2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Air Conditioning Compressor Magnetic Clutch Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the air conditioning amplifier assembly is turned ON, a magnet clutch assembly ON signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the A/C COMP relay turns on to operate the magnet clutch assembly.

WIRING DIAGRAM

E198320E09

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. INSPECT MAGNET CLUTCH RELAY (A/C COMP)

  1. E145138
    Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE MAGNET CLUTCH RELAY (A/C COMP)
OK


2. INSPECT COOLER COMPRESSOR ASSEMBLY

  1. E198321E05
    for 1GR-FE:Remove the cooler compressor assembly (Click here).

  1. for 1KD-FTV:Remove the cooler compressor assembly (Click here).

  1. for 2TR-FE:Remove the cooler compressor assembly (Click here).

  1. Disconnect the A magnet clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (MG+) - A-1
    Always
    Below 1 Ω
    3 (MG+) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1KD-FTV)
    C
    NG (for 2TR-FE)
    D



B
REPLACE COOLER COMPRESSOR ASSEMBLY (Click here)

C
REPLACE COOLER COMPRESSOR ASSEMBLY (Click here)

D
REPLACE COOLER COMPRESSOR ASSEMBLY (Click here)
A


3. INSPECT MAGNETIC CLUTCH ASSEMBLY

  1. E198322E01
    Reconnect the A magnet clutch connector.

  1. Apply battery voltage to the magnet clutch assembly and check the operation of the magnet clutch assembly.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MG+)
    Battery negative (-) → Body ground
    Magnet clutch assembly operating sound can be heard, and magnetic clutch hub and rotor lock.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1KD-FTV)
    C
    NG (for 2TR-FE)
    D



B
REPLACE MAGNET CLUTCH ASSEMBLY (Click here)

C
REPLACE MAGNET CLUTCH ASSEMBLY (Click here)

D
REPLACE MAGNET CLUTCH ASSEMBLY (Click here)
A


4. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)

  1. E202209E01
    Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A/C COMP relay terminal 1 - Body ground
    Ignition switch ON
    11 to 14 V
    A/C COMP relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    A/C COMP Relay
    *a
    Component without relay installed
    (Engine Room No. 1 Relay Block, Junction Block)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

  1. E177002E90
    Disconnect the G25 amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G25-20 (MGC) - Body ground
    Ignition switch off
    Below 1 V
    G25-20 (MGC) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - COOLER COMPRESSOR)
  1. Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.

  1. Disconnect the C39 compressor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A/C COMP relay terminal 3 - C39-3 (MG+)
    Always
    Below 1 Ω
    C39-3 (MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Blower Motor Circuit (from Aug 2014)Air Conditioning Compressor Magnetic Clutch Circuit (from Aug 2014) →