Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE
RM1880E _54 Brake _013230 PARKING BRAKE _0068575 PARKING BRAKE CABLE A

PARKING BRAKE  PARKING BRAKE CABLE  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

C237699
3.406,5.313 3.406,6.135 false 2.719,0.49 2.719,0.281 2.719,0.281 2.448,0.281 true 3.344,6.167 3.635,6.438 0.292,0.271 10 false *1 2.281,0.208 2.531,0.469 0.25,0.26 10 false *2
*1 No. 3 Parking Brake Cable *2 No. 3 Clip


a.

Install the No. 3 parking brake cable with the 4 bolts and nut.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


b.

Install the No. 3 clip.


c.

Connect the No. 3 parking brake cable to the parking brake shoe lever LH and backing plate LH.

i.

Connect the No. 3 parking brake cable to the backing plate with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Connect the No. 3 parking brake cable to the parking brake shoe lever (See page Brake>BRAKE (REAR)>REAR BRAKE>REASSEMBLY).



Hide 2.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

C237698
4.583,2.323 4.583,3.01 4.583,3.01 3.969,3.01 true 1.052,2.5 1.052,3.375 true 3.771,2.906 3.979,3.094 0.208,0.188 10 false *1 0.99,3.375 1.198,3.594 0.208,0.219 10 false *2
*1 No. 2 Parking Brake Cable *2 Parking Brake Equalizer


a.

Install the No. 2 parking brake cable with the 4 bolts.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


b.

Connect the No. 2 parking brake cable to the parking brake shoe lever RH and backing plate RH.

i.

Connect the No. 2 parking brake cable to the backing plate with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Connect the No. 2 parking brake cable to the parking brake shoe lever (See page Brake>BRAKE (REAR)>REAR BRAKE>REASSEMBLY).

HINT:

Use the same procedure described for the LH side.




c.

Connect the No. 2 parking brake cable to the parking brake equalizer and apply MP grease to the connecting portion.


d.

Install the No. 2 heat insulator with the 2 bolts.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 3.INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY

C237697
3.063,3.104 2.479,1.75 2.479,1.75 1.833,1.75 true 3.75,0.51 1.854,0.51 true 5.615,2.583 5.615,2.333 5.615,2.333 5.302,2.333 false 3.792,1.833 2.854,0.917 2.854,0.917 1.885,0.917 true 1.635,1.677 1.844,1.875 0.208,0.198 10 false *1 1.677,0.813 1.896,1 0.219,0.188 10 false *2 1.677,0.417 1.875,0.594 0.198,0.177 10 false *3 5.104,2.25 5.313,2.438 0.208,0.188 10 false *4
*1 No. 1 Parking Brake Cable *2 No. 3 Parking Brake Cable
*3 Parking Brake Equalizer *4 Cable Support Bracket


a.

Connect the No. 1 parking brake cable to the parking brake lever (See page Brake>PARKING BRAKE>PARKING BRAKE LEVER>INSTALLATION).


b.

Install the No. 1 parking brake cable clamp to the No. 1 parking brake cable.


c.

Install the No. 1 parking brake cable with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the No. 1 parking brake cable to the parking brake equalizer and apply MP grease to the connecting portion.


e.

Connect the No. 1 parking brake cable to the No. 3 parking brake cable.


f.

Install the pin and No. 1 clip.


g.

Attach the No. 1 parking brake cable to the cable support bracket.


h.

Install the No. 1 heat insulator with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 4.CHECK REAR BRAKE DRUM INSTALLATION

Hide 5.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY AND NEW GASKET

Hide 6.ADJUST PARKING BRAKE

Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).