Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › CAMSHAFT(w/o EGR Cooler) › from 2016.08
RM3250E _51 Engine / Hybrid System _038006 2GD-FTV ENGINE MECHANICAL _0290068 CAMSHAFT(w/o EGR Cooler) A

2GD-FTV ENGINE MECHANICAL  CAMSHAFT(w/o EGR Cooler)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger sub-assembly

·

Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor


Perform initialization - (Click here)

CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD)

Hide 12601B 6.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 16593 7.REMOVE NO. 1 RADIATOR AIR GUIDE

Hide 17344E 8.REMOVE NO. 4 AIR HOSE

Hide 17362B 9.REMOVE NO. 2 AIR TUBE

Hide 16571C 10.REMOVE NO. 1 RADIATOR HOSE

Hide 44360 11.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 44369A 12.REMOVE NO. 1 OIL RESERVOIR BRACKET

Hide 16470 13.REMOVE RADIATOR RESERVE TANK ASSEMBLY

Hide 32942 14.DISCONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 32941 15.DISCONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 16711 16.REMOVE FAN SHROUD

Hide 16572D 17.DISCONNECT NO. 2 RADIATOR HOSE

Hide 16400 18.REMOVE RADIATOR ASSEMBLY

Hide 17363K 19.REMOVE INTERCOOLER AIR TUBE

Hide 26100G 20.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 12632 25.REMOVE NO. 2 ENGINE COVER BRACKET

Hide 25800 30.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 32.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 33.REMOVE HARNESS BRACKET

Hide 23760 34.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 35.REMOVE NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 36.REMOVE INJECTOR ASSEMBLY

Hide 23682 37.REMOVE NOZZLE HOLDER GASKET

Hide 11301M 38.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 39.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 40.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A345765C01
1.469,1.344 1.052,1.01 1.052,1.01 0.885,1.01 true 1.604,1.375 2.021,1.875 2.021,1.875 2.188,1.875 true 2.208,3.229 2.49,2.833 2.49,2.833 2.656,2.833 true 0.979,3.229 0.729,2.833 0.729,2.833 0.563,2.833 true 1.01,3.323 1,3.75 false 2.219,3.323 2.208,3.75 false 0.677,0.906 0.865,1.063 0.188,0.156 10 true *a 2.656,2.729 2.885,2.896 0.229,0.167 10 false *b 2.198,1.771 2.385,1.927 0.188,0.156 10 true *a 0.354,2.74 0.552,2.906 0.198,0.167 10 false *b 0.938,3.76 1.135,3.927 0.198,0.167 10 true *a 2.146,3.76 2.344,3.927 0.198,0.167 10 true *a
*a Timing Mark
*b Paint Mark


Align the timing mark of the crankshaft pulley and timing chain cover by rotating the crankshaft clockwise.


b.

Make sure that the timing mark of the camshaft timing sprocket is at the top.

HINT:

If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).



c.

Place paint marks on the No. 2 chain sub-assembly.


Hide 41.REMOVE NO. 3 CAMSHAFT BEARING CAP

a.
A345780

Remove the 2 bolts and No. 3 camshaft bearing cap from the cylinder head sub-assembly.


Hide 29300 42.REMOVE VACUUM PUMP ASSEMBLY

Hide 11382C 43.REMOVE CAMSHAFT OIL SEAL RETAINER

Hide 13566B 44.REMOVE TIMING CHAIN GUIDE

a.
A345766

Remove the bolt and timing chain guide from the cylinder head sub-assembly.


Hide 45.REMOVE CAMSHAFT

a.
A345767

Remove the oil pump relief valve plug and gasket from timing chain cover.


b.
A345768C01
1.792,0.885 2.333,1.083 2.333,1.083 2.5,1.083 true 1.708,1.75 2.333,1.75 true 2.521,0.969 2.719,1.135 0.198,0.167 10 true *a 2.344,1.646 2.563,1.802 0.219,0.156 10 true *b
*a Stopper Plate
*b Pin


Insert a pin into stopper plate hole of the No. 2 chain tensioner assembly and lock the No. 2 chain tensioner assembly.


c.
A345769C01
1.938,0.625 2.875,0.625 true 0.604,2.938 1.438,2.938 true 2.896,0.521 3.104,0.677 0.208,0.156 10 false *1 0.448,2.833 0.635,2.99 0.188,0.156 10 false *2
*1 No. 1 Camshaft
*2 No. 2 Camshaft


Hold the hexagonal portion of the camshaft with a wrench and loosen the 2 bolts from the No. 1 camshaft and No. 2 camshaft.

NOTICE:

Be careful not to damage the cylinder head sub-assembly with the wrench.



d.
A345770N01
0.583,0.875 0.771,1.042 0.188,0.167 10 true 12 0.021,0.656 0.146,0.823 0.125,0.167 10 true 3 0.031,1.323 0.156,1.49 0.125,0.167 10 true 4 0.073,1.76 0.198,1.927 0.125,0.167 10 true 2 0.052,0.219 0.177,0.385 0.125,0.167 10 true 1 0.479,1.677 0.667,1.844 0.188,0.167 10 true 11 1.198,1.708 1.385,1.875 0.188,0.167 10 true 19 1.917,1.698 2.104,1.865 0.188,0.167 10 true 15 2.625,1.708 2.771,1.875 0.146,0.167 10 true 7 1.292,0.875 1.479,1.042 0.188,0.167 10 true 20 1.979,0.875 2.167,1.042 0.188,0.167 10 true 16 2.667,0.875 2.792,1.042 0.125,0.167 10 true 8 1.052,1.104 1.24,1.271 0.188,0.167 10 true 10 1.74,1.104 1.927,1.271 0.188,0.167 10 true 18 2.417,1.115 2.604,1.281 0.188,0.167 10 true 14 3.208,0.354 3.396,0.521 0.188,0.167 10 true 5 3.125,1.115 3.25,1.281 0.125,0.167 10 true 6 1.198,0.375 1.385,0.542 0.188,0.167 10 true 9 1.854,0.365 2.042,0.531 0.188,0.167 10 true 17 2.542,0.354 2.729,0.521 0.188,0.167 10 true 13

Using several steps, and remove the 20 bolt, No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps from the cylinder head sub-assembly.


e.
A345771

Raise the No. 1 camshaft and remove the bolt from the No. 1 camshaft.


f.

Raise the No. 2 camshaft and remove the bolt from the No. 2 camshaft.


g.
A345772

Remove the No. 2 camshaft from the camshaft timing sprocket.


h.
A345774

Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.


i.
A345773

Remove the No. 1 camshaft from the camshaft timing sprocket.


j.
A345775

Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.


k.
A345776

Suspend the No. 2 chain sub-assembly with a string or equivalent.

HINT:

Be careful not to drop the No. 2 chain sub-assembly inside the timing chain cover assembly.