188 10 false E 2.042,4.448 4.792,4.708 2.75,0.26 10 false Instrument Panel Junction Block Assembly 0.333,2.354 1.01,2.542 0.677,0.188 10 false J/B-B 2.302,1.135 3.5,1.333 1.198,0.198 10 false EFI-MAIN NO. 2 3.146,1.656 4.344,1.854 1.198,0.198 10 false EFI-MAIN NO. 2 2.479,2.313 3.677,2.51 1.198,0.198 10 false EFI-MAIN NO. 1 3.458,2.823 4.656,3.021 1.198,0.198 10 false EFI-MAIN NO. 1 4.229,1.156 5,1.354 0.771,0.198 10 false EFI NO. 1 3.344,3.26 4.115,3.458 0.771,0.198 10 false IG1 NO. 3 2.948,3.688 3.719,3.885 0.771,0.198 10 false METER 3.75,4.146 4.521,4.344 0.771,0.198 10 false AM1 1.781,0.979 2.135,1.156 0.354,0.177 10 false 2B 1.792,1.406 2.146,1.583 0.354,0.177 10 false 2J 1.771,2.563 2.125,2.74 0.354,0.177 10 false 2K 1.781,3.115 2.135,3.292 0.354,0.177 10 false 2E 1.771,3.521 2.125,3.698 0.354,0.177 10 false 2G 1.771,3.99 2.125,4.167 0.354,0.177 10 false 2F 4.969,3.979 5.323,4.156 0.354,0.177 10 false 2A 4.969,3.531 5.323,3.708 0.354,0.177 10 false 2P 4.969,3.115 5.323,3.292 0.354,0.177 10 false 2C 4.958,2.573 5.313,2.75 0.354,0.177 10 false 2P 4.958,2.146 5.313,2.323 0.354,0.177 10 false 2G 4.969,1.417 5.323,1.594 0.354,0.177 10 false 2P 4.969,0.99 5.323,1.167 0.354,0.177 10 false 2G 5.667,0.99 6.146,1.188 0.479,0.198 10 false G126 5.667,7.125 6.156,7.344 0.49,0.219 10 false G126 5.667,3.531 6.167,3.708 0.5,0.177 10 false G127 5.667,3.115 6.167,3.292 0.5,0.177 10 false G127 1.833,0.781 2,0.969 0.167,0.188 10 false 1 1.823,1.219 2.219,1.406 0.396,0.188 10 false 5 1.833,2.344 2.229,2.531 0.396,0.188 10 false 3 1.823,3.781 2.219,3.969 0.396,0.188 10 false 2 1.823,2.896 1.99,3.083 0.167,0.188 10 false 1 1.823,3.323 1.99,3.51 0.167,0.188 10 false 1 5.01,0.771 5.406,0.958 0.396,0.188 10 false 3 5.021,1.219 5.417,1.406 0.396,0.188 10 false 9 5.01,1.927 5.406,2.115 0.396,0.188 10 false 7 5.021,2.365 5.417,2.552 0.396,0.188 10 false 8 5.01,2.896 5.406,3.083 0.396,0.188 10 false 1 5.031,3.333 5.427,3.521 0.396,0.188 10 false 6 5.021,3.771 5.417,3.958 0.396,0.188 10 false 1*2 5.625,2.573 6.021,2.76 0.396,0.188 10 false C 5.563,3.99 5.958,4.177 0.396,0.188 10 false B 6.104,1 6.583,1.198 0.479,0.198 10 false +B 6.094,3.115 6.594,3.292 0.5,0.177 10 false IG1 6.094,3.531 6.594,3.708 0.5,0.177 10 false IG2 6.083,7.125 6.573,7.344 0.49,0.219 10 false STA 5.375,7.854 7.125,8.094 1.75,0.24 10 false Engine Stop and Start ECU 5.781,0.771 6.177,0.958 0.396,0.188 10 false 1 5.75,2.906 6.146,3.094 0.396,0.188 10 false 21 5.74,3.323 6.135,3.51 0.396,0.188 10 false 18 5.76,6.906 6.156,7.094 0.396,0.188 10 false 21 4.573,3.979 4.927,4.156 0.354,0.177 10 false 2R 4.604,3.76 5,3.948 0.396,0.188 10 false 1*1 5.76,5.885 6.115,6.063 0.354,0.177 10 false 17 6.104,6.115 6.521,6.292 0.417,0.177 10 false CLL 1.26,8.198 2.198,8.396 0.938,0.198 10 false *1: for RHD 1.271,8.5 2.094,8.708 0.823,0.208 10 false *2: for LHD 5.667,6.104 6.156,6.323 0.49,0.219 10 false G126

A346917E02
0.302,0.104 0.458,0.302 0.156,0.198 10 false A 0.854,0.094 1.01,0.292 0.156,0.198 10 false B 3.354,6.052 3.51,6.25 0.156,0.198 10 false C 3.823,3.573 3.979,3.771 0.156,0.198 10 false D 1.677,2.625 2.896,2.865 1.219,0.24 10 false Starter Assembly 1.74,2.313 1.896,2.51 0.156,0.198 10 false B 0.667,7.375 1.74,7.573 1.073,0.198 10 false Battery 2.427,2.219 2.885,2.417 0.458,0.198 10 false SL1 2.427,1.74 2.885,1.938 0.458,0.198 10 false SL2 1.917,1.531 2.188,1.729 0.271,0.198 10 false ST 4.073,2.375 4.792,2.594 0.719,0.219 10 false ST NO. 2 3.906,1.594 4.063,1.792 0.156,0.198 10 false 3 4.708,1.604 4.865,1.802 0.156,0.198 10 false 5 3.906,1.938 4.104,2.125 0.198,0.188 10 false 1 4.698,1.938 4.875,2.125 0.177,0.188 10 false 2 6.021,2.031 6.635,2.229 0.615,0.198 10 false STA2 5.573,2.042 6.031,2.24 0.458,0.198 10 false G126 5.677,1.833 5.99,2.031 0.313,0.198 10 false 23 3.74,0.583 4.969,0.781 1.229,0.198 10 false ST NO. 2 2.385,5.729 2.844,5.927 0.458,0.198 10 false STA 2.281,6.063 2.896,6.26 0.615,0.198 10 false MREL 2.281,6.479 2.896,6.677 0.615,0.198 10 false CANH 6,6.5 6.615,6.698 0.615,0.198 10 false CANH 2.292,7 2.906,7.198 0.615,0.198 10 false CANL 6.021,7 6.635,7.198 0.615,0.198 10 false CANL 2.281,7.333 2.74,7.531 0.458,0.198 10 false NSW 3.365,7.344 3.521,7.542 0.156,0.198 10 false E 0.292,8.469 3.958,8.667 3.667,0.198 10 false : CAN Communication Line 1.906,7.979 2.365,8.177 0.458,0.198 10 false ECM 5.302,7.531 7.042,7.771 1.74,0.24 10 false Engine Stop and Start ECU 6.031,3.615 6.646,3.813 0.615,0.198 10 false GND1 6.01,2.75 6.625,2.948 0.615,0.198 10 false GND2 6,5.667 6.615,5.865 0.615,0.198 10 false DGND 5.563,5.656 6.021,5.854 0.458,0.198 10 false G126 5.698,5.438 5.854,5.635 0.156,0.198 10 false 6 5.573,2.76 6.031,2.958 0.458,0.198 10 false G125 5.698,3.406 5.854,3.604 0.156,0.198 10 false 8 5.573,3.625 6.031,3.823 0.458,0.198 10 false G125 5.688,2.563 5.844,2.76 0.156,0.198 10 false 2 5.563,6.5 6.021,6.698 0.458,0.198 10 false G127 5.656,6.292 5.969,6.49 0.313,0.198 10 false 13 5.563,7 6.021,7.198 0.458,0.198 10 false G127 5.656,6.802 5.969,7 0.313,0.198 10 false 14 2.281,3.938 3,4.156 0.719,0.219 10 false ST NO. 1 1.344,3.417 2.063,3.635 0.719,0.219 10 false ST NO. 1 1.01,0.552 1.469,0.75 0.458,0.198 10 false ALT 5.563,4.938 6.021,5.135 0.458,0.198 10 false G125 5.563,4.313 6.021,4.51 0.458,0.198 10 false G125 6.042,4.938 6.656,5.135 0.615,0.198 10 false BIN1 5.688,4.729 5.844,4.927 0.156,0.198 10 false 3 6.031,4.302 6.646,4.5 0.615,0.198 10 false BIN2 5.677,4.083 5.854,4.26 0.177,0.177 10 false 1 3.51,4.469 4.333,4.677 0.823,0.208 10 false BBC NO. 1 2.792,5.115 3.615,5.323 0.823,0.208 10 false BBC NO. 3 2.146,3.448 2.292,3.76 0.146,0.313 10 false 1 2.948,3.146 3.104,3.344 0.156,0.198 10 false 3 2.156,3.125 2.313,3.323 0.156,0.198 10 false 5 2.948,3.458 3.125,3.646 0.177,0.188 10 false 2 1.854,1.292 2.313,1.49 0.458,0.198 10 false C140 2.271,1.281 2.469,1.469 0.198,0.188 10 false 1 2.74,1.719 3.198,1.917 0.458,0.198 10 false C141 2.865,1.5 3.042,1.688 0.177,0.188 10 false 2 2.74,2.177 3.198,2.375 0.458,0.198 10 false C141 2.854,1.969 3.052,2.156 0.198,0.188 10 false 1 1.406,2.302 1.865,2.5 0.458,0.198 10 false D3 1.438,2.083 1.635,2.271 0.198,0.188 10 false 1 0.458,5.854 1.531,6.052 1.073,0.198 10 false FL MAIN 2.771,5.625 3.083,5.823 0.313,0.198 10 false 22 2.771,5.948 3.083,6.146 0.313,0.198 10 false 14 2.771,6.302 3.083,6.5 0.313,0.198 10 false 17 2.771,6.802 3.083,7 0.313,0.198 10 false 28 2.76,7.219 3.073,7.417 0.313,0.198 10 false 11 1.906,7.771 2.365,7.969 0.458,0.198 10 false G85

for Manual Transmission:



A382128E01
0.073,0.063 2.625,0.313 2.552,0.25 12 false w/ Entry and Start System: 0.208,8.052 0.365,8.25 0.156,0.198 10 false A 3.74,7.302 4.052,7.5 0.313,0.198 10 false B2 3.74,7.469 4.813,8.01 1.073,0.542 10 false Clutch Start Switch Assembly (for Lower) 3.708,7.073 4.021,7.271 0.313,0.198 10 false 2 4.531,7.083 4.844,7.281 0.313,0.198 10 false 1 1.615,7.917 2.792,8.479 1.177,0.563 10 false Certification ECU (Smart Key ECU Assembly) 1.417,7.552 1.802,7.75 0.385,0.198 10 false G69 2.052,6.344 2.438,6.542 0.385,0.198 10 false G69 2.667,6.958 3.052,7.156 0.385,0.198 10 false G70 2.667,7.479 3.052,7.677 0.385,0.198 10 false G70 1.802,7.552 2.188,7.75 0.385,0.198 10 false +B 2.042,6.563 2.479,6.76 0.438,0.198 10 false IG1D 2.188,6.958 2.76,7.188 0.573,0.229 10 false STAR 2.25,7.479 2.635,7.677 0.385,0.198 10 false STA 2.729,7.271 3.042,7.469 0.313,0.198 10 false 37 2.729,6.771 3.042,6.969 0.313,0.198 10 false 16 2.438,6.344 2.75,6.542 0.313,0.198 10 false 20 1.521,7.333 1.833,7.531 0.313,0.198 10 false 1 1.031,5.594 1.344,5.792 0.313,0.198 10 false 1 0.76,5.583 1.073,5.781 0.313,0.198 10 false 3 0.75,6.365 1.063,6.563 0.313,0.198 10 false 5 1.031,6.365 1.344,6.563 0.313,0.198 10 false 2 0.542,7.708 1.125,7.896 0.583,0.188 10 false SMART 4.927,5.844 5.313,6.052 0.385,0.208 10 false IG2 4.615,5.677 4.927,5.875 0.313,0.198 10 false 1 4.625,5.375 4.938,5.573 0.313,0.198 10 false 3 5.365,5.365 5.677,5.563 0.313,0.198 10 false 5 5.375,5.677 5.688,5.875 0.313,0.198 10 false 2 1.823,4.875 4.719,5.135 2.896,0.26 10 false Instrument Panel Junction Block Assembly 4.958,7.563 5.115,7.76 0.156,0.198 10 false D 5.344,7.563 5.5,7.76 0.156,0.198 10 false E 5.563,4 5.719,4.198 0.156,0.198 10 false B 5.615,2.573 5.771,2.771 0.156,0.198 10 false C 0.344,2.094 0.927,2.281 0.583,0.188 10 false J/B-B 2.333,1.146 3.417,1.354 1.083,0.208 10 false EFI-MAIN NO. 2 3.177,1.677 4.26,1.885 1.083,0.208 10 false EFI-MAIN NO. 2 2.479,2.302 3.563,2.51 1.083,0.208 10 false EFI-MAIN NO. 1 3.448,2.823 4.531,3.031 1.083,0.208 10 false EFI-MAIN NO. 1 4.167,1.156 4.917,1.396 0.75,0.24 10 false EFI NO. 1 3.385,3.26 4.469,3.469 1.083,0.208 10 false IG1 NO. 3 2.927,3.688 4.01,3.896 1.083,0.208 10 false METER 3.74,4.146 4.26,4.375 0.521,0.229 10 false AM1 2.75,4.573 3.833,4.781 1.083,0.208 10 false AM2 NO. 2 1.771,0.99 2.354,1.177 0.583,0.188 10 false 2B 1.781,1.406 2.365,1.594 0.583,0.188 10 false 2J 1.781,2.552 2.365,2.74 0.583,0.188 10 false 2K 1.792,3.115 2.375,3.302 0.583,0.188 10 false 2E 1.771,3.531 2.354,3.719 0.583,0.188 10 false 2G 1.771,3.99 2.354,4.177 0.583,0.188 10 false 2F 4.969,4.427 5.552,4.615 0.583,0.188 10 false 2G 4.979,3.99 5.563,4.177 0.583,0.188 10 false 2A 4.979,3.542 5.563,3.729 0.583,0.188 10 false 2P 4.979,3.115 5.563,3.302 0.583,0.188 10 false 2C 4.958,2.156 5.542,2.344 0.583,0.188 10 false 2G 4.969,2.563 5.552,2.75 0.583,0.188 10 false 2P 4.979,1.417 5.563,1.604 0.583,0.188 10 false 2P 4.958,0.99 5.542,1.177 0.583,0.188 10 false 2G 5.677,1 6.26,1.188 0.583,0.188 10 false G126 5.677,3.115 6.26,3.302 0.583,0.188 10 false G127 5.677,3.531 6.26,3.719 0.583,0.188 10 false G127 5.667,6.125 6.25,6.313 0.583,0.188 10 false G126 5.667,6.969 6.25,7.156 0.583,0.188 10 false G126 6.094,1 6.677,1.188 0.583,0.188 10 false +B 6.094,3.115 6.677,3.302 0.583,0.188 10 false IG1 6.094,3.531 6.677,3.719 0.583,0.188 10 false IG2 6.083,6.115 6.667,6.302 0.583,0.188 10 false CLL 6.083,6.969 6.667,7.156 0.583,0.188 10 false STA 5.792,0.771 6.104,0.969 0.313,0.198 10 false 1 5.021,2.896 5.333,3.094 0.313,0.198 10 false 1 4.99,3.771 5.302,3.969 0.313,0.198 10 false 1*2 1.823,3.333 2.135,3.531 0.313,0.198 10 false 1 1.813,0.76 2.125,0.958 0.313,0.198 10 false 1 1.833,1.208 2.146,1.406 0.313,0.198 10 false 5 1.823,2.885 2.135,3.083 0.313,0.198 10 false 1 1.833,2.333 2.146,2.531 0.313,0.198 10 false 3 1.823,3.771 2.135,3.969 0.313,0.198 10 false 2 5.01,0.781 5.323,0.979 0.313,0.198 10 false 3 5.01,1.219 5.323,1.417 0.313,0.198 10 false 9 5.01,1.938 5.323,2.135 0.313,0.198 10 false 7 5,2.375 5.313,2.573 0.313,0.198 10 false 8 5.01,3.323 5.323,3.521 0.313,0.198 10 false 6 5.021,4.229 5.333,4.427 0.313,0.198 10 false 6 5.76,3.344 6.073,3.542 0.313,0.198 10 false 18 5.771,2.917 6.083,3.115 0.313,0.198 10 false 21 5.771,6.75 6.083,6.948 0.313,0.198 10 false 21 5.771,5.896 6.083,6.094 0.313,0.198 10 false 17 5.656,7.656 7.073,8.031 1.417,0.375 10 false Engine Stop and Start ECU 4.573,3.979 5.156,4.167 0.583,0.188 10 false 2R 4.604,3.771 4.917,3.969 0.313,0.198 10 false 1*1 4.656,8.083 5.625,8.271 0.969,0.188 10 false *1: for RHD 4.677,8.438 5.646,8.625 0.969,0.188 10 false *2: for LHD 1.375,5.948 2.396,6.156 1.021,0.208 10 false IG1 NO. 1

A382130E01
0.083,0.073 2.74,0.344 2.656,0.271 12 false w/o Entry and Start System: 0.198,8.073 0.406,8.292 0.208,0.219 10 false A 5.177,7.531 5.385,7.75 0.208,0.219 10 false D 5.344,6.583 5.552,6.802 0.208,0.219 10 false E 5.563,4 5.771,4.219 0.208,0.219 10 false B 5.625,2.583 5.833,2.802 0.208,0.219 10 false C 1.99,7 3.417,7.385 1.427,0.385 10 false Ignition or Starter Switch Assembly 2,6.823 2.396,7.021 0.396,0.198 10 false G1 2.094,5.688 2.49,5.885 0.396,0.198 10 false AM1 2.083,6.271 2.479,6.469 0.396,0.198 10 false AM2 2.865,5.667 3.26,5.865 0.396,0.198 10 false IG1 2.833,5.99 3.229,6.188 0.396,0.198 10 false ST2 2.875,6.292 3.271,6.49 0.396,0.198 10 false IG2 1.844,5.906 2.052,6.125 0.208,0.219 10 false 5 1.833,6.531 2.042,6.75 0.208,0.219 10 false 4 3.208,5.885 3.417,6.104 0.208,0.219 10 false 8 3.208,6.229 3.417,6.448 0.208,0.219 10 false 2 3.219,6.531 3.427,6.75 0.208,0.219 10 false 3 4.531,7.25 4.74,7.469 0.208,0.219 10 false 1 3.677,7.24 3.885,7.458 0.208,0.219 10 false 2 3.75,7.5 3.958,7.719 0.208,0.219 10 false B2 0.469,6.563 1.625,7.042 1.156,0.479 10 false STRG LOCK/AM2 NO. 2 5.656,7.833 7.083,8.219 1.427,0.385 10 false Engine Stop and Start ECU 3.729,7.656 5.156,8.042 1.427,0.385 10 false Clutch Start Switch Assembly (for Lower) 1.802,4.448 4.958,4.677 3.156,0.229 10 false Instrument Panel Junction Block Assembly 0.344,2.365 1.156,2.583 0.813,0.219 10 false J/B-B 1.781,0.99 2.135,1.208 0.354,0.219 10 false 2B 2.292,1.135 3.406,1.323 1.115,0.188 10 false EFI-MAIN NO. 2 3.188,1.656 4.302,1.844 1.115,0.188 10 false EFI-MAIN NO. 2 3.427,2.813 4.542,3 1.115,0.188 10 false EFI-MAIN NO. 1 2.479,2.313 3.594,2.5 1.115,0.188 10 false EFI-MAIN NO. 1 4.188,1.156 5.021,1.396 0.833,0.24 10 false EFI NO. 1 3.354,3.271 4.469,3.458 1.115,0.188 10 false IG1 NO. 3 2.938,3.698 4.052,3.885 1.115,0.188 10 false METER 3.75,4.135 4.198,4.344 0.448,0.208 10 false AM1 1.771,1.417 2.125,1.635 0.354,0.219 10 false 2J 1.781,2.563 2.135,2.781 0.354,0.219 10 false 2K 1.792,3.115 2.146,3.333 0.354,0.219 10 false 2E 1.771,3.531 2.125,3.75 0.354,0.219 10 false 2G 1.771,3.99 2.125,4.208 0.354,0.219 10 false 2F 4.99,3.99 5.344,4.208 0.354,0.219 10 false 2A 4.979,3.542 5.333,3.76 0.354,0.219 10 false 2P 4.979,3.125 5.333,3.344 0.354,0.219 10 false 2C 4.979,2.583 5.333,2.802 0.354,0.219 10 false 2P 4.969,1.417 5.323,1.635 0.354,0.219 10 false 2P 4.969,2.156 5.323,2.375 0.354,0.219 10 false 2G 4.969,0.99 5.323,1.208 0.354,0.219 10 false 2G 1.813,0.76 2.021,0.979 0.208,0.219 10 false 1 1.813,1.198 2.021,1.417 0.208,0.219 10 false 5 1.833,2.333 2.042,2.552 0.208,0.219 10 false 3 1.833,2.906 2.042,3.125 0.208,0.219 10 false 1 1.823,3.344 2.031,3.563 0.208,0.219 10 false 1 1.823,3.781 2.031,4 0.208,0.219 10 false 2 5.031,0.771 5.24,0.99 0.208,0.219 10 false 3 5.021,1.219 5.229,1.438 0.208,0.219 10 false 9 5.021,1.927 5.229,2.146 0.208,0.219 10 false 7 5.021,2.375 5.229,2.594 0.208,0.219 10 false 8 5.031,2.885 5.24,3.104 0.208,0.219 10 false 1 4.969,3.792 5.448,4.052 0.479,0.26 10 false 1*2 5.021,3.344 5.229,3.563 0.208,0.219 10 false 6 5.667,0.99 6.021,1.208 0.354,0.219 10 false G126 5.677,3.115 6.031,3.333 0.354,0.219 10 false G127 5.677,3.531 6.031,3.75 0.354,0.219 10 false G127 5.677,6.115 6.031,6.333 0.354,0.219 10 false G126 5.76,6.885 5.969,7.104 0.208,0.219 10 false 21 5.75,3.333 5.958,3.552 0.208,0.219 10 false 18 5.771,2.896 5.979,3.115 0.208,0.219 10 false 21 5.792,0.76 6,0.979 0.208,0.219 10 false 1 6.083,7.125 6.531,7.344 0.448,0.219 10 false STA 6.094,3.542 6.542,3.76 0.448,0.219 10 false IG2 6.104,3.115 6.552,3.333 0.448,0.219 10 false IG1 6.094,1 6.448,1.219 0.354,0.219 10 false +B 4.583,3.979 4.938,4.198 0.354,0.219 10 false 2R 4.615,3.781 4.885,4 0.271,0.219 10 false 1*1 6.104,6.104 6.604,6.333 0.5,0.229 10 false CLL 5.76,5.906 6.115,6.125 0.354,0.219 10 false 17 1.219,7.969 2.219,8.167 1,0.198 10 false *1: for RHD 1.219,8.281 2.219,8.479 1,0.198 10 false *2: for LHD 5.667,7.125 6.021,7.344 0.354,0.219 10 false G126

A346917E02
0.302,0.104 0.458,0.302 0.156,0.198 10 false A 0.854,0.094 1.01,0.292 0.156,0.198 10 false B 3.354,6.052 3.51,6.25 0.156,0.198 10 false C 3.823,3.573 3.979,3.771 0.156,0.198 10 false D 1.677,2.625 2.896,2.865 1.219,0.24 10 false Starter Assembly 1.74,2.313 1.896,2.51 0.156,0.198 10 false B 0.667,7.375 1.74,7.573 1.073,0.198 10 false Battery 2.427,2.219 2.885,2.417 0.458,0.198 10 false SL1 2.427,1.74 2.885,1.938 0.458,0.198 10 false SL2 1.917,1.531 2.188,1.729 0.271,0.198 10 false ST 4.073,2.375 4.792,2.594 0.719,0.219 10 false ST NO. 2 3.906,1.594 4.063,1.792 0.156,0.198 10 false 3 4.708,1.604 4.865,1.802 0.156,0.198 10 false 5 3.906,1.938 4.104,2.125 0.198,0.188 10 false 1 4.698,1.938 4.875,2.125 0.177,0.188 10 false 2 6.021,2.031 6.635,2.229 0.615,0.198 10 false STA2 5.573,2.042 6.031,2.24 0.458,0.198 10 false G126 5.677,1.833 5.99,2.031 0.313,0.198 10 false 23 3.74,0.583 4.969,0.781 1.229,0.198 10 false ST NO. 2 2.385,5.729 2.844,5.927 0.458,0.198 10 false STA 2.281,6.063 2.896,6.26 0.615,0.198 10 false MREL 2.281,6.479 2.896,6.677 0.615,0.198 10 false CANH 6,6.5 6.615,6.698 0.615,0.198 10 false CANH 2.292,7 2.906,7.198 0.615,0.198 10 false CANL 6.021,7 6.635,7.198 0.615,0.198 10 false CANL 2.281,7.333 2.74,7.531 0.458,0.198 10 false NSW 3.365,7.344 3.521,7.542 0.156,0.198 10 false E 0.292,8.469 3.958,8.667 3.667,0.198 10 false : CAN Communication Line 1.906,7.979 2.365,8.177 0.458,0.198 10 false ECM 5.302,7.531 7.042,7.771 1.74,0.24 10 false Engine Stop and Start ECU 6.031,3.615 6.646,3.813 0.615,0.198 10 false GND1 6.01,2.75 6.625,2.948 0.615,0.198 10 false GND2 6,5.667 6.615,5.865 0.615,0.198 10 false DGND 5.563,5.656 6.021,5.854 0.458,0.198 10 false G126 5.698,5.438 5.854,5.635 0.156,0.198 10 false 6 5.573,2.76 6.031,2.958 0.458,0.198 10 false G125 5.698,3.406 5.854,3.604 0.156,0.198 10 false 8 5.573,3.625 6.031,3.823 0.458,0.198 10 false G125 5.688,2.563 5.844,2.76 0.156,0.198 10 false 2 5.563,6.5 6.021,6.698 0.458,0.198 10 false G127 5.656,6.292 5.969,6.49 0.313,0.198 10 false 13 5.563,7 6.021,7.198 0.458,0.198 10 false G127 5.656,6.802 5.969,7 0.313,0.198 10 false 14 2.281,3.938 3,4.156 0.719,0.219 10 false ST NO. 1 1.344,3.417 2.063,3.635 0.719,0.219 10 false ST NO. 1 1.01,0.552 1.469,0.75 0.458,0.198 10 false ALT 5.563,4.938 6.021,5.135 0.458,0.198 10 false G125 5.563,4.313 6.021,4.51 0.458,0.198 10 false G125 6.042,4.938 6.656,5.135 0.615,0.198 10 false BIN1 5.688,4.729 5.844,4.927 0.156,0.198 10 false 3 6.031,4.302 6.646,4.5 0.615,0.198 10 false BIN2 5.677,4.083 5.854,4.26 0.177,0.177 10 false 1 3.51,4.469 4.333,4.677 0.823,0.208 10 false BBC NO. 1 2.792,5.115 3.615,5.323 0.823,0.208 10 false BBC NO. 3 2.146,3.448 2.292,3.76 0.146,0.313 10 false 1 2.948,3.146 3.104,3.344 0.156,0.198 10 false 3 2.156,3.125 2.313,3.323 0.156,0.198 10 false 5 2.948,3.458 3.125,3.646 0.177,0.188 10 false 2 1.854,1.292 2.313,1.49 0.458,0.198 10 false C140 2.271,1.281 2.469,1.469 0.198,0.188 10 false 1 2.74,1.719 3.198,1.917 0.458,0.198 10 false C141 2.865,1.5 3.042,1.688 0.177,0.188 10 false 2 2.74,2.177 3.198,2.375 0.458,0.198 10 false C141 2.854,1.969 3.052,2.156 0.198,0.188 10 false 1 1.406,2.302 1.865,2.5 0.458,0.198 10 false D3 1.438,2.083 1.635,2.271 0.198,0.188 10 false 1 0.458,5.854 1.531,6.052 1.073,0.198 10 false FL MAIN 2.771,5.625 3.083,5.823 0.313,0.198 10 false 22 2.771,5.948 3.083,6.146 0.313,0.198 10 false 14 2.771,6.302 3.083,6.5 0.313,0.198 10 false 17 2.771,6.802 3.083,7 0.313,0.198 10 false 28 2.76,7.219 3.073,7.417 0.313,0.198 10 false 11 1.906,7.771 2.365,7.969 0.458,0.198 10 false G85

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for Automatic Transmission:

When the engine stop and start ECU is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CRANKING
a.

Turn the engine starts and check that the engine cranks.


Result:
Result Proceed to
Engine cranks A
Engine does not crank (for Automatic Transmission) B
Engine does not crank (for Manual Transmission) C



A

2.PERFORM ACTIVE TEST USING GTS (STARTER)

B

5.PERFORM ACTIVE TEST USING GTS (STARTER)

C

27.PERFORM ACTIVE TEST USING GTS (STARTER)
2.PERFORM ACTIVE TEST USING GTS (STARTER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter.

Powertrain > Stop and Start > Active Test
Tester Display
Starter
50004 227 7

e.

Check whether the engine cranks while the Active Test "Starter" is being performed.

NOTICE:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Proceed to
OK
NG



OK

GO TO DTC P1603 (CONFIRM CAUSE OF ENGINE STALL)

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
A346921C06
1,0.563 1.5,0.75 0.5,0.188 3.167,0.583 3.677,0.792 0.51,0.208 5.417,0.583 5.917,0.771 0.5,0.188 0.667,1.333 0.417,1.333 true 0.667,1.583 0.417,1.583 true 2.51,1.521 2.5,2.083 true 5.938,1.698 6,2.083 true 5.417,1.708 5.417,2.083 true 1.083,0.583 1.542,0.781 0.458,0.198 10 false G125 3.26,0.604 3.719,0.802 0.458,0.198 10 false G126 5.5,0.604 5.958,0.802 0.458,0.198 10 false G127 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.083,1.26 0.698,1.458 0.615,0.198 10 false BIN2 0.083,1.5 0.698,1.698 0.615,0.198 10 false BIN1 2.438,2.135 2.75,2.333 0.313,0.198 10 false +B 5.917,2.135 6.375,2.333 0.458,0.198 10 false IG1 5.323,2.135 5.781,2.333 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -


a.

Disconnect the G125, G126 and G127 engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G125-1 (BIN2) - Body ground Always 9.5 to 14 V
G125-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G126-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
G127-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
G127-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the G125 and G126 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G125-2 (GND2) - Body ground Always Below 1 Ω
G125-8 (GND1) - Body ground Always Below 1 Ω
G126-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING GTS (STARTER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter.

Powertrain > Stop and Start > Active Test
Tester Display
Starter
50004 227 7

e.

Check whether the engine cranks while the Active Test "Starter" is being performed.

NOTICE:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

6.READ VALUE USING GTS (NEUTRAL SWITCH)

B

15.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
6.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9
OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in P or N ON
Shift lever not in P or N OFF



Result:
Proceed to
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG



OK (w/ Entry and Start System)

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)

OK (w/o Entry and Start System)

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)
a.

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G126 engine stop and start ECU connector.


c.

Disconnect the C24 park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-16 (STAR) - G126-17 (CLL) Always Below 1 Ω
G70-16 (STAR) - Body ground Always 10 kΩ or higher
G126-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.
A288763C19
1.51,0.323 2.031,0.604 0.521,0.281 1.313,1.698 1.333,1.375 true 0.354,0.229 0.667,0.385 0.313,0.156 10 false *a 1.208,1.729 1.667,1.927 0.458,0.198 10 false CLL 1.604,0.396 2.063,0.594 0.458,0.198 10 false G126
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the G126 engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G126-17 (CLL) - Body ground Engine started using push start switch assembly (engine start) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
a.
A285192C08
1.5,0.625 1.865,0.875 0.365,0.25 2.25,1.99 2.833,2.083 2.833,2.083 2.833,2.25 true 0.302,0.281 0.615,0.479 0.313,0.198 10 false *a 1.583,0.688 2.042,0.885 0.458,0.198 10 false G1 2.698,2.302 3.156,2.5 0.458,0.198 10 false AM2
*a Front view of wire harness connector:
(to Ignition or Starter Switch Assembly)


Disconnect the G1 ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G1-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G1 ignition or starter switch assembly connector.


b.

Disconnect the C24 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (ST2) - C24-4 (B) Always Below 1 Ω
G1-2 (ST2) - Body ground Always 10 kΩ or higher
C24-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG



OK (w/ Entry and Start System)

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

OK (w/o Entry and Start System)

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)

NG

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-16 (STAR) - ST NO. 1 relay terminal 2 Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the G1 ignition or starter switch assembly connector.


b.

Disconnect the G126 engine stop and start ECU connectors.


c.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (ST2) - ST NO. 1 relay terminal 2 Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
a.

Connect an oscilloscope to terminals G126-21 (STA), G126-23 (STA2) and G126-6 (DGND).

A346331C98
3.188,0.615 3.708,0.844 0.521,0.229 4.167,0.583 4,0.583 4,0.583 3.75,1.208 true 3.427,1.344 3.354,2.208 true 3.271,1.323 2.313,2.281 false 3.281,0.656 3.74,0.854 0.458,0.198 10 false G126 4.219,0.51 4.833,0.708 0.615,0.198 10 false DGND 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 3.229,2.26 3.688,2.458 0.458,0.198 10 false STA 2.135,2.344 2.594,2.542 0.458,0.198 10 false STA2
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.
A285702E12
0.042,0.677 0.5,0.875 0.458,0.198 10 false STA 0.042,1.281 0.5,1.479 0.458,0.198 10 false STA2 1.156,1.781 3.146,1.979 1.99,0.198 10 false 0.03 to 0.06 seconds 0.031,0.854 1.865,1.052 1.833,0.198 10 false (ST NO. 1 Relay) 0.031,1.448 1.865,1.646 1.833,0.198 10 false (ST NO. 2 Relay)

Check the waveform immediately after turning the engine starts.

Item Condition
Tester Connection G126-21 (STA) - G126-6 (DGND)
G126-23 (STA2) - G126-6 (DGND)
Condition Engine started by ignition or starter switch assembly*1 or push start switch assembly*2 operation

*1: w/o Entry and Start System

*2: w/ Entry and Start System


Result:
Result Proceed to
Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: between 0.03 and 0.06 seconds A
Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: not between 0.03 and 0.06 seconds B
ST NO. 1 relay turns on and ST NO. 2 relay does not turn on C
ST NO. 1 relay and ST NO. 2 relay do not turn on D


NOTICE:

After replacing the engine stop and start ECU, make sure that the flywheel sub-assembly and starter pinion gear are not excessively worn. A malfunction in the delay circuit may cause the flywheel sub-assembly or starter pinion gear to be worn or damaged.




A

16.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)

B

C

25.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)

D

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
16.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BATTERY)

NG

REPLACE RELAY (ST NO. 1, ST NO. 2 RELAY)

17.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BATTERY)
a.
A348494C02
1.875,0.177 2.188,0.375 0.313,0.198 10 false *1 0.479,0.729 0.792,0.927 0.313,0.198 10 false *a 0.469,2.177 0.781,2.375 0.313,0.198 10 false *b
*1 Engine Room Relay Block and Junction Block
*a ST NO. 1 Relay Terminal
*b ST NO. 2 Relay Terminal


Remove the ST NO. 1 and ST NO. 2 relays from the engine room relay block and junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 5 - Body ground Always 9.5 to 14 V
ST NO. 2 relay terminal 5 - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 and ST NO. 2 relays from the engine room relay block and junction block.


b.

Disconnect the C141 starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 3 - C141-1 (SL1) Always Below 1 Ω
ST NO. 2 relay terminal 3 - C141-2 (SL2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)
a.

Remove the ST NO. 2 relay from the engine room relay block and junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


c.

w/ Entry and Start System:

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


d.

for Automatic Transmission:

Disconnect the C24 park/neutral position switch assembly connector.


e.

for Manual Transmission:

Disconnect the B2 clutch start switch assembly (for lower) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-21 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
G126-21 (STA) - Body ground Always 10 kΩ or higher
ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 2 RELAY)
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Remove the ST NO. 2 relay from the engine room relay block and junction block.


c.

Disconnect the G85 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-23 (STA2) - ST NO. 2 relay terminal 2 Always Below 1 Ω
G126-23 (STA2) - Body ground Always 10 kΩ or higher
ST NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK STARTER SIGNAL (OUTPUT WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK STARTER SIGNAL (OUTPUT WAVEFORM)
a.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter Motor Drive Magnet Switch.


b.

Connect the positive (+) lead of an oscilloscope to the positive (+) battery terminal and the negative (-) lead to the negative (-) battery terminal.


c.

While performing the Active Test "Starter Motor Drive Magnet Switch" to forcibly operate the starter motor, count the number of times the waveform drops.

NOTICE:
·

The Active Test "Starter Motor Drive Magnet Switch" is stopped automatically after the starter motor operates for 3 seconds.

·

Do not forcibly operate the starter pinion.



A285237E06
3.438,0.781 3.583,0.417 3.583,0.417 3.833,0.417 false 0.104,0.729 0.719,0.927 0.615,0.198 10 false Normal: 0.115,2.063 1.073,2.26 0.958,0.198 10 false Abnormal: 0.719,0.917 2.042,1.135 1.323,0.219 10 false Approximately 12 V 1.938,1.24 3.927,1.438 1.99,0.198 10 false 7.6 to 9.3 V* 3.906,0.323 5.667,0.542 1.76,0.219 10 false Approximately 0.1 seconds 3.396,1.698 5.073,1.896 1.677,0.198 10 false Less than 3 seconds 5.167,3.177 7.083,3.5 1.917,0.323 10 false *: Varies with battery condition 2.396,2.49 5.031,3.042 2.635,0.552 10 false If the waveform does not change either the starter inrush current reduction relay or starter assembly is not operating. 0.729,2.302 2.052,2.521 1.323,0.219 10 false Approximately 12 V

Standard:

Waveform drops 2 times


Result:
Number of Times Waveform Dropped Proceed to
0 times A
2 times B




A

B

24.INSPECT STARTER ASSEMBLY
24.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

25.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
A346921C06
1,0.563 1.5,0.75 0.5,0.188 3.167,0.583 3.677,0.792 0.51,0.208 5.417,0.583 5.917,0.771 0.5,0.188 0.667,1.333 0.417,1.333 true 0.667,1.583 0.417,1.583 true 2.51,1.521 2.5,2.083 true 5.938,1.698 6,2.083 true 5.417,1.708 5.417,2.083 true 1.083,0.583 1.542,0.781 0.458,0.198 10 false G125 3.26,0.604 3.719,0.802 0.458,0.198 10 false G126 5.5,0.604 5.958,0.802 0.458,0.198 10 false G127 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.083,1.26 0.698,1.458 0.615,0.198 10 false BIN2 0.083,1.5 0.698,1.698 0.615,0.198 10 false BIN1 2.438,2.135 2.75,2.333 0.313,0.198 10 false +B 5.917,2.135 6.375,2.333 0.458,0.198 10 false IG1 5.323,2.135 5.781,2.333 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -


a.

Disconnect the G125, G126 and G127 engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G125-1 (BIN2) - Body ground Always 9.5 to 14 V
G125-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G126-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
G127-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
G127-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the G125 and G126 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G125-2 (GND2) - Body ground Always Below 1 Ω
G125-8 (GND1) - Body ground Always Below 1 Ω
G126-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.PERFORM ACTIVE TEST USING GTS (STARTER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter.

Powertrain > Stop and Start > Active Test
Tester Display
Starter
50004 227 7

e.

Check whether the engine cranks while the Active Test "Starter" is being performed.

NOTICE:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

28.READ VALUE USING GTS (CLUTCH LOWER SW)

B

15.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
28.READ VALUE USING GTS (CLUTCH LOWER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Lower SW


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
Clutch Lower SW
50003 227 11
OK:
Tester Display Condition Normal Condition
Clutch Lower SW Clutch pedal depressed ON
Clutch pedaly released OFF



Result:
Proceed to
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG



OK (w/ Entry and Start System)

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)

OK (w/o Entry and Start System)

31.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

34.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)
29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)
a.

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G126 engine stop and start ECU connector.


c.

Disconnect the B2 clutch start switch assembly (for Lower) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-16 (STAR) - G126-17 (CLL) Always Below 1 Ω
G70-16 (STAR) - Body ground Always 10 kΩ or higher
G126-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

30.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.
A288763C19
1.51,0.323 2.031,0.604 0.521,0.281 1.313,1.698 1.333,1.375 true 0.354,0.229 0.667,0.385 0.313,0.156 10 false *a 1.208,1.729 1.667,1.927 0.458,0.198 10 false CLL 1.604,0.396 2.063,0.594 0.458,0.198 10 false G126
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the G126 engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G126-17 (CLL) - Body ground Engine started using push start switch assembly (engine start) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

31.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

32.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
a.
A285192C08
1.5,0.625 1.865,0.875 0.365,0.25 2.25,1.99 2.833,2.083 2.833,2.083 2.833,2.25 true 0.302,0.281 0.615,0.479 0.313,0.198 10 false *a 1.583,0.688 2.042,0.885 0.458,0.198 10 false G1 2.698,2.302 3.156,2.5 0.458,0.198 10 false AM2
*a Front view of wire harness connector:
(to Ignition or Starter Switch Assembly)


Disconnect the G1 ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G1-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

33.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))
a.

Disconnect the G1 ignition or starter switch assembly connector.


b.

Disconnect the B2 clutch start switch assembly (for lower) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (ST2) - B2-2 Always Below 1 Ω
G1-2 (ST2) - Body ground Always 10 kΩ or higher
B2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)
a.

Inspect the clutch start switch assembly (for lower).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG



OK (w/ Entry and Start System)

35.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

OK (w/o Entry and Start System)

36.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

35.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-16 (STAR) - ST NO. 1 relay terminal 2 Clutch pedal depressed Below 1 Ω
Clutch pedal released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the G1 ignition or starter switch assembly connector.


b.

Disconnect the G126 engine stop and start ECU connectors.


c.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (ST2) - ST NO. 1 relay terminal 2 Clutch pedal depressed Below 1 Ω
Clutch pedal released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR