Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068664 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E173197

Remove the bolt and disconnect the suction hose sub-assembly.

NOTICE:
E173198
1.813,0.906 2,1.104 0.188,0.198 10 false *a
*a Disconnect tube by hand


·

Do not use a screwdriver or similar tool to disconnect the suction hose sub-assembly.


·

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.




b.

Remove the O-ring from the suction hose sub-assembly.


Hide 6.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Disconnect the air conditioning tube and accessory assembly.

NOTICE:
·

Do not use a screwdriver or similar tool to disconnect the air conditioning tube and accessory assembly.

·

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.




b.

Remove the O-ring from the air conditioning tube and accessory assembly.


Hide 7.REMOVE HEATER WATER INLET HOSE

E225468

a.

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.

HINT:

Collect the engine coolant in a container.



Hide 8.REMOVE HEATER WATER OUTLET HOSE

E225469

a.

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.

HINT:

Collect the engine coolant in a container.



Hide 9.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 10.REMOVE NO. 3 HEATER TO REGISTER DUCT

E231875

a.

Remove the 2 clips.


b.

Detach the 4 claws and remove the No. 3 heater to register duct.


Hide 11.REMOVE NO. 1 HEATER TO REGISTER DUCT

E231876

a.

Remove the 2 clips.


b.

Detach the 2 claws and remove the No. 1 heater to register duct.


Hide 12.REMOVE NO. 2 HEATER TO REGISTER DUCT

E231877

a.

Remove the clip.


b.

Detach the 2 claws and remove the No. 2 heater to register duct.


Hide 13.REMOVE NO. 5 HEATER TO REGISTER DUCT

E231878

a.

Detach the 8 claws and remove the No. 5 heater to register duct.


Hide 14.REMOVE DEFROSTER NOZZLE ASSEMBLY

E231879

a.

Using a screwdriver, detach the 3 claws and remove the defroster nozzle assembly.


Hide 15.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 16.REMOVE STEERING COLUMN ASSEMBLY

Hide 17.REMOVE NO. 1 AIR DUCT

a.
E226311

Detach the 2 claws and remove the No. 1 air duct.


Hide 18.REMOVE NO. 2 AIR DUCT

a.
E226312

Detach the 2 claws and remove the No. 2 air duct.


Hide 19.REMOVE NO. 4 AIR DUCT

a.
E226313

Detach the 2 claws and remove the No. 4 air duct.


Hide 20.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

E231880
2.26,1.146 2.531,1.354 0.271,0.208 10 true *1 1.552,1.927 1.75,2.083 0.198,0.156 10 false *4 0.958,1.375 1.229,1.719 0.271,0.344 10 true *2 0.719,0.281 0.927,0.563 0.208,0.281 10 true *2 1.635,0.229 1.938,0.51 0.302,0.281 10 true *3
*1 Screw
*2 Nut A
*3 Nut B
*4 Bolt


a.

Detach the 3 clamps and remove the 2 nuts labeled A.


b.

Disconnect the connectors and remove the driver side junction block.


c.

Remove the screw.


d.

Remove the bolt, the nut labeled B and the No. 1 instrument panel brace sub-assembly.


Hide 21.REMOVE AIR CONDITIONING DUCT SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E231881

Detach the 2 claws and remove the air conditioning duct sub-assembly.


Hide 23.REMOVE INSTRUMENT PANEL REINFORCEMENT

a.
E231882

Disconnect the connector and detach the clamp.


b.
E231883

for Manual Air Conditioning System:

Detach the clip and disconnect the connectors.


c.
E231884

for Automatic Air Conditioning System:

Detach the clip and disconnect the connectors.


d.
E231885

Remove the 2 bolts and disconnect the ground wires from the instrument panel reinforcement.


e.
E233029

Remove the grommet from the vehicle body.


f.

Detach the 10 clamps.

E272048


g.

Disconnect the connectors.


h.

Remove the 3 bolts.

E231888


i.

for Automatic Transmission:

Remove the 8 bolts and instrument panel reinforcement.


j.

for Manual Transmission:

Remove the 9 bolts and instrument panel reinforcement.

E231889
0.865,1.469 1.167,1.469 1.167,1.469 1.167,1.688 true 0.698,1.396 0.99,1.667 0.292,0.271 10 false *A
*A for Manual Transmission - -



Hide 24.REMOVE NO. 1 COOLER UNIT DRAIN HOSE

E231890

a.

Remove the No. 1 cooler unit drain hose.


Hide 25.REMOVE AIR CONDITIONING UNIT ASSEMBLY

E231891

a.

Remove the bolt, nut and air conditioning unit assembly.


Hide 26.REMOVE NO. 3 AIR DUCT

E231892

a.

Remove the 3 nuts and No. 3 air duct.