Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Remove the screw.
Detach the 2 clips and 8 claws.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
4.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the screw.
Detach the 10 clips and remove the rear door trim board.
5.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
Raise the 5 claws of the rear door inner glass weatherstrip as shown in the illustration, and then remove the rear door inner glass weatherstrip from the rear door trim board.
6.REMOVE REAR SPEAKER ASSEMBLY
7.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.
Disconnect the rear door inside locking cable and rear door lock remote control cable and remove the rear door inside handle.
8.REMOVE REAR DOOR NO. 2 TRIM BRACKET
Remove the 2 screws and rear door No. 2 trim bracket.
9.REMOVE REAR DOOR SERVICE HOLE COVER LH
Pull out the wire harness from the rear door service hole cover.
Pull out the rear door inside locking cable and rear door lock remote control cable from the rear door service hole cover, and then remove the rear door service hole cover.
Remove any remaining butyl tape from the rear door panel.
10.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.
Connect the cable to the negative (-) battery terminal.
Move the rear door glass so that the rear door glass channel can be seen.
Disconnect the cable from the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Remove the rear power window regulator switch assembly with rear door armrest base panel.
Partially remove the rear door glass run as shown in the illustration.
| *1 | Temporary Bolt |
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window division bar may fall and become damaged.
Remove the screw and bolt.
Remove the rear door window division bar together with the rear door glass run as shown in the illustration.
Remove the rear door window division bar from the rear door glass run.
11.REMOVE REAR DOOR GLASS RUN LH
Remove the front side of the rear door glass run.
12.REMOVE REAR DOOR QUARTER WINDOW GLASS LH
Remove the rear door quarter window glass.
13.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
Remove the rear door quarter window weatherstrip from the rear door quarter window glass.
14.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Remove the rear door glass from the rear door window regulator assembly as shown in the illustration.
Do not damage the door glass.
15.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH
| *1 | Protective Tape |
Using a screwdriver, remove the rear door glass channel.
Tape the screwdriver tip before use.
16.REMOVE REAR DOOR GLASS CHANNEL FILLER
Remove the rear door glass channel filler.
17.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH
18.REMOVE FRONT OUTER BLACK OUT TAPE LH
19.REMOVE UPPER OUTER BLACK OUT TAPE LH
20.REMOVE REAR OUTER BLACK OUT TAPE LH
21.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Disconnect the connector.
| *1 | Temporary Bolt |
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door power window regulator may fall and become damaged.
Remove the 3 bolts and rear door power window regulator.
Remove the temporary bolt from the rear door power window regulator.
22.REMOVE REAR DOOR LOCK ASSEMBLY LH
23.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
Remove the rear door lock remote control cable.
24.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
Detach the 3 claws and open the cover.
Remove the rear door inside locking cable.
25.REMOVE REAR DOOR OUTSIDE HANDLE COVER LH
Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle cover.
26.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
Remove the rear door outside handle by sliding and pulling it in the direction indicated by the arrow in the illustration.
27.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle frame.
28.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
Detach the 2 claws and remove the rear door front outside handle pad.
29.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
Detach the 2 claws and remove the rear door rear outside handle pad.
30.REMOVE REAR DOOR PANEL CUSHION
Remove the rear door panel cushion.
31.REMOVE REAR DOOR WEATHERSTRIP LH
Detach the 19 clips and remove the rear door weatherstrip.
32.REMOVE REAR DOOR OUTSIDE MOULDING LH (w/ Outside Moulding)
33.REMOVE REAR DOOR CHECK ASSEMBLY LH
Remove the 3 bolts and rear door check.