B2603 Tilt and Telescopic Manual Switch Circuit Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Different voltage values are input to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should be moved based on the voltage value.| DTC Code |
Detection Condition |
Trouble Area |
| B2603 |
When operating the tilt and telescopic switch, an abnormal voltage value is input to the multiplex tilt and telescopic ECU. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (TILT UP/DOWN SWITCH, TELESCO SHORT/LONG SWITCH) |
Use the Data List to check if the tilt and telescopic switch is functioning properly.
Tilt & Telescopic Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Tilt Up Switch
Input state of tilt up by manual switch/ON or OFF
ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch
-
Tilt Down Switch
Input state of tilt down by manual switch/ON or OFF
ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch
-
Telesco Short Switch
Input state of telescopic short by manual switch/ON or OFF
ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch
-
Telesco Long Switch
Input state of telescopic long by manual switch/ON or OFF
ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch
-
- OK:
- "ON" is displayed on the intelligent tester screen for each switch that is turned on.
- "OFF" is displayed on the intelligent tester screen for each switch that is turned off.
|
|
||||
| OK | |
| 2. CONFIRM DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - HEADLIGHT DIMMER SWITCH OR WINDSHIELD WIPER SWITCH) |
Disconnect the G116 multiplex tilt and telescopic ECU connector.
Disconnect the G44 headlight dimmer switch or G120 windshield wiper switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for Headlight Dimmer Switch LH Side Type:
Tester Connection
Condition
Specified Condition
G116-4 (VC) - G44-8 (VC)
Always
Below 1 Ω
G116-3 (MSW) - G44-10 (MSW)
G44-8 (VC) - Body ground
Always
10 kΩ or higher
G44-10 (MSW) - Body ground
- for Headlight Dimmer Switch RH Side Type:
Tester Connection
Condition
Specified Condition
G116-4 (VC) - G120-12 (VC)
Always
Below 1 Ω
G116-3 (MSW) - G120-13 (MSW)
G120-12 (VC) - Body ground
Always
10 kΩ or higher
G120-13 (MSW) - Body ground
|
|
||||
| OK | |
| 4. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE) |
Reconnect the G116 multiplex tilt and telescopic ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G116-4 (VC) - G116-3 (MSW)
Engine switch on (IG)
4.9 to 5.1 V
Text in Illustration *a
Component with harness connected
(Multiplex Tilt and Telescopic ECU)
|
|
||||
| OK | |
| 5. CHECK TILT AND TELESCOPIC SWITCH |
Remove the tilt and telescopic switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 3
Tilt up
342 to 378 Ω
Tilt down
1890.5 to 2089.5 Ω
Telescopic contract
750.5 to 829.5 Ω
Telescopic extend
152 to 168 Ω
Result Result
Proceed to
NG
A
OK
for Headlight Dimmer Switch LH Side Type
B
for Headlight Dimmer Switch RH Side Type
C
Text in Illustration *a
Component without harness connected
(Tilt and Telescopic Switch)
|
|
||||
|
|
||||
| A | ||
| ||
