2013-2015 Land Cruiser Prado · Service Manual Brake

C1401 Front Speed Sensor RH Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for brake control.
The speed sensor rotors have rows of alternating N and S magnetic poles and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.

HINT:
When the connectors between the speed sensor and skid control ECU are connected, the following waveform is output.

C173114E04
DTC Code
DTC Detection Condition
Trouble Area
C1401
C1402
One of the following conditions is met:
  1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that from the other sensors for 15 seconds or more.
  2. At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
  3. At a vehicle speed of 10 km/h (6 mph) or more, the outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.
  1. Front speed sensor RH/LH
  2. Front speed sensor rotor RH/LH
  3. Sensor installation
C1271
C1272
Stored only during test mode.
  1. Front speed sensor RH/LH
  2. Front speed sensor rotor RH/LH
  3. Sensor installation

HINT:
  1. DTC C1401 is for the front speed sensor RH.
  2. DTC C1402 is for the front speed sensor LH.


INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal after cleaning or replacement (Click here).


1. CHECK FRONT SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C144929E49
    Check the speed sensor installation (Click here).
    Text in Illustration 
    *1
    Front Speed Sensor
    *a
    No clearance
    *b
    OK
    *c
    NG

    OK:
    There is no clearance between the sensor and the front steering knuckle.
    The installation bolt is tightened properly.



NG
INSTALL FRONT SPEED SENSOR CORRECTLY (Click here)
OK


2. INSPECT FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


3. INSPECT FRONT SPEED SENSOR ROTOR
  1. Remove the front axle with ABS rotor bearing assembly (Click here).

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    HINT:
    The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.
    If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.



NG
CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR
OK


4. READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
  1. Turn the ignition switch off

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front speed sensor RH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    Front speed sensor LH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE FRONT SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Click here).


NEXT


6. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

    HINT:
    The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.
    If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.



B
REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY (Click here)
A

END


← C1401 Front Speed Sensor RH Malfunction (+ C1271, C1272, C1402) (Aug 2013 – Jul 2014)C1403 Rear Speed Sensor RH Malfunction (+ C1273, C1274, C1404) (Aug 2013 – Jul 2014) →