2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0171 System Too Lean (Bank 1)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trim.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and change in operating environment cause the short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
If both the short-term and long-term fuel trim are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and stores a DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0171
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2-trip detection logic).
  1. Intake system
  2. Fuel pressure
  3. Fuel injector blockage
  4. Mass air flow meter
  5. Engine coolant temperature sensor
  6. Gas leakage from exhaust system
  7. Open or short in heated oxygen sensor circuit
  8. Air fuel ratio sensor
  9. Air fuel ratio sensor heater
  10. Air fuel ratio sensor heater circuits
  11. PCV hose connections
  12. PCV valve and hose
  13. ECM
P0172
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2-trip detection logic).
  1. Fuel injector leakage or blockage
  2. Fuel pressure
  3. Mass air flow meter
  4. Engine coolant temperature sensor
  5. Ignition system
  6. Gas leakage from exhaust system
  7. Open or short in heated oxygen sensor circuit
  8. Air fuel ratio sensor
  9. Air fuel ratio sensor heater
  10. Air fuel ratio sensor heater circuits
  11. Ignition system
  12. ECM

HINT:
  1. When DTC P0171 is stored, the actual air fuel ratio is too lean. When DTC P0172 is stored, the actual air fuel ratio is too rich.
  2. If the vehicle runs out of fuel, the air fuel ratio becomes lean and DTC P0171 may be stored. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within 20% of the central value (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
If the average fuel trim learned value is +35% or more, or -35% or less, the ECM interprets this as a fuel system malfunction.
A121607E10

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

Result 
Result
Proceed to
DTC P0171 or P0172 is output
A
DTC P0171 or P0172 and other DTCs are output
B

HINT:
If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIR FUEL RATIO CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the "Control the Injection Volume for A/F Sensor" operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the output voltages of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

Result:
The air fuel ratio sensor reacts in accordance with increases and decreases in the fuel injection volume:
+12.5% = Rich output:
Higher than 3.4 V
-12.5% = Lean output:
Below 3.1 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

Case
Air Fuel Ratio Sensor
Output Voltage
Heated Oxygen Sensor
Output Voltage
Main Suspected Trouble Area
1
A162605E23
A162598E15
-
2
A162596E18
A162598E15
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A162596E18
A162596E18
  1. Fuel pressure
  2. Gas leakage from exhaust system
    (air fuel ratio extremely lean or rich)
  1. Following the "Control the Injection Volume for A/F Sensor" procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio sensor and heated oxygen sensor.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2.
Result 
Result
Proceed to
Case 1
A
Case 2
B
Case 3
C


B
Go to step 14

C
Go to step 6
A


3. CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
Go to step 6
YES


4. PERFORM CONFIRMATION DRIVING PATTERN
A128471E13
  1. Connect the intelligent tester to the DLC3 (Procedure "A").

  1. Turn the ignition switch to ON (Procedure "B").

  1. Turn the tester on (Procedure "C").

  1. Clear the DTCs (Click here) (Procedure "D").

  1. Switch the ECM from normal mode to check mode (Click here) (Procedure "E").

  1. Start the engine (Procedure "F").

  1. Allow the engine to idle until the engine coolant temperature reaches 40°C (104°F) (Procedure "G").

  1. Drive the vehicle at a vehicle speed of more than 40 km/h (25 mph) for 35 seconds or more (Procedure "H").

  1. Allow the engine to idle for 40 seconds or more (Procedure "I").

  1. Repeat procedures "G" and "I" described above at least 3 times (Procedure "J").

  1. Allow the engine to idle for 40 seconds or more (Procedure "K").

    HINT:
    The MIL is illuminated during procedure "K" if a malfunction still exists.

    NOTICE:
    If the conditions in this test are not strictly followed, malfunctions may not be detected.


NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC is not output
    B



B
SYSTEM IS OK
A


6. CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leakage.

    OK:
    No gas leakage.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


7. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
Go to step 21
OK


8. INSPECT FUEL INJECTOR ASSEMBLY (INJECTION VOLUME)
  1. Check the fuel injection volume (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


9. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


10. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  1. Read Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


11. CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections (Click here).

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


12. CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage (Click here).

    OK:
    No leakage from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


13. CHECK IGNITION SYSTEM
  1. Inspect the ignition system (Click here).



OK
Go to step 18

NG
REPAIR OR REPLACE IGNITION SYSTEM
14. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


15. CHECK AIR FUEL RATIO SENSOR (POWER SOURCE)

  1. A100209E02
    Disconnect the air fuel ratio sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C56-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 20
OK


16. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C56-1 (HA1A) - C63-6 (HA1A)
    Always
    Below 1 Ω
    C56-3 (A1A+) - C63-7 (A1A+)
    Always
    Below 1 Ω
    C56-4 (A1A-) - C63-1 (A1A-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C56-1 (HA1A) or C63-6 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C56-3 (A1A+) or C63-7 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C56-4 (A1A-) or C63-1 (A1A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
OK


17. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


18. PERFORM CONFIRMATION DRIVING PATTERN
A128471E13
  1. Connect the intelligent tester to the DLC3 (Procedure "A").

  1. Turn the ignition switch to ON (Procedure "B").

  1. Turn the tester on (Procedure "C").

  1. Clear the DTCs (Click here) (Procedure "D").

  1. Switch the ECM from normal mode to check mode (Click here) (Procedure "E").

  1. Start the engine (Procedure "F").

  1. Allow the engine to idle until the engine coolant temperature reaches 40°C (104°F) (Procedure "G").

  1. Drive the vehicle at a vehicle speed of more than 40 km/h (25 mph) for 35 seconds or more (Procedure "H").

  1. Allow the engine to idle for 40 seconds or more (Procedure "I").

  1. Repeat procedure "G" and "I" described above at least 3 times (Procedure "J").

  1. Allow the engine to idle for 40 seconds or more (Procedure "K").

    HINT:
    The MIL is illuminated during procedure "K" if a malfunction still exists.

    NOTICE:
    If the conditions in this test are not strictly followed, malfunctions may not be detected.


NEXT


19. CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

Result 
Result
Proceed to
DTC is not output
A
DTC P0171 or P0172 is output
B


B
REPLACE ECM (Click here)
A

END

20. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY [A/F RELAY])
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the integration relay (A/F relay) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C56-2 (+B) - 1B-8
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C56-2 (+B) or 1B-8 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY [A/F RELAY])
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)

21. CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage (Click here).

    OK:
    No leaks or blockage.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 5 Door)
    B
    OK (for 3 Door)
    C



B
REPLACE FUEL PUMP (Click here)

C
REPLACE FUEL PUMP (Click here)
A

REPAIR OR REPLACE FUEL LINE


← P0136 Oxygen Sensor Circuit (Bank 1 Sensor 2) (+ P0137, P0138) (from Aug 2014)P0171 System Too Lean (Bank 1) (+ P0172) (from Aug 2014) →