There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Back Door Closer System *2: w/ Smart Entry and Start System *3: w/ Navigation System *4: w/ Audio and Visual System *5: for LED Headlight *6: for 4WD *7: w/ VSC |
|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω. | ·
Short between CAN bus lines ·
ECM ·
Brake actuator assembly (skid control ECU) ·
Spiral with sensor cable sub-assembly (steering angle sensor)*7 ·
Air conditioning amplifier assembly ·
Multiplex network door ECU*1 ·
Airbag sensor assembly ·
Certification ECU (smart key ECU assembly)*2 ·
Navigation receiver assembly*3 ·
Radio and display receiver assembly*4 ·
Headlight leveling ECU assembly*5 ·
4 wheel drive control ECU*6 ·
Combination meter assembly ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector ·
DLC3 CAN branch wire or connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
When replacing the combination meter assembly, make sure to replace it with a new one.
Before replacing the certification ECU (smart key ECU assembly), refer to the service bulletin.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G7-6 (CANH) - G7-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G7-6 (CANH) - G7-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 CAN junction connectors.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: for 4WD *2: w/ Navigation System *3: w/ Audio and Visual System |
|||
| G120 | Y | W | Airbag Sensor Assembly |
| G121 | GR | W | Air Conditioning Amplifier Assembly |
| G122 | B | W | ECM |
| G125 | R | W | 4 Wheel Drive Control ECU*1 |
| G126 | V | W | ·
Navigation Receiver Assembly*2 ·
Radio and Display Receiver Assembly*3 |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for 4WD *2: w/ Navigation System *3: w/ Audio and Visual System |
||
| G120-1 (CANH) - G120-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G121-1 (CANH) - G121-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G122-1 (CANH) - G122-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G125-1 (CANH) - G125-2 (CANL)*1 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G126-1 (CANH) - G126-2 (CANL)*2, *3 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to airbag sensor assembly CAN branch wire) | B |
| NG (to air conditioning amplifier assembly CAN branch wire) (for Automatic Air Conditioning System) | C |
| NG (to air conditioning amplifier assembly CAN branch wire) (for Manual Air Conditioning System) | D |
| NG (to ECM CAN main wire) | E |
| NG (to 4 wheel drive control ECU CAN branch wire) (for 4WD) | F |
| NG (to navigation receiver assembly CAN branch wire) (w/ Navigation System) | G |
| NG (to radio and display receiver assembly CAN branch wire) (w/ Audio and Visual System) | H |
A
B
C
D
E
F
G
H
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Disconnect the airbag sensor assembly connector.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G46-13 (CANH) - G46-22 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-11 (TX+) - G37-12 (TX-) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G131-8 (TX+) - G131-9 (TX-) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
for 2TR-FE:
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G142-13 (CANH) - G142-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
for 1GR-FE:
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Connector | Specified Condition |
|---|---|---|
| G145-31 (CANH) - G145-25 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
for 1KD-FTV, 2KD-FTV:
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G140-24 (CANH) - G140-23 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
for 1GD-FTV, 2GD-FTV:
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G49-17 (CANH) - G49-28 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
for 5L-E:
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G161-25 (CANH) - G161-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL
for 1KD-FTV:
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2KD-FTV:
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2GD-FTV:
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 5L-E:
Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ECM>REMOVAL
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to 4 Wheel Drive Control ECU) |
Disconnect the 4 wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C60-20 (CANH) - C60-40 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
Disconnect the navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G41-9 (CANH) - G41-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G100-9 (CANH) - G100-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connector.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: for LED Headlight *2: w/ Smart Entry and Start System *3: w/ Back Door Closer System *4: w/ VSC |
|||
| G93 | B | W | Brake Actuator Assembly (Skid Control ECU) |
| G94 | BE | W | Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*4 |
| G96 | P | W | Combination Meter Assembly |
| G98 | V | W | Headlight Leveling ECU Assembly*1 |
| G99 | G | W | Certification ECU (Smart Key ECU Assembly)*2 |
| G168 | LG | W | No. 2 CAN Junction Connector |
| G169 | SB | W | Multiplex Network Door ECU*3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for LED Headlight *2: w/ Smart Entry and Start System *3: w/ Back Door Closer System *4: w/ VSC |
||
| G93-1 (CANH) - G93-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G94-1 (CANH) - G94-2 (CANL)*4 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G96-1 (CANH) - G96-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G98-1 (CANH) - G98-2 (CANL)*1 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G99-1 (CANH) - G99-2 (CANL)*2 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G168-1 (CANH) - G168-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G169-1 (CANH) - G169-2 (CANL)*3 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to brake actuator assembly [skid control ECU] CAN branch wire) | B |
| NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) (w/ VSC) | C |
| NG (to combination meter assembly CAN main wire) | D |
| NG (to headlight leveling ECU assembly CAN branch wire) (for LED Headlight) | E |
| NG (to certification ECU [smart key ECU assembly] CAN branch wire) (w/ Smart Entry and Start System) | F |
| NG (to multiplex network door ECU CAN branch wire) (w/ Back Door Closer System) | G |
| NG (to No. 2 CAN junction connector CAN main wire) | H |
A
B
C
D
E
F
G
H
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *A | w/ VSC |
| *B | w/o VSC |
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-22 (CANH) - A4-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A68-25 (CANH) - A68-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
w/ VSC:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL
w/o VSC:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor]) |
Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G22-3 (CANH) - G22-2 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-36 (CANH) - G8-35 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Headlight Leveling ECU Assembly) |
Disconnect the headlight leveling ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-6 (CANH) - G40-7 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-40 (CANH) - G17-18 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *A | w/ Power Back Door System |
| *B | w/o Power Back Door System |
| *a | Rear view of wire harness connector
(to Multiplex Network Door ECU) |
Disconnect the multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V12-13 (CANP) - V12-14 (CANN) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V25-13 (CANP) - V25-14 (CANN) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG