2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. REMOVE REAR NO. 2 SEAT ASSEMBLY LH
  1. for Manual Seat Type:
    Remove the rear No. 2 seat assembly LH (Click here).

  1. for Power Seat Type:
    Remove the rear No. 2 seat assembly LH (Click here).

  1. for Face to Face Seat Type:
    Remove the rear No. 2 seat assembly LH (Click here).


2. REMOVE REAR SEATBACK ASSEMBLY LH (for 60/40 Split Double-folding Seat Type LH Side)
  1. Remove the rear seatback assembly (Click here).


3. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

B238730E01

HINT:
Use the same procedure for all rear No. 1 floor step covers.

  1. Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


4. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

B238731
  1. Remove the 2 bolts and quarter scuff plate.


5. REMOVE REAR DOOR SCUFF PLATE LH

B238733E01
  1. Put protective tape around the rear door scuff plate.

  1. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Partially remove the rear door opening trim weatherstrip so that the front quarter trim panel assembly LH and deck trim side panel assembly LH can be removed (Click here).


7. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

B240044

HINT:
Use the same procedure for the other front luggage compartment trim cover.

  1. Detach the 4 claws and remove the cap.

  1. B238749E01
    Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker


8. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

B238750
  1. Detach the clip and remove the No. 1 deck board.


9. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

B238748
  1. Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.


10. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

B238764
  1. Remove the 3 bolts and floor side rail.


11. REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

HINT:
Use the same procedure described for the LH side.


12. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

  1. Detach the 4 claws and remove the rear floor carpet.

    B238751E01

    Text in Illustration 
    *A
    w/o Deck Rail
    *B
    w/ Deck Rail
    *C
    for Face to Face Seat Type
    -
    -


13. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

B238752

HINT:
Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.

  1. Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.


14. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

B181695

HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.

  1. Remove the luggage compartment trim hook by turning it clockwise.


15. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

B238754E01

HINT:
Use the same procedure for the other No. 1 tonneau cover holder cap.

  1. Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


16. REMOVE FRONT DECK SIDE TRIM COVER LH (w/ Tonneau Cover)

B240051E01

HINT:
Use the same procedure for the other front deck side trim cover.

  1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


17. REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

B238757E01

HINT:
Use the same procedure for all assist grip plugs.

  1. Using a screwdriver, detach the 2 claws and remove the assist grip plug.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


18. REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

  1. w/o Rear No. 2 Seat:

    1. B238753
      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    2. B238756
      Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

    3. Remove the 4 bolts and 2 screws.

    4. Detach the 5 clips and 8 claws.

    5. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

      B238755

  1. w/ Rear No. 2 Seat:

    1. B238753
      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    2. B238759
      Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

    3. Remove the 2 bolts and 2 screws.

    4. Detach the 4 clips and 8 claws and remove the deck trim side panel.

      B238760


19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

  1. B238753
    w/o Rear No. 2 Seat:

    1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    2. B238756
      Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

    3. Remove the 4 bolts and 2 screws.

    4. Detach the 5 clips and 8 claws.

    5. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

      B238755

  1. w/ Rear No. 2 Seat:

    1. B238753
      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    2. B240052
      Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

    3. B240055
      for RH Side:
      Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

    4. Detach the 4 clips and 8 claws and remove the deck trim side panel.

      B238760


20. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

B238745
  1. Move the rear shoulder belt anchor adjuster to the lowest position.

  1. Detach the 2 clips and 2 guides.

  1. Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.


21. REMOVE REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY LH (for 60/40 Split Double-folding Seat Type LH Side)

B237984
  1. Remove the 2 bolts.

  1. Detach the claw and remove the striker.

    NOTICE:
    Do not wipe off the grease on the sliding portion of the striker.


22. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B241717
    Remove the nut and rear No. 1 seat outer belt shoulder anchor.

  1. B241718
    Remove the 2 bolts and rear No. 1 seat outer belt assembly.

← REMOVAL (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →