The air conditioning amplifier assembly outputs the magnet clutch ON request signal to the ECM. The ECM sends a magnet clutch ON permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on this signal.
Inspect the fuses for circuits related to this system before performing the following procedure.
When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.
Use the Data List to check if the magnet clutch ON request signal is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/C Signal | Magnet clutch ON request signal | ON or OFF | ON: "A/C" switch on
OFF: "A/C" switch off |
Operates with the engine idling and the blower switch on (LO level). |
| Tester Display |
|---|
| A/C Signal |
Display is as specified in normal condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the A/C COMP relay from the No. 4 instrument panel relay block assembly.
Inspect the A/C COMP relay.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air conditioning amplifier assembly connector.
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G37-20 (MGC) - Body ground | Ignition switch off | Below 1 V |
| G37-20 (MGC) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-20 (MGC) - Body ground | ·
Engine idling ·
Blower switch: On (LO level) ·
"A/C" switch: On (magnet clutch on) |
Below 1 V |
| G37-20 (MGC) - Body ground | ·
Engine idling ·
Blower switch: On (LO level) ·
"A/C" switch: Off or on (magnet clutch off) |
11 to 14 V |
| Result | Proceed to |
|---|---|
| OK (w/ Magnet Clutch Assembly) | A |
| OK (w/o Magnet Clutch Assembly) | B |
| NG | C |
A
B
C
Remove the compressor assembly with magnet clutch.
Inspect the compressor assembly with magnet clutch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the magnet A/C COMP relay assembly from the No. 4 instrument panel junction block assembly.
Disconnect the C3 compressor assembly with magnet clutch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 3 - C3-1 (MG+) | Always | Below 1 Ω |
| Relay terminal 3 or C3-1 (MG+) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Relay terminal 5 - Body ground | Engine switch off | Below 1 V |
| Relay terminal 5 - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G37 air conditioning amplifier assembly connector.
except 5L-E:
Disconnect the G145*1, G143*2, G50*3 or G140*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV
for 5L-E:
Disconnect the G160 and G161 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-17 (AC1) - G145-33 (AC1) | Always | Below 1 Ω |
| G37-24 (ACT) - G145-27 (ACT) | Always | Below 1 Ω |
| G37-17 (AC1) or G145-33 (AC1) - Body ground | Always | 10 kΩ or higher |
| G37-24 (ACT) or G145-27 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-17 (AC1) - G143-30 (AC1) | Always | Below 1 Ω |
| G37-24 (ACT) - G143-24 (ACT) | Always | Below 1 Ω |
| G37-17 (AC1) or G143-30 (AC1) - Body ground | Always | 10 kΩ or higher |
| G37-24 (ACT) or G143-24 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-17 (AC1) - G50-15 (AC1) | Always | Below 1 Ω |
| G37-24 (ACT) - G50-14 (ACT) | Always | Below 1 Ω |
| G37-17 (AC1) or G50-15 (AC1) - Body ground | Always | 10 kΩ or higher |
| G37-24 (ACT) or G50-14 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-17 (AC1) - G140-18 (AC1) | Always | Below 1 Ω |
| G37-24 (ACT) - G140-19 (ACT) | Always | Below 1 Ω |
| G37-17 (AC1) or G140-18 (AC1) - Body ground | Always | 10 kΩ or higher |
| G37-24 (ACT) or G140-19 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-17 (AC1) - G160-34 (AC1) | Always | Below 1 Ω |
| G37-24 (ACT) - G161-9 (ACT) | Always | Below 1 Ω |
| G37-17 (AC1) or G160-34 (AC1) - Body ground | Always | 10 kΩ or higher |
| G37-24 (ACT) or G161-9 (ACT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-17 (AC1) - Body ground | ·
Engine idling ·
Blower switch: On (LO level) ·
"A/C" switch: On |
Below 1 V |
| G37-17 (AC1) - Body ground | ·
Engine idling ·
Blower switch: On (LO level) ·
"A/C" switch: Off |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G37 air conditioning amplifier assembly connector.
Disconnect the G145*1, G143*2, G50*3, G140*4 or G161*5 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV
*5: for 5L-E
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-24 (ACT) - G145-27 (ACT) | Always | Below 1 Ω |
| G37-24 (ACT) or G145-27 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-24 (ACT) - G143-24 (ACT) | Always | Below 1 Ω |
| G37-24 (ACT) or G143-24 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-24 (ACT) - G50-14 (ACT) | Always | Below 1 Ω |
| G37-24 (ACT) or G50-14 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-24 (ACT) - G140-19 (ACT) | Always | Below 1 Ω |
| G37-24 (ACT) or G140-19 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-24 (ACT) - G161-9 (ACT) | Always | Below 1 Ω |
| G37-24 (ACT) or G161-9 (ACT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-24 (ACT) - Body ground | ·
Engine idling ·
Blower switch: On (LO level) ·
"A/C" switch: Off or on (magnet clutch off) |
Below 1 V |
| G37-24 (ACT) - Body ground | ·
Engine idling ·
Blower switch: On (LO level) ·
"A/C" switch: On (magnet clutch on) |
4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG