Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.03
RM3250E _51 Engine / Hybrid System _038006 2GD-FTV ENGINE MECHANICAL _0192553 ENGINE ASSEMBLY A

2GD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM
·

Learning values save

·

Learning values write


Engine starting
·

w/o DPF:

(Click here)

·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)


Code registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

w/o DPF:

(Click here)

·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)


Clear Crank Time Compensation Data Engine starting
·

w/o DPF:

(Click here)

·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)


Replacement of crankshaft position sensor plate Clear Crank Time Compensation Data Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
·

w/o DPF:

(Click here)

·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)


Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

w/o DPF:

(Click here)

·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)


·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger sub-assembly

·

Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor


Perform initialization -
·

w/o DPF:

(Click here)

·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)


for AC60F:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60F:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
w/ Automatic Headlight Beam Level Control System:

The vehicle height changes due to replacement of suspension components or after performing such operations as removal and reinstallation


Headlight leveling ECU assembly initialization Headlight leveling function (Click here)
for 4WD:

Front wheel alignment adjustment


·

Clearing zero point calibration data

·

Yaw rate and acceleration sensor zero point calibration


VSC malfunctioning (Click here)

CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD and Pre-Runner)

Hide 51442 4.REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)

Hide 8.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 53301 9.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose from the hood sub-assembly.


b.

Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.


Hide 16400 10.REMOVE RADIATOR ASSEMBLY

Hide 12601B 11.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 82121 12.DISCONNECT ENGINE WIRE


b.
A358227C01
0.052,0.083 0.292,0.281 0.24,0.198 10 true *A 0.083,2.563 0.323,2.76 0.24,0.198 10 true *B
*A for LHD
*B for RHD


Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.


c.
A358228C01
0.104,0.125 0.354,0.302 0.25,0.177 10 true *A 0.083,2.542 0.333,2.719 0.25,0.177 10 true *B
*A for LHD
*B for RHD


Disconnect the connector from the engine room main wire.


d.
A358229C01
0.083,0.094 0.323,0.292 0.24,0.198 10 true *A 0.083,2.563 0.323,2.76 0.24,0.198 10 true *B
*A for LHD
*B for RHD


Detach the clamp and disconnect the 4 connectors from the glow plug controller.


e.
A358231C01
0.094,0.115 0.344,0.302 0.25,0.188 10 true *A 0.094,2.594 0.344,2.781 0.25,0.188 10 true *B
*A for LHD
*B for RHD


Detach the clamp and disconnect the engine wire from the bracket.


f.
A358232C01
0.083,0.083 0.323,0.271 0.24,0.188 10 true *A 0.094,2.583 0.333,2.771 0.24,0.188 10 true *B
*A for LHD
*B for RHD


Detach the grommet and pull out the engine wire from the cabin.


Hide 13.REMOVE AIR CLEANER CAP AND HOSE

a.
A340251

Detach the 2 clamps and disconnect the connector from the mass air flow meter.


b.
A340252

Loosen the hose clamp.


c.

Detach the 4 clips and remove the air cleaner cap and hose.


Hide 17801 14.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17341F 15.REMOVE NO. 1 AIR HOSE

a.
A340253

Slide the 2 clamps and remove the No. 1 air hose from the compressor outlet elbow and air tube.


Hide 17344E 16.REMOVE NO. 4 AIR HOSE

a.
A340255

Slide the clamp and disconnect the oil return hose from the engine oil level dipstick guide assembly.


b.
A340256

Slide the 2 clamps and remove the No. 4 air hose from the No. 2 air tube and intercooler air tube.


Hide 17363K 17.REMOVE INTERCOOLER AIR TUBE

a.
A340254

Disconnect the connector from the intake air temperature sensor.


b.
A346660

Slide the clamp and remove intercooler air tube from the diesel throttle body assembly.


Hide 23300 18.DISCONNECT FUEL FILTER ASSEMBLY

Hide 77910 19.DISCONNECT UREA TANK FILLER PIPE ASSEMBLY (w/ Urea SCR System)

Hide 77826A 20.REMOVE NO. 1 UREA TANK FILLER PIPE SUPPORT (w/ Urea SCR System)

Hide 23271H 21.REMOVE NO. 1 FUEL HOSE

a.
A340258

Detach the clamp from the No. 1 fuel hose.


b.

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


Hide 23273H 22.REMOVE NO. 2 FUEL HOSE

a.
A340257

Detach the clamp from the No. 2 fuel hose.


b.

Slide the clamp and disconnect the No. 2 fuel hose from the No. 3 nozzle leakage pipe assembly.


Hide 23.DISCONNECT WIRE HARNESS

a.
A340259

Detach the 3 clips and remove the No. 1 relay block cover upper from the engine room relay block.


b.
A340260

Detach the 2 clips and remove the No. 1 relay block cover side from the engine room relay block sub-assembly.


c.
A340261

Remove the nut and disconnect the wire to wire from the engine room relay block sub-assembly.


d.
A340262

Disconnect the 2 connectors from the engine room relay block sub-assembly.


e.
A340263

Detach the clamp and remove the 2 bolts and disconnect the No. 2 engine wire.


f.
A340264

Remove the nut and disconnect the engine room main wire from the battery positive cable.


Hide 74404B 24.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.

Loosen the 2 nuts and remove the battery clamp sub-assembly from the battery.


Hide 28800 25.REMOVE BATTERY

Hide 74431 26.REMOVE BATTERY TRAY

Hide 27.DISCONNECT WATER HOSE SUB-ASSEMBLY

a.
A346659

Slide the 2 clamps and disconnect the water hose sub-assembly from the air conditioning unit assembly.


Hide 44320 28.DISCONNECT VANE PUMP ASSEMBLY

a.
A340265

Disconnect the connector from the power steering oil pressure switch.


b.
A340266

Remove the 2 bolt and disconnect the vane pump assembly from the generator bracket.


Hide 44774 29.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A340270

Slide the clamp and disconnect the union to connector tube hose from the No. 1 hose to hose tube.


Hide 88320 31.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A340267

Remove the 2 bolts and disconnect the suction hose sub-assembly from the water inlet and timing chain cover.


b.
A340268

Disconnect the connector from the cooler compressor assembly.


c.

Remove the 2 bolt and 2 nuts.


d.
A352182

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and disconnect the cooler compressor assembly from the compressor mounting bracket.


Hide 32.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

a.
A346693

Remove the bolt and disconnect the water hose from the water inlet.


b.
A346692

Slide the 4 clamps and remove the water hose sub-assembly from the viscous heater with magnet clutch assembly, No. 2 water pipe and water outlet sub-assembly.


Hide 87120G 33.REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

a.

Disconnect the connector from the viscous heater with magnet clutch assembly.


b.
A346694

Remove the 2 bolts, nut and viscous heater with magnet clutch assembly from the No. 1 viscous heater bracket.


Hide 17410 34.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37140 35.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 37100 36.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 32101A 38.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)

Hide 35000 39.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 31210 40.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 41.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 42.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A346691

w/ Viscous Heater:

Remove the 4 bolts, viscous heater crankshaft pulley and crankshaft pulley cover from the crankshaft pulley.


b.
A343925

w/o Viscous Heater:

Remove the 4 bolts and crankshaft pulley cover from the crankshaft pulley.


c.
A349457N01
1.208,0.906 0.521,1.406 0.521,1.406 0.406,1.406 true 1.917,1.031 2.635,1.406 2.635,1.406 2.771,1.406 true 0.125,1.313 0.479,1.5 0.354,0.188 10 false SST 2.802,1.313 3.156,1.5 0.354,0.188 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


d.
A344483

for Manual Transmission:

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


e.
A344484

for Automatic Transmission:

Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate and flywheel sub-assembly from the crankshaft.


Hide 11355 43.REMOVE REAR END PLATE

a.
A340241

Remove the bolt and rear end plate from the cylinder block sub-assembly.


Hide 44.INSTALL ENGINE HANGER

a.
A343930C01
0.5,0.833 0.667,0.333 0.667,0.333 0.75,0.333 true 2.417,0.479 2.667,0.229 2.667,0.229 2.75,0.229 true 0.781,0.229 1.094,0.385 0.313,0.156 10 false *1 2.781,0.135 3.094,0.292 0.313,0.156 10 false *2
*1 No. 1 Engine Hanger Upper
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger upper and No. 2 engine hanger with the 3 bolts as shown in the illustration.

Torque:
for No. 1 engine hanger upper : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for No. 2 engine hanger : 26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:
No. 1 Engine Hanger Upper 12284-11010 or 12284-11020
No. 2 Engine Hanger 12282-11080 or 12282-11090
Bolt 90119-T0073 or 91552-81025 and 90119-T0219 or, 91672-80835



Hide 45.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.
A340269

Remove the 4 bolts and 4 nuts from the body.


c.

Remove the engine assembly by operating the engine sling device and chain block.

NOTICE:
·

Make sure that the engine assembly is clear of all wiring and hoses.

·

While lowering the engine assembly from the vehicle, do not allow it to contact the vehicle.




Hide 46.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Install the engine assembly to engine stand with the bolts.


b.

Remove the 3 bolts, No. 1 engine hanger upper and No. 2 engine hanger.


Hide 82121 47.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 12391 48.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A340271

Remove the bolt and front engine mounting insulator RH from the front engine mounting insulator.


Hide 12361 49.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A340272

Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.