Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL RELAY › from 2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0249875 DOOR CONTROL RELAY G

DOOR LOCK  DOOR CONTROL RELAY  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the door lock relay removal/installation are shown below.

Necessary Procedures After Parts Removed / Installed / Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal
w/ Power Back Door System:

Reset back door close position


Power back door system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55667 3.REMOVE INSTRUMENT PANEL REGISTER BEZEL GARNISH

Hide 55011A 4.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55012A 5.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55405B 6.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 55522B 7.REMOVE RADIO TUNER OPENING COVER (w/o Audio)

Hide 86120 8.REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio, for Radio Receiver Type)

Hide 86140A 9.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio, for Radio and Display Type)

Hide 86120L 10.REMOVE NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

Hide 55905J 11.REMOVE CONTROL KNOB SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 84013A 12.REMOVE INTEGRATION PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55900 13.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 55407C 14.REMOVE LOWER INSTRUMENT COVER SUB-ASSEMBLY

Hide 84930G 15.REMOVE DOOR LOCK CONTROL RELAY (for RHD)

a.
B438953C01
1.854,0.635 2.052,0.427 2.052,0.427 2.344,0.427 true 1.76,1.458 1.948,1.802 1.948,1.802 2.125,1.802 true 2.021,0.969 2.458,0.969 true 2.271,0.344 2.583,0.542 0.313,0.198 10 true *1 2.417,0.875 2.729,1.073 0.313,0.198 10 true *2 2.115,1.719 2.427,1.917 0.313,0.198 10 true *3
*1 No. 1 Door Lock Control Relay
*2 No. 2 Door Lock Control Relay
*3 No. 3 Door Lock Control Relay


Remove the door lock control relay.


Hide 84930G 16.REMOVE DOOR LOCK CONTROL RELAY (for LHD)

a.
B438905C05
1.625,0.698 1.354,0.323 1.354,0.323 1.073,0.323 true 1.646,1.083 1.302,1.521 1.302,1.521 1.021,1.521 true 0.854,0.24 1.167,0.438 0.313,0.198 10 true *1 0.854,1.438 1.167,1.635 0.313,0.198 10 true *2
*1 No. 1 Door Lock Control Relay
*2 No. 2 Door Lock Control Relay


Remove the door lock control relay.


Hide 84930G 17.INSPECT NO. 1 DOOR LOCK CONTROL RELAY

a.
B441598N06
2.875,1.24 2.979,1.24 false 2.875,1.583 2.979,1.583 false 2.188,1.063 2.26,0.969 false 2.563,1.063 2.635,0.969 false 2.969,1.073 3.042,0.979 false 1.573,0.896 1.729,1.094 0.156,0.198 10 false 5 1.573,1.396 1.729,1.594 0.156,0.198 10 false 2 1.573,0.396 1.729,0.594 0.156,0.198 10 false 4 0.281,0.688 0.438,0.885 0.156,0.198 10 false 3 0.292,1.396 0.448,1.594 0.156,0.198 10 false 1 3.031,1.177 3.188,1.375 0.156,0.198 10 false 5 3.031,1.521 3.188,1.719 0.156,0.198 10 false 3 2.104,1.031 2.26,1.229 0.156,0.198 10 false 1 2.458,1.021 2.615,1.219 0.156,0.198 10 false 4 2.854,1.01 3.01,1.208 0.156,0.198 10 false 2

Inspect the No. 1 door lock control relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 1 door lock control relay.



Hide 84930H 18.INSPECT NO. 2 DOOR LOCK CONTROL RELAY

a.
B441598N07
2.875,1.24 2.979,1.24 false 2.875,1.583 2.979,1.583 false 2.188,1.063 2.26,0.969 false 2.563,1.063 2.635,0.969 false 2.969,1.073 3.042,0.979 false 1.573,0.896 1.729,1.094 0.156,0.198 10 false 5 1.573,1.396 1.729,1.594 0.156,0.198 10 false 2 1.573,0.396 1.729,0.594 0.156,0.198 10 false 4 0.281,0.688 0.438,0.885 0.156,0.198 10 false 3 0.292,1.396 0.448,1.594 0.156,0.198 10 false 1 3.031,1.177 3.188,1.375 0.156,0.198 10 false 5 3.031,1.521 3.188,1.719 0.156,0.198 10 false 3 2.104,1.031 2.26,1.229 0.156,0.198 10 false 1 2.458,1.021 2.615,1.219 0.156,0.198 10 false 4 2.854,1.01 3.01,1.208 0.156,0.198 10 false 2

Inspect the No. 2 door lock control relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 2 door lock control relay.



Hide 84930H 19.INSPECT NO. 3 DOOR LOCK CONTROL RELAY (w/ Double Locking System)

a.
B441598N03
2.875,1.24 2.979,1.24 false 2.875,1.583 2.979,1.583 false 2.188,1.063 2.26,0.969 false 2.563,1.063 2.635,0.969 false 2.969,1.073 3.042,0.979 false 1.573,0.896 1.729,1.094 0.156,0.198 10 false 5 1.573,1.396 1.729,1.594 0.156,0.198 10 false 2 1.573,0.396 1.729,0.594 0.156,0.198 10 false 4 0.281,0.688 0.438,0.885 0.156,0.198 10 false 3 0.292,1.396 0.448,1.594 0.156,0.198 10 false 1 3.031,1.177 3.188,1.375 0.156,0.198 10 false 5 3.031,1.521 3.188,1.719 0.156,0.198 10 false 3 2.104,1.031 2.26,1.229 0.156,0.198 10 false 1 2.458,1.021 2.615,1.219 0.156,0.198 10 false 4 2.854,1.01 3.01,1.208 0.156,0.198 10 false 2

Inspect the No. 3 door lock control relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 3 door lock control relay.



Hide 84930G 20.INSTALL DOOR LOCK CONTROL RELAY (for RHD)

a.
B438953C01
1.854,0.635 2.052,0.427 2.052,0.427 2.344,0.427 true 1.76,1.458 1.948,1.802 1.948,1.802 2.125,1.802 true 2.021,0.969 2.458,0.969 true 2.271,0.344 2.583,0.542 0.313,0.198 10 true *1 2.417,0.875 2.729,1.073 0.313,0.198 10 true *2 2.115,1.719 2.427,1.917 0.313,0.198 10 true *3
*1 No. 1 Door Lock Control Relay
*2 No. 2 Door Lock Control Relay
*3 No. 3 Door Lock Control Relay


Remove the door lock control relay.


Hide 84930G 21.INSTALL DOOR LOCK CONTROL RELAY (for LHD)

a.
B438905C06
1.625,0.698 1.354,0.323 1.354,0.323 1.073,0.323 true 1.646,1.083 1.302,1.521 1.302,1.521 1.021,1.521 true 0.854,0.24 1.167,0.438 0.313,0.198 10 true *1 0.854,1.438 1.167,1.635 0.313,0.198 10 true *2
*1 No. 1 Door Lock Control Relay
*2 No. 2 Door Lock Control Relay


Install the door lock control relay.


Hide 55407C 22.INSTALL LOWER INSTRUMENT COVER SUB-ASSEMBLY

Hide 55900 23.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 84013A 24.INSTALL INTEGRATION PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55905J 25.INSTALL CONTROL KNOB SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55522B 26.INSTALL RADIO TUNER OPENING COVER (w/o Audio)

Hide 86120 27.INSTALL RADIO RECEIVER ASSEMBLY (w/ Audio, for Radio Receiver Type)

Hide 86140A 28.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio, for Radio and Display Type)

Hide 86120L 29.INSTALL NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

Hide 55405B 30.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 55011A 31.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55012A 32.INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55667 33.INSTALL INSTRUMENT PANEL REGISTER BEZEL GARNISH

Hide 34.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION