Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
87211B
1.INSTALL NO. 3 AIR DUCT
Attach the claw to install the No. 3 air duct.
2.INSTALL AIR CONDITIONING UNIT ASSEMBLY
Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Temporarily install the air conditioning unit assembly and instrument panel reinforcement assembly with the nut.
| *a | Standard Position | - | - |
Align the standard position, install the drain cooler hose.
Tighten the nut.
55950G
3.INSTALL DEFROSTER NOZZLE ASSEMBLY
Attach the claw to install the defroster nozzle assembly.
55330B
4.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
for Automatic Transmission:
Install the 11 bolts.
| *A | for Manual Transmission | - | - |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
for Manual Transmission:
Install the 12 bolts.
| *A | for Driver Side |
Install 2 new hole plugs.
55306A
5.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Install the No. 1 instrument panel brace sub-assembly with the nut, bolt and 4 screws.
Attach the clamp.
55307C
6.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Install the No. 2 instrument panel brace sub-assembly with the nut, bolt and 3 screws.
7.TIGHTEN AIR CONDITIONING UNIT ASSEMBLY
Tighten the 2 screws and 3 bolts in the order shown in the illustration.
|
Bolt |
|
Screw |
82141
8.CONNECT INSTRUMENT PANEL WIRE
Install each bolt, nut and screw, and then connect the instrument panel wire.
| *A | for Automatic Air Conditioning System | *B | for Manual Air Conditioning System, Manual Cooler System |
| *C | w/ PTC Heater | *D | w/ Stop and Start System |
| *1 | Ground Wire | - | - |
Connect each connector and attach each clamp.
Install each bolt and each ground wire.
for Automatic Air Conditioning System:
Attach the clamp.
Connect the connector.
for Manual Air Conditioning System, Manual Cooler System:
Attach the clamp.
Connect the connector.
87212
9.INSTALL NO. 1 REAR AIR DUCT (w/ Rear Foot Duct)
Attach the claw to install the No. 1 rear air duct.
87212G
10.INSTALL NO. 3 REAR AIR DUCT (w/ Rear Foot Duct)
Attach the claw to install the No. 3 rear air duct.
87213
11.INSTALL NO. 2 REAR AIR DUCT (w/ Rear Foot Duct)
Attach the claw to install the No. 2 rear air duct.
87216A
12.INSTALL NO. 5 REAR AIR DUCT (w/ Rear Foot Duct)
Attach the claw to install the No. 5 rear air duct.
87216B
13.INSTALL NO. 4 REAR AIR DUCT (w/ Rear Foot Duct)
Attach the claw to install the No. 4 rear air duct.
58861B
14.INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Resistor Duct)
for Automatic Transmission:
Install the No. 1 console box duct with the 2 clips.
| *A | w/ Entry and Start System |
w/ Entry and Start System:
Attach the clamp to install the No. 2 console box mounting bracket.
Install the 2 bolts.
for Manual Transmission:
Install the No. 1 console box duct with the 3 clips.
| *A | w/ Entry and Start System |
w/ Entry and Start System:
Attach the clamp to install the No. 2 console box mounting bracket.
Install the 2 bolts.
55215D
15.INSTALL NO. 3 DASH PANEL INSULATOR PAD
Install the No. 3 dash panel insulator pad.
55214C
16.INSTALL NO. 2 DASH PANEL INSULATOR PAD
Install the No. 2 dash panel insulator pad.
55395C
17.INSTALL NO. 1 INSTRUMENT PANEL INNER BRACKET COVER LH (for LHD)
Install the No. 1 instrument panel inner bracket cover LH with the 3 clips.
18.INSTALL FRONT FLOOR CARPET ASSEMBLY
Attach the guide to install the front floor carpet assembly to the original position as shown in the illustration.
| *A | for LHD | - | - |
|
Fastener |
|
Install in this Direction |
Attach each fastener.
for LHD:
Install the 5 clips.
for RHD:
Install the 4 clips.
62414A
19.INSTALL LOWER CENTER PILLAR GARNISH LH (for Double Cab)
62413A
20.INSTALL LOWER CENTER PILLAR GARNISH RH (for Double Cab)
67918E
21.INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab)
67917C
22.INSTALL REAR DOOR SCUFF PLATE RH (for Double Cab)
62112
23.INSTALL COWL SIDE TRIM BOARD LH
67914B
24.INSTALL FRONT DOOR SCUFF PLATE LH
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>INSTALLATION
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Single Cab)>INSTALLATION
for Smart Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Smart Cab)>INSTALLATION
62111C
25.INSTALL COWL SIDE TRIM BOARD RH
67913B
26.INSTALL FRONT DOOR SCUFF PLATE RH
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>INSTALLATION
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Single Cab)>INSTALLATION
for Smart Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Smart Cab)>INSTALLATION
27.INSTALL STEERING COLUMN ASSEMBLY
87211
28.INSTALL NO. 1 AIR DUCT
Attach the claw to install the No. 1 air duct.
If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.
Install the bolt.
87211A
29.INSTALL NO. 2 AIR DUCT
Attach the claw to install the No. 2 air duct.
If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.
86740
30.INSTALL TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics Transceiver)
55303B
31.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
58810J
32.INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid)
58811A
33.INSTALL FRONT CONSOLE BOX (w/o Console Box Lid)
34.INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSTALLATION
for Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>INSTALLATION
35.INSTALL FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
87128
36.INSTALL HEATER GROMMET (w/ Heater)
Press the marked parts to attach the claw and install the heater grommet.
Securely install the heater grommet in order to prevent water ingress.
Install the heater grommet so that there is no clearance between the grommet and heater pipe.
37.CONNECT HEATER WATER INLET HOSE (w/ Heater)
| *a | View A |
| *b | for 1GR-FE: Marking (Yellow)
for 1GD-FTV, 2GD-FTV: Marking (Yellow) for 1KD-FTV, 2KD-FTV: Marking (Yellow) for 1TR-FE, 2TR-FE: Marking (Yellow) for 5L-E: Marking (Yellow) |
| *c | Clip Installation Angle (45°) |
Connect the heater water inlet hose with the marking facing left and attach the clip within the area shown in the illustration.
Do not apply excessive force to the heater water inlet hose.
38.CONNECT HEATER WATER OUTLET HOSE (w/ Heater)
| *a | View A |
| *b | for 1GR-FE: Marking (White)
for 1GD-FTV, 2GD-FTV: Marking (White) for 1KD-FTV, 2KD-FTV: Marking (White) for 1TR-FE, 2TR-FE: Marking (White) for 5L-E: Marking (White) |
| *c | Clip Installation Angle (40°) |
Connect the heater water outlet hose with the marking facing left and attach the clip within the area shown in the illustration.
Do not apply excessive force to the heater water outlet hose.
17129
39.INSTALL INTAKE AIR SURGE TANK (for 1GR-FE)
88710E
40.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV, 2GD-FTV)
Remove the vinyl tape from the air conditioner tube and accessory assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.
ND-OIL 8 or equivalent
Install the O-ring to the air conditioner tube and accessory assembly.
Keep the O-ring and O-ring fitting surfaces free of foreign matter.
Connect the air conditioner tube and accessory assembly.
88707
41.CONNECT SUCTION PIPE SUB-ASSEMBLY (except 1GD-FTV, 2GD-FTV)
Remove the vinyl tape from the suction pipe sub-assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.
ND-OIL 8 or equivalent
Install the O-ring to the suction pipe sub-assembly.
Keep the O-ring and O-ring fitting surfaces free of foreign matter.
Connect the suction pipe sub-assembly.
|
Install in this Direction |
Rotate the hook connector as shown in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
88710E
42.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (for 1GD-FTV, 2GD-FTV)
Remove the vinyl tape from the air conditioner tube and accessory assembly.
Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the air conditioner tube and accessory assembly.
ND-OIL 8 or equivalent
Install the 2 O-rings to the air conditioner tube and accessory assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
Connect the air conditioner tube and accessory assembly.
Tighten the bolt.
43.ADD ENGINE COOLANT (w/ Heater)
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE COOLING>COOLANT>REPLACEMENT
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV COOLING>COOLANT>REPLACEMENT
for 2GD-FTV:
Click hereEngine / Hybrid System>2GD-FTV COOLING>COOLANT>REPLACEMENT
for 1KD-FTV:
Click hereEngine / Hybrid System>1KD-FTV COOLING>COOLANT>REPLACEMENT
for 2KD-FTV:
Click hereEngine / Hybrid System>2KD-FTV COOLING>COOLANT>REPLACEMENT
for 1TR-FE:
Click hereEngine / Hybrid System>1TR-FE COOLING>COOLANT>REPLACEMENT
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE COOLING>COOLANT>REPLACEMENT
for 5L-E:
Click hereEngine / Hybrid System>5L-E COOLING>COOLANT>REPLACEMENT
44.INSPECT FOR COOLANT LEAK (w/ Heater)
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
for 2GD-FTV:
Click hereEngine / Hybrid System>2GD-FTV COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
for 1KD-FTV:
Click hereEngine / Hybrid System>1KD-FTV COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
for 2KD-FTV:
Click hereEngine / Hybrid System>2KD-FTV COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
for 1TR-FE:
Click hereEngine / Hybrid System>1TR-FE COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
for 5L-E:
Click hereEngine / Hybrid System>5L-E COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
45. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
46. WARM UP ENGINE
47.INSPECT FOR REFRIGERANT LEAK
48. INITIALIZATION SERVO MOTOR (for Automatic Air Conditioning System)