2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. If the auto up/down function does not operate, the cause may be one or more of the following:
  1. The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.
  2. The rear power window regulator switch has a malfunction.
  3. The Hall IC in the power window regulator motor has a malfunction.
  4. There is an open or short in the wiring between the rear power window regulator switch and power window regulator motor.

WIRING DIAGRAM

B240839E09

INSPECTION PROCEDURE

HINT:
Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC B2311 is output
    B
    DTC B2312 is output
    C
    DTC B2313 is output
    D



B
GO TO DTC B2311 (Click here)

C
GO TO DTC B2312 (Click here)

D
GO TO DTC B2313 (Click here)
A


2. CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)
  1. Check that the manual up/down function using the rear power window regulator switch can operate the rear power window regulator motor (Click here).

    OK:
    Manual up/down function operates.



NG
GO TO "Rear Power Window RH does not Operate with Rear Power Window Switch RH" (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH)
  1. Use the Data List to check if the power window regulator is functioning properly (Click here).

    RR-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door P/W Auto SW
    Rear power window RH auto up/down signal / ON or OFF
    ON: Rear power window RH auto up/down switch operated
    OFF: Rear power window RH switch not operated
    -

    OK:
    On tester screen, item changes between ON and OFF according to above chart.



NG
Go to step 4
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

4. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

  1. B215963E18
    Remove the rear power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (AUTO) - 1 (GND)
    Auto up/down operation
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH RH - REAR POWER WINDOW REGULATOR MOTOR RH AND BODY GROUND)
  1. Disconnect the L2 rear power window regulator switch connector.

  1. Disconnect the L4 power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L2-8 (AUTO) - L4-4 (AUTO)
    Always
    Below 1 Ω
    L2-1 (GND) - Body ground
    Always
    Below 1 Ω
    L2-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)


← Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH (Aug 2013 – Jul 2014)All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter (Aug 2013 – Jul 2014) →