Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL
Remove the screw.
Detach the 2 clips and 8 claws.
Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.
4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
| *A | w/ Front No. 2 Speaker |
| *B | w/o Front No. 2 Speaker |
Detach the 3 clips and remove the front door lower frame bracket garnish.
5.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the screw.
Detach the 9 clips and remove the front door trim board.
6.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
Raise the 7 claws of the front door inner glass weatherstrip as shown in the illustration, and then remove the front door inner glass weatherstrip from the front door trim board.
7.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
8.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)
9.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
10.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.
Disconnect the front door inside locking cable and front door lock remote control cable and remove the front door inside handle.
11.REMOVE FRONT DOOR NO. 1 TRIM BRACKET
Remove the 2 screws and front door No. 1 trim bracket.
12.REMOVE FRONT DOOR SERVICE HOLE COVER LH
Pull out the wire harness from the front door service hole cover.
Pull out the front door inside locking cable and front door lock remote control cable from the front door service hole cover, and then remove the front door service hole cover.
Remove any remaining butyl tape from the front door panel.
13.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Temporarily install the power window regulator master switch assembly with front door armrest base panel.
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly so that the front door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Remove the power window regulator master switch assembly with front door armrest base panel.
Remove the 2 bolts.
After the bolts are removed, do not allow the front door glass to fall.
Remove the front door glass as indicated by the arrows in the order shown in the illustration.
Do not damage the front door glass.
14.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH
15.REMOVE FRONT DOOR GLASS RUN LH
Remove the front door glass run.
16.REMOVE FRONT DOOR UPPER OUTER BLACK OUT TAPE LH
17.REMOVE FRONT DOOR REAR OUTER BLACK OUT TAPE LH
18.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
| *1 | Temporary Bolt |
Disconnect the connector.
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the front door power window regulator may fall and become damaged.
Remove the 5 bolts and front door power window regulator.
Remove the temporary bolt from the front door power window regulator.
19.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Remove the bolt.
Detach the guide and remove the front door rear lower frame.
20.REMOVE FRONT DOOR OUTSIDE HANDLE COVER
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover together with the door key cylinder.
Detach the 2 claws and remove the front door outside handle cover from the door key cylinder.
21.REMOVE FRONT DOOR LOCK ASSEMBLY LH
22.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
Remove the front door lock remote control cable.
23.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH
Detach the 3 claws and open the cover.
Remove the front door inside locking cable.
24.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
Remove the front door outside handle by sliding and pulling it in the direction indicated by the arrow in the illustration.
25.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Using a T30 "TORX" socket wrench, loosen the screw.
Detach the claw and remove the front door outside handle frame.
26.REMOVE FRONT DOOR LOCK OPEN ROD LH
| *1 | Snap |
Rotate the snap in the direction indicated by the arrow in the illustration to detach the snap from the front door lock open rod.
Remove the front door lock open rod from the front door outside handle frame.
27.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
Detach the 2 claws and remove the front door front outside handle pad.
28.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
Detach the 2 claws and remove the front door rear outside handle pad.
29.REMOVE FRONT DOOR PANEL CUSHION
Remove the 2 front door panel cushions.
30.REMOVE FRONT DOOR WEATHERSTRIP LH
Remove the double-sided tape to detach the 17 clips and remove the front door weatherstrip.
31.REMOVE FRONT DOOR OUTSIDE MOULDING LH (w/ Outside Moulding)
32.REMOVE FRONT DOOR CHECK ASSEMBLY LH
Remove the 3 bolts and front door check.