Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM1880E _59 Vehicle Exterior _013249 DOOR / HATCH _0068715 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door check.


b.

When reusing a bolt labeled B:

i.

Clean the threads of the bolt labeled B with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt labeled B.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B291564
1.219,1.75 1.521,1.75 false 2.052,0.51 2.052,0.26 2.052,0.26 2.49,0.26 true 2.146,1.354 2.604,1.354 true 2.563,0.156 2.885,0.375 0.323,0.219 10 false *1 2.656,1.25 2.906,1.458 0.25,0.208 10 false *1 1.021,1.667 1.302,1.896 0.281,0.229 10 true *2
*1 Bolt A
*2 Bolt B


Install the rear door check with the 2 bolts labeled A and the bolt labeled B.

Torque:
Bolt A : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Bolt B : 21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 2.INSTALL REAR DOOR OUTSIDE MOULDING LH (w/ Outside Moulding)

Hide 3.INSTALL REAR DOOR WEATHERSTRIP LH

a.

Attach the 19 clips to install the rear door weatherstrip.


Hide 4.INSTALL REAR DOOR PANEL CUSHION

a.

Install a new rear door panel cushion.


Hide 5.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the rear door rear outside handle pad.


Hide 6.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the rear door front outside handle pad.


Hide 7.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door outside handle frame.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame with the screw.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 8.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

B291628

a.

Install the rear door outside handle by moving it in the direction indicated by the arrow shown in the illustration.


Hide 9.INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

a.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 10.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the rear door inside locking cable.


b.

Attach the 3 claws to close the cover.


Hide 11.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the rear door lock remote control cable.


Hide 12.INSTALL REAR DOOR LOCK ASSEMBLY LH

Hide 13.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B291629

Apply MP grease to the sliding and rotating areas of the rear door power window regulator.


b.

Temporarily install the temporary bolt to the rear door power window regulator.


c.
B291553
2.01,0.573 2.344,0.292 true 2.406,0.156 2.688,0.365 0.281,0.208 10 false *1
*1 Temporary Bolt


Install the rear door power window regulator with the 3 bolts, and then tighten the temporary bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the rear door power window regulator as it may become damaged.



Hide 14.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.
B291630
0.344,0.146 0.667,0.344 0.323,0.198 10 false *a 0.76,0.906 1.042,1.115 0.281,0.208 10 false A
*a Front Side


Install the rear door glass channel filler to the rear door glass as shown in the illustration.

Standard:
Area Dimension
A 5.1 mm (0.201 in.)



Hide 15.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

a.

Apply soapy water to the inside of the rear door glass channel.


b.
B291631
0.333,0.146 0.646,0.344 0.313,0.198 10 false *a 0.771,0.896 1.042,1.083 0.271,0.188 10 false A
*a Front Side


Using a plastic-faced hammer, tap the rear door glass channel onto the rear door glass to install the rear door glass channel as shown in the illustration.

Standard:
Area Dimension
A 5.1 mm (0.201 in.)



Hide 21.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.

Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.


b.

Connect the cable to the negative (-) battery terminal.


c.

Operate the rear door power window regulator so that the rear door glass can be installed.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



e.

Remove the rear power window regulator switch assembly with rear door armrest base panel.


f.

Install the front side of the rear door glass run.


g.
B277839
1.375,0.906 1.594,0.906 1.594,0.906 1.625,1.042 true 1.375,0.542 1.594,0.542 1.594,0.542 1.625,0.677 true 0.458,1.156 0.583,1.156 0.583,1.156 0.698,1.563 true 0.396,1.656 0.615,1.656 0.615,1.656 0.656,1.75 true 1.146,0.802 1.427,1.021 0.281,0.219 10 false *1 1.146,0.417 1.448,0.646 0.302,0.229 10 false *1 1.281,1.938 1.552,2.135 0.271,0.198 10 false A 2.25,1.938 2.521,2.125 0.271,0.188 10 false B 0.219,1.042 0.49,1.24 0.271,0.198 10 false *1 0.167,1.552 0.458,1.76 0.292,0.208 10 false *1
*1 MP Grease


Apply MP grease to the sliding area of the rear door glass channel as shown in the illustration.

Standard:
Area Specified Condition
A 155 mm (6.10 in.)
B 30 mm (1.18 in.)



h.
B291632

Install the rear door glass channel to the rear door power window regulator as shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 22.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.

Install the rear door quarter window weatherstrip to the rear door quarter window glass.


Hide 23.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

a.

Install the rear door quarter window glass.


Hide 24.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.
B291545
1.531,1.104 1.938,0.76 true 1.99,0.635 2.26,0.854 0.271,0.219 10 false *1
*1 Temporary Bolt


Temporarily install the temporary bolt to the rear door window division bar.


b.

Align the rear door glass run with the rear door window division bar.


c.

Install the rear door window division bar with the bolt and screw, and then tighten the temporary bolt.


Hide 25.INSTALL REAR DOOR GLASS RUN LH

a.

Finish installing the rear door glass run.


Hide 26.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the rear door panel.


b.

Pass the wire harness through a new rear door service hole cover.


c.
B291633
0.646,0.354 0.5,0.531 false 2.979,0.302 2.823,0.438 false 0.677,0.26 0.917,0.438 0.24,0.177 10 true *a 3,0.219 3.219,0.396 0.219,0.177 10 true *a
*a Reference Point


Pass the rear door inside locking cable and rear door lock remote control cable through a new rear door service hole cover, and then attach the rear door service hole cover using the reference points on the rear door panel.

NOTICE:
·

Securely install the rear door service hole cover to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the rear door service hole cover.

·

After installing the rear door service hole cover, check the seal quality.




Hide 27.INSTALL REAR DOOR NO. 2 TRIM BRACKET

a.

Install the rear door No. 2 trim bracket with the 2 screws.


Hide 28.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B291634

Connect the rear door inside locking cable and rear door lock remote control cable to the rear door inside handle.


b.

Attach the 2 guides as indicated by the arrow in the illustration, and then attach the claw to install the rear door inside handle.


Hide 30.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B291635

Install the rear door inner glass weatherstrip to the rear door trim board and fold down the 5 claws in the directions indicated by the arrows in the illustration.


Hide 31.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.

Attach the 10 clips to install the rear door trim board.


b.

Install the screw.


Hide 32.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.

Attach the 2 claws and 8 clips to install the rear power window regulator switch assembly with rear door armrest base panel.


Hide 33.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).