Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1880E _58 Vehicle Interior _013240 METER / GAUGE / DISPLAY _0068630 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the speedometer sensor.

NOTICE:

If the speedometer operation is not normal, refer to "Speedometer Malfunction" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).


WIRING DIAGRAM

E234268
0.695,1.403 2.063,1.567 1.368,0.164 10 Speedometer Sensor 5.086,1.935 5.196,2.091 0.11,0.156 10 6 5.086,0.705 5.196,0.862 0.11,0.156 10 5 1.927,0.705 2.06,0.861 0.133,0.156 10 3 1.662,0.804 1.847,0.96 0.185,0.156 10 SI 5.27,0.927 5.454,1.083 0.185,0.156 10 SI 5.252,2.111 5.495,2.267 0.244,0.156 10 +S 0.169,8.226 1.921,8.375 1.752,0.149 10 *4: for Radio Receiver Type 0.169,8.54 3.091,8.689 2.922,0.149 10 *5: w/ TOYOTA Parking Assist-sensor System 0.169,7.89 2.122,8.053 1.953,0.163 10 *3: for Radio and Display Type 0.169,7.278 2.241,7.427 2.072,0.149 10 *1: for Automatic Cooler System 4.959,2.748 6.806,2.904 1.847,0.156 10 Combination Meter Assembly 5.589,5.348 5.898,5.504 0.309,0.156 10 SPD 5.912,6.065 6.277,6.221 0.366,0.156 10 ECM 4.959,2.575 5.256,2.732 0.296,0.156 10 G19 0.52,2.764 2.148,3.085 1.628,0.321 10 Air Conditioning Amplifier Assembly*1 1.948,1.961 2.072,2.117 0.124,0.156 10 9 1.534,2.145 1.844,2.301 0.309,0.156 10 SPD 0.52,2.592 0.818,2.748 0.298,0.156 10 G94 3.859,1.831 4.061,1.987 0.201,0.156 10 26 0.695,1.238 1.02,1.394 0.325,0.156 10 C38 3.853,2.028 4.077,2.185 0.225,0.156 10 2Q 3.873,5.052 4.075,5.208 0.201,0.156 10 26 3.867,5.249 4.091,5.406 0.225,0.156 10 2P 5.401,5.149 5.514,5.305 0.113,0.156 10 8 5.633,5.895 5.944,6.052 0.311,0.156 10 G88 2.971,1.838 3.192,1.995 0.22,0.156 10 10 2.961,2.048 3.185,2.204 0.225,0.156 10 2P 2.915,5.965 4.202,6.309 1.287,0.344 10 Driver Side Junction Block Assembly 3.897,3.429 4.003,3.585 0.106,0.156 10 9 3.882,3.625 4.06,3.781 0.178,0.156 10 2I 5.577,3.723 5.886,3.879 0.309,0.156 10 SPD 5.393,3.533 5.516,3.689 0.123,0.156 10 3 5.281,4.38 6.863,4.701 1.581,0.322 10 Rear Clearance Warning ECU Assembly*5 5.281,4.209 5.492,4.365 0.21,0.156 10 T1 0.5,6.794 2.285,6.95 1.786,0.156 10 Radio Receiver Assembly*4 3.007,5.062 3.113,5.218 0.106,0.156 10 4 1.936,5.171 2.12,5.328 0.184,0.156 10 17 1.578,5.355 1.887,5.511 0.309,0.156 10 SPD 0.5,6.632 0.738,6.788 0.239,0.156 10 G1 0.511,5.947 2.278,6.292 1.767,0.345 10 Radio and Display Receiver Assembly*3 0.511,5.788 0.876,5.944 0.365,0.156 10 G127 2.952,5.258 3.177,5.414 0.225,0.156 10 2Q 1.563,3.751 1.872,3.907 0.309,0.156 10 SPD 3.014,3.454 3.114,3.61 0.1,0.156 10 4 2.961,3.65 3.185,3.806 0.225,0.156 10 2P 1.917,3.555 2.101,3.712 0.184,0.156 10 15 0.385,4.18 0.766,4.336 0.381,0.156 10 G124 0.385,4.347 2.397,4.53 2.012,0.182 10 Theft Warning ECU Assembly*2 0.169,7.581 2.044,7.73 1.875,0.149 10 *2: w/ Theft Deterrent System

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2Q and 2P and 2I driver side junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

E271743
0.885,0.167 1.302,0.417 0.417,0.25 3.333,0.167 3.75,0.417 0.417,0.25 5.75,0.167 6.167,0.417 0.417,0.25 0.083,0.052 0.552,0.292 0.469,0.24 10 false *a 1,0.208 1.469,0.448 0.469,0.24 10 false 2Q 3.458,0.208 3.927,0.448 0.469,0.24 10 false 2P 5.896,0.208 6.365,0.448 0.469,0.24 10 false 2I
*a Front view of wire harness connector
(to Junction Connector)
- -


HINT:

If the voltage is not as specified, it is possible that an ECU or circuit has a malfunction.

The malfunctioning ECU or circuit will be diagnosed in the following steps.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
2Q-4 - Body ground*1 Ignition switch ON 4.5 to 14 V
2P-10 - Body ground*2 Ignition switch ON 4.5 to 14 V
2P-26 - Body ground Ignition switch ON 4.5 to 14 V
2I-9 - Body ground*3 Ignition switch ON 4.5 to 14 V
2P-4 - Body ground*4 Ignition switch ON 4.5 to 14 V


*1: w/ Audio and Visual System

*2: for Automatic Cooler System

*3: w/ TOYOTA Parking Assist-sensor System

*4: w/ Theft Deterrent System


Result:
Result Proceed to
Voltage is not as specified in one circuit A
Voltage is as specified in all circuits B




A

2.SYSTEM CHECK

B

4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
2.SYSTEM CHECK
a.

Select the circuit for which the voltage was not as specified in the previous step.

Result:
Tester Connection System that Uses the Circuit Proceed to
2Q-4 - Body ground*1 Audio and visual system A
2P-10 - Body ground*2 Automatic cooler system B
2P-26 - Body ground SFI system C
2I-9 - Body ground*3 TOYOTA parking assist-sensor system D
2P-4 - Body ground*4 Theft Deterrent System E


*1: w/ Audio and Visual System

*2: for Automatic Cooler System

*3: w/ TOYOTA Parking Assist-sensor System

*4: w/ Theft Deterrent System




A

3.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - RADIO RECEIVER OR RADIO AND DISPLAY RECEIVER)

B

6.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

C

7.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)

D

8.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - REAR CLEARANCE WARNING ECU ASSEMBLY)

E

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - THEFT WARNING ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - RADIO RECEIVER OR RADIO AND DISPLAY RECEIVER)

*1: for Radio Receiver Type

*2: for Radio and Display Type


a.

Disconnect the 2Q driver side junction block assembly connector.


b.

Disconnect the G1 radio receiver assembly connector*1 or the G127 radio and display receiver assembly connector*2.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2Q-4 - G1-17 (SPD)*1 Always Below 1 Ω
G1-17 (SPD) - Body ground*1 Always 10 kΩ or higher
2Q-4 - G127-17 (SPD)*2 Always Below 1 Ω
G127-17 (SPD) - Body ground*2 Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK (for Radio Receiver Type) B
OK (for Radio and Display Type) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE RADIO RECEIVER ASSEMBLY

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the 2Q driver side junction block assembly connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2Q-26 - G19-6 (+S) Always Below 1 Ω
G19-6 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK COMBINATION METER ASSEMBLY
a.

Check the output waveform.

i.
E224603
1.271,0.646 1.688,0.896 0.417,0.25 1.792,1.438 2.167,0.802 2.167,0.802 2.354,0.802 true 0.104,0.125 0.5,0.375 0.396,0.25 10 false *a 1.344,0.688 1.74,0.938 0.396,0.25 10 false G19 2.438,0.729 2.833,0.979 0.396,0.25 10 false +S 2.938,3.625 3.333,3.875 0.396,0.25 10 false GND
*a Component with harness connected
(Combination Meter Assembly)


Reconnect the G19 combination meter assembly connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal G19-6 (+S) and body ground.


iv.

Turn the ignition switch to ON.


v.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G19-6 (+S) - Body ground
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Driving at approx. 20 km/h (12 mph)

OK:

The waveform displayed is as shown in the illustration.


HINT:

As the engine speed increases, the wavelength shortens.




Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the 2P driver side junction block assembly connector.


b.

Disconnect the G94 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-10 - G94-9 (SPD) Always Below 1 Ω
G94-9 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the 2P driver side junction block assembly connector.


b.

Disconnect the G88 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-26 - G88-8 (SPD) Always Below 1 Ω
G88-8 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - REAR CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the 2I driver side junction block assembly connector.


b.

Disconnect the T1 rear clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2I-9 - T1-3 (SPD) Always Below 1 Ω
T1-3 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR CLEARANCE WARNING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - THEFT WARNING ECU ASSEMBLY)
a.

Disconnect the 2P driver side junction block assembly connector.


b.

Disconnect the G124 theft warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-4 - G124-15 (SPD) Always Below 1 Ω
G124-15 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR