Home › Engine / Hybrid System › 2GD-FTV LUBRICATION › OIL PUMP › 2016.03–2016.08
RM3250E _51 Engine / Hybrid System _038011 2GD-FTV LUBRICATION _0187780 OIL PUMP A

2GD-FTV LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the timing chain case assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)
Replacement of engine assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

(Click here)

·

w/ DPF:

(Click here)


Clear Crank Time Compensation Data Engine starting
·

(Click here)

·

w/ DPF:

(Click here)


Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

(Click here)

·

w/ DPF:

(Click here)


·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger sub-assembly

·

Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor


Perform initialization -
·

(Click here)

·

w/ DPF:

(Click here)



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.



PROCEDURE

Hide 44763C 2.REMOVE NO. 2 HOSE TO HOSE TUBE

Hide 12632 3.REMOVE NO. 2 ENGINE COVER BRACKET

Hide 82121 4.REMOVE ENGINE WIRE

Hide 26100G 6.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 7.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 89481B 8.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 9.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 25733A 10.REMOVE NO. 1 VACUUM PIPE (w/ DPF)

Hide 12631A 13.REMOVE ENGINE COVER BRACKET

Hide 89421C 15.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 25625 16.REMOVE EGR VALVE BRACKET

Hide 16206B 18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25601 20.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

Hide 25804 21.REMOVE VACUUM CONTROL VALVE SET

Hide 16209 22.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 23.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)

Hide 25800 24.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 25.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 27.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 29.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 30.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 31.REMOVE NO. 2 FUEL HOSE

Hide 23271H 32.REMOVE NO. 1 FUEL HOSE

Hide 23804D 33.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)

Hide 23815D 34.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804C 35.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 36.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 38.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 40.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 41.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23701 42.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 88431 44.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 16630D 45.REMOVE IDLER PULLEY ASSEMBLY (w/o Air Conditioning System)

Hide 12229 46.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 16282 47.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

Hide 16281 48.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

Hide 23295D 49.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 89467B 50.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)

Hide 12261 56.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 16268 58.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 16284 59.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 87101 60.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

Hide 15407 63.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 16207 65.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16304 66.REMOVE WATER OUTLET SUB-ASSEMBLY

Hide 16331A 68.REMOVE THERMOSTAT

Hide 16603 69.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A339577

Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.


Hide 16620 70.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A339579

Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


Hide 88451B 71.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16575C 74.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

Hide 12281A 75.REMOVE NO. 1 ENGINE HANGER

Hide 12501 76.REMOVE GENERATOR BRACKET SUB-ASSEMBLY

Hide 23670 77.REMOVE INJECTOR ASSEMBLY

Hide 23682 78.REMOVE NOZZLE HOLDER GASKET

Hide 11301M 79.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 80.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A339580C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat


Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.


b.
A339581C01
2.219,0.563 2.427,0.292 2.427,0.292 2.552,0.292 true 0.323,1.802 0.469,1.802 0.469,1.802 0.708,1.25 true 0.885,1.385 1.063,1.26 1.063,1.26 1.188,1.26 true 0.771,0.594 1.031,0.365 1.031,0.365 1.156,0.365 true 2.615,0.198 2.813,0.385 0.198,0.188 10 true *1 0.115,1.719 0.292,1.885 0.177,0.167 10 false *2 1.229,1.167 1.417,1.333 0.188,0.167 10 true *3 1.229,0.281 1.417,0.448 0.188,0.167 10 false *3
*1 Cylinder Head Cover Gasket
*2 No. 2 Cylinder Head Cover Gasket
*3 Camshaft Bearing Cap Oil Hole Gasket


Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.


Hide 12144 81.REMOVE OIL PAN COVER SILENCER

a.
A339601

Remove the 5 bolts and oil pan cover silencer from the oil pan sub-assembly.


Hide 89491 82.REMOVE ENGINE OIL LEVEL SENSOR

Hide 12101 83.REMOVE OIL PAN SUB-ASSEMBLY

a.
A339600C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 23 bolts and 2 nuts.


b.
A303108

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

·

Be careful not to damage the cylinder block sub-assembly flange.




Hide 16100 84.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 85.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11324 86.REMOVE TIMING CHAIN COVER PLATE

Hide 22100 87.REMOVE SUPPLY PUMP ASSEMBLY

Hide 22815A 88.REMOVE INJECTION PUMP INSULATOR

Hide 11302 89.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A339584

Remove the 20 bolts from the timing chain cover sub-assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.

A339585C01
6.156,0.719 6.49,0.177 6.49,0.177 6.625,0.177 true 5.604,1.927 6.094,2.396 6.094,2.396 6.229,2.396 true 0.406,1.156 0.552,1.156 0.552,1.156 1.052,0.708 true 0.198,1.073 0.385,1.25 0.188,0.177 10 false *a 6.302,2.313 6.51,2.479 0.208,0.167 10 false *a 6.677,0.083 6.885,0.26 0.208,0.177 10 false *a
*a Protective Tape - -


NOTICE:

Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.



c.
A339592

Remove the timing chain case gasket from the timing chain case assembly.


Hide 11303A 90.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A339586C01
0.583,1.271 1.271,1.271 true 1.417,0.917 2.167,0.354 2.167,0.354 2.375,0.354 true 2.448,0.271 2.656,0.458 0.208,0.188 10 false *a 0.354,1.188 0.563,1.375 0.208,0.188 10 false *b
*a Protective Tape
*b Wooden Block


Using a screwdriver and wooden block, pull out the front crankshaft oil seal.

NOTICE:

Do not damage the surface of the front crankshaft oil seal press fit hole.



Hide 91.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

a.
A339596

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.3 mm (0.000787 to 0.0118 in.)


Maximum gear backlash:

0.42 mm (0.0165 in.)


If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.


Hide 13519 92.REMOVE OIL PUMP DRIVE GEAR

a.
A339595

Remove the oil pump drive gear from the crankshaft.


Hide 13566B 93.REMOVE TIMING CHAIN GUIDE

Hide 13550 94.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13559 95.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

Hide 13562 96.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13507 97.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 13540 98.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 99.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

Hide 13561 100.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 101.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 13523 102.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11310 103.REMOVE TIMING CHAIN CASE ASSEMBLY

a.
A339590

Remove the 15 bolts from the timing chain case assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.

A339591C01
0.729,0.646 0.865,0.646 0.865,0.646 1.167,1.24 true 5.823,2.094 6.323,2.479 6.323,2.479 6.469,2.479 true 6.323,0.552 6.656,1.219 6.656,1.219 6.802,1.219 true 0.479,0.552 0.698,0.74 0.219,0.188 10 false *a 6.521,2.385 6.74,2.573 0.219,0.188 10 false *a 6.854,1.125 7.052,1.292 0.198,0.167 10 false *a
*a Protective Tape - -


NOTICE:

Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.



c.
A339593

Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.