Home › Drivetrain › RC60F / RC61F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › from 2016.03
RM3250E _52 Drivetrain _038036 RC60F / RC61F MANUAL TRANSMISSION / TRANSAXLE _0185585 MANUAL TRANSMISSION ASSEMBLY A

RC60F / RC61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 33504F 3.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

a.

Remove the shift lever knob sub-assembly from the shift lever.


Hide 58810J 4.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58811A 5.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)

Hide 58280A 6.REMOVE SHIFT LEVER BOOT ASSEMBLY

a.
C324629

Remove the 6 screws, 4 clips and shift lever boot assembly.


Hide 33530F 7.REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY

a.
C329822

Detach the shift lever cap boot from the manual transmission.


b.

Cover the shift lever cap with a cloth.


c.
C328999C02
1.938,0.49 2.25,0.156 2.25,0.156 2.448,0.156 true 1.865,0.802 2.031,1 0.167,0.198 10 false *a 1.75,2.354 1.948,2.531 0.198,0.177 10 false *b 1.156,3.219 1.354,3.406 0.198,0.188 10 false *c 2.51,0.052 2.677,0.25 0.167,0.198 10 false *1
*1 Shift Lever Cap
*a Press Down
*b Counterclockwise
*c Pull Out


While pressing down on the shift lever cap, turn it counterclockwise, and then pull to remove the shift lever.


Hide 33548F 8.REMOVE NO. 1 FLOOR SHIFT BUSH

a.
C329824

Remove the No. 1 floor shift bush from the floor shift shift lever assembly.


Hide 51410 10.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 11.REMOVE NO. 2 ENGINE UNDER COVER

Hide 51561D 12.REMOVE PROPELLER SHAFT GUARD

a.
C324638

Remove the propeller shaft guard with the 2 bolts.


Hide 17410 13.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1GD-FTV)

Hide 17410 14.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2GD-FTV)

Hide 17410 15.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1KD-FTV)

Hide 17410 16.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2KD-FTV)

Hide 77801A 17.REMOVE UREA TANK SUB-ASSEMBLY (w/ Urea SCR System)

Hide 12584 22.REMOVE NO. 4 CYLINDER BROCK INSULATOR

a.

Remove the No. 4 cylinder block insulator.


Hide 33119 23.REMOVE STIFFENER PLATE LH

a.
C324648

Remove the 4 bolts and stiffener plate LH.


Hide 33118 24.REMOVE STIFFENER PLATE RH

a.
C325402

Remove the 4 bolts and stiffener plate RH.


Hide 37100 25.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 41110F 26.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

Hide 27.DISCONNECT GROUND CABLE

a.
C335926

Remove the bolt and disconnect the ground cable.


Hide 28.SUPPORT MANUAL TRANSMISSION ASSEMBLY

a.
C324639

Support the manual transmission with a transmission jack.

NOTICE:
·

Make sure the high transmission jack attachment is centered on the safety stand.

·

Secure the part with a rope, attachment, etc.




Hide 51204 29.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C338961

Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.


b.
C325680

Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.


Hide 12371A 30.REMOVE REAR ENGINE MOUNTING INSULATOR

a.
C324651

Remove the 4 bolts and rear engine mounting insulator from the manual transmission assembly.


Hide 31.DISCONNECT WIRE HARNESS

a.

w/ Stop and Start System:

i.
C344347

Disconnect the neutral position switch conector.



b.
C328313

w/ Intelligent Manual Transmission Switch:

i.

Detach the 7 wire harness clamps.


ii.

Remove the bolt.


iii.

Disconnect the 3 connectors and wire harness.



c.
C328312

w/o Intelligent Manual Transmission Switch:

i.

Detach the 5 wire harness clamps.


ii.

Remove the bolt.


iii.

Disconnect the 2 connectors and wire harness.



Hide 32.REMOVE MANUAL TRANSMISSION ASSEMBLY

a.
C324649

Remove the 5 bolts and manual transmission assembly.

NOTICE:

As the manual transmission assembly is very heavy, be sure to support it securely.



Hide 33019C 33.REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C324643

Detach the 4 breather hose clamps and bracket.


b.

Remove the transmission breather sub-assembly from the control shift lever retainer assembly.


c.
C324647

Remove the 2 bolts and 2 brackets.


Hide 34.REMOVE WIRING HARNESS CLAMP BRACKET

a.
C324646

w/ Intelligent Manual Transmission Switch:

i.

Remove the 8 bolts and 7 wiring harness clamp brackets.



b.
C329814

w/o Intelligent Manual Transmission Switch:

i.

Remove the 7 bolts and 6 wiring harness clamp brackets.