1.TABLE OF BOLT, SCREW AND NUT
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabetical code in the table.
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
4.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
5.REMOVE CONSOLE BOX ASSEMBLY
6.REMOVE FRONT DOOR SCUFF PLATE LH
7.REMOVE FRONT DOOR SCUFF PLATE RH
8.REMOVE COWL SIDE TRIM BOARD LH
Remove the part of the front door opening trim attached to the cowl side trim board.
Remove the clip.
Detach the 2 clips and remove the cowl side trim board.
9.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
10.REMOVE RADIO TUNER OPENING COVER (w/o Audio)
Remove the 4 screws and radio tuner opening cover.
11.REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio)
for Radio Receiver Type:
(See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL)
for Radio and Display Type:
(See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL)
12.REMOVE INSTRUMENT PANEL HOLE COVER (w/o Multi-information Display)
Remove the 2 screws <F>.
Disconnect the connectors and remove the instrument panel hole cover.
13.REMOVE ACCESSORY METER ASSEMBLY (w/ Multi-information Display)
14.REMOVE NO. 2 INSTRUMENT PANEL REGISTER BEZEL
Detach the 2 claws and remove the No. 2 instrument panel register bezel.
15.REMOVE INSTRUMENT PANEL REGISTER BEZEL
Detach the 2 claws and remove the instrument panel register bezel.
16.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
| *1 | Stopper |
Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
| *1 | Hinge |
Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
17.REMOVE NO. 1 SWITCH HOLE BASE
| *1 | Protective Tape |
Put protective tape around the No. 1 switch hole base.
Detach the 4 claws.
Disconnect the connector and remove the No. 1 switch hole base.
18.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Manual Air Conditioning System)
19.REMOVE NO. 3 HEATER TO REGISTER DUCT
20.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
for LHD:
Using a clip remover, remove the 2 clips <A>.
Remove the 2 bolts <B>, 4 nuts <C>, screw <D> and 2 screws <E>.
Disconnect the hood lock control cable, fuel lid lock control cable, DLC3 and ash receptacle light.
Disconnect the connectors and detach the clamps.
Detach the 2 guides and remove the lower instrument panel.
for Automatic Air Conditioning System:
Disconnect the room temperature sensor.
| *1 | Clip <A> | *2 | Bolt <B> |
| *3 | Nut <C> | *4 | Screw <D> |
| *5 | Screw <E> | *6 | Hood Lock Control Cable |
| *7 | Fuel Lid Lock Control Cable | *8 | DLC3 |
| *9 | Ash Receptacle Light | *10 | Clamp |
| *11 | Guide | *12 | Room Temperature Sensor |
for RHD:
Using a clip remover, remove the 2 clips <A>.
Remove the 2 bolts <B>, 4 nuts <C>, screw <D> and 2 screws <E>.
Disconnect the hood lock control cable, fuel lid lock control cable, DLC3 and ash receptacle light.
Disconnect the connectors and detach the clamps.
Detach the 2 guides.
Disconnect the room temperature sensor and remove the lower instrument panel.
| *1 | Clip <A> | *2 | Bolt <B> |
| *3 | Nut <C> | *4 | Screw <D> |
| *5 | Screw <E> | *6 | Hood Lock Control Cable |
| *7 | Fuel Lid Lock Control Cable | *8 | DLC3 |
| *9 | Ash Receptacle Light | *10 | Clamp |
| *11 | Guide | *12 | Room Temperature Sensor |
21.REMOVE GLOVE COMPARTMENT DOOR LOCK ASSEMBLY
Remove the 2 screws and glove compartment door lock.