Illumination Circuit
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.WIRING DIAGRAM


INSPECTION PROCEDURE
- CAUTION:
- The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK ILLUMINATION |
Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
Result Result
Proceed to
Illumination comes on for all components except steering pad switch assembly.
A
Illumination comes on for all components except navigation receiver assembly.
B
Illumination comes on for all components except steering pad switch assembly and navigation receiver assembly.
C
No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.).
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY) |
Disconnect the spiral cable sub-assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G40-12 (IL+2) - Body ground
Light control switch tail or head position
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Spiral Cable Sub-assembly)
|
|
||||
| OK | |
| 3. INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly (Click here).
Inspect the steering pad switch assembly (Click here).
|
|
||||
| OK | |
| 4. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Remove the spiral cable sub-assembly (Click here).
Inspect the spiral cable sub-assembly (Click here).
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY) |
Disconnect the H61 navigation receiver assembly connector.
Disconnect the G40 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H61-23 (SWG) - G40-4 (EAU)
Always
Below 1 Ω
H61-23 (SWG) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL) |
Disconnect the navigation receiver assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H60-7 (GND1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
H60-10 (ILL+) - Body ground
Light control switch in the tail or head position
11 to 14 V
| *a |
Front view of wire harness connector (to Navigation Receiver Assembly) |
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND) |
Disconnect the G40 spiral cable sub-assembly connector.
Disconnect the G163 driving support switch control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G40-10 (GND1) - G163-14 (SWI2)
Always
Below 1 Ω
G163-7 (GND) - Body ground
Always
10 kΩ or higher
G163-14 (SWI2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
