Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  Brake Override System  


DESCRIPTION

When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

A232420E58
2.104,2.531 3.031,3.104 0.927,0.573 10 false Vehicle Speed 0.448,2.854 1.802,3.135 1.354,0.281 10 false Wheel Speed Sensor 0.417,2.396 1.823,2.646 1.406,0.25 10 false Vehicle Speed Sensor 0.448,1.677 1.615,2 1.167,0.323 10 false Stop Light Switch 0.458,0.708 1.625,1.333 1.167,0.625 10 false Accelerator Pedal Position Sensor 1.021,2.625 1.167,2.854 0.146,0.229 10 false or 3.635,0.719 3.979,0.969 0.344,0.25 10 false ECM 4.979,1.25 7.031,1.917 2.052,0.667 10 false Effective Accelerator Pedal Angle for System Control 2.094,1.781 2.667,2.083 0.573,0.302 10 false ON/OFF 1.885,0.844 3.063,1.417 1.177,0.573 10 false Actual Accelerator Pedal Angle 0.094,0 1.646,0.281 1.552,0.281 10 false Brake Override System:

Activation Conditions:
·

Vehicle is running at or above a specified speed.

·

The accelerator pedal is depressed beyond a specified level, and then the brake pedal is depressed.


NOTICE:

The vehicle may not enter brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.



Items Controlled:
·

Driving torque is restricted.


HINT:

During brake override system control, the value for the accelerator pedal angle (which is used for engine control) is forcibly reduced to a specified value. For this reason, the Data List value for Throttle Sensor Position will be replaced with a specified value regardless of the actual accelerator pedal angle (Accel Sens. No. 1 Volt %, Accel Sens. No. 2 Volt %).



Deactivation Conditions:
·

When the stop light switch turns off or the actual accelerator pedal angle increases or decreases beyond the specified range.



CAUTION / NOTICE / HINT

Inspection Method

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, the brake override system has been activated.


CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving, make absolutely sure that all traffic laws, such as speed limits, are observed.


HINT:
·

Under normal conditions, the Throttle Sensor Position value changes in response to the Accel Sens. No. 1 Volt % value. For more information on the numerical values, refer to the Data List (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

If the Data List values of Throttle Sensor Position and Accel Sens. No. 1 Volt % do not match, and the value of Throttle Sensor Position changes but the value of Accel Sens. No. 1 Volt % is constant, this confirms that the brake override system has activated. (Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the driving test.)



NOTICE:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Utility / All Codes.


d.

Check DTCs.

Result:
Result Proceed to
No DTC output A
DTC output B




A

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH AND ST1)

B

GO TO DTC CHART

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH AND ST1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

Powertrain > Engine > Data List
Tester Display
ST1
Stop Light Switch
50003 61 137,188

d.

Check the Data List indication when the brake pedal is depressed and released.

OK:
Intelligent Tester Display Condition Specified Condition
Stop Light Switch Brake pedal released OFF
Brake pedal depressed ON
ST1 Brake pedal released OFF
Brake pedal depressed ON



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE PEDAL

NG

INSPECT STOP LIGHT SWITCH ASSEMBLY

3.INSPECT BRAKE PEDAL
a.

Inspect and adjust the brake pedal.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

HINT:

If the stop light switch turns on too late, the start of brake override system control may be delayed; if it turns on too soon, brake override system control may begin too early. Therefore, it is necessary to conduct inspection of the brake pedal and stop light switch assembly.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE BRAKE PEDAL

4.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %.

Powertrain > Engine > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.

Read the value displayed on the intelligent tester.

OK:
Intelligent Tester Display Condition Specified Condition
Accel Sens. No. 1 Volt % Accelerator Pedal Released → Depressed → Released Values smoothly change following accelerator pedal operation
Accel Sens. No. 2 Volt %


HINT:

For numerical values of Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %, refer to the Data List.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

NG

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

5.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 61 316

e.

Read the value displayed on the intelligent tester.

Standard:
Intelligent Tester Display Condition Specified Condition
Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle driven at constant speed between 16.1 and 64.4 km/h (10 and 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the driving test.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER (FR, FL, RR, RL WHEEL SPEED)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

6.READ VALUE USING INTELLIGENT TESTER (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Start the engine.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 8 127,130,131,134

e.

Read the value displayed on the intelligent tester.

Standard:
Intelligent Tester Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle driven at constant speed between 16.1 and 64.4 km/h (10 and 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the driving test.



Result:
Proceed to
OK
NG



OK

END

NG

INSPECT FRONT OR REAR SPEED SENSOR