C1A4B Stop Light Relay Circuit
Diagnostic trouble codes · Vehicles built from Aug 2013
DESCRIPTION
The skid control ECU outputs a stop light operation signal to the stop light control ECU. When the skid control ECU detects a malfunction in the stop light circuit, the driving support ECU outputs DTC C1A4B.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1A4B |
*: Condition for skid control ECU malfunction warning signal output. When the voltage at the IG1 terminal is between 11 and 14 V and the stop light illumination output (STP0) is ON, there is no input signal to the STP2 terminal for 5 seconds or more, or when the input signals to terminals STP and STP2 are different for 5 seconds or more when the voltage at the IG1 terminal is between 11 and 14 V and the stop light illumination output (STP0) is OFF. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the driving support ECU, always replace it with a new one and be sure to perform initialization (Click here). If an ECU which was installed to another vehicle is used, the information stored in the ECU will not match the information from the vehicle, and as a result, a DTC may be stored.
- When replacing the master cylinder solenoid, perform calibration (Click here).
- HINT:
- When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).
- This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more DTCs in the CAN communication system are output.
- When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).
| 1. CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM) |
Check for DTCs (Click here).
- OK:
- Vehicle stability control system DTCs are not output.
|
|
||||
| OK | |
| 2. CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.
- OK:
Condition
Illumination Condition
Brake pedal depressed
On
Brake pedal released
Off
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Check that the stop light switch condition observed on the intelligent tester changes according to brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
|
|
||||
| OK | |
| 4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Stop Light Relay
Stop light control ECU
ECU ON/OFF
Observe the stop lights (do not come on for 2 to 5 seconds).
While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light Relay Output
Stop light control ECU output/ ON or OFF
ON: Stop light control ECU on (Stop lights on)
OFF: Stop light control ECU off (Stop lights off)
-
| Result |
Proceed to |
| When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off |
A |
| When Active Test performed, Data List item changes between ON and OFF, but stop lights do not turn on |
B |
|
|
||||
| A | |
| 5. CHECK TERMINAL VOLTAGE (STP2) |
Disconnect the A7 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A7-45 (STP2) - Body ground
Brake pedal depressed
8 to 14 V
Brake pedal released
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
|
|
||||
| OK | |
| 6. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Perform a road test.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output (for LHD)
B
DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 7. CHECK TERMINAL VOLTAGE AND RESISTANCE (+B, GND) |
Disconnect the A54 stop light control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A54-6 (+B) - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A54-8 (GND) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Stop Light Control ECU)
|
|
||||
| OK | |
| 8. CHECK TERMINAL VOLTAGE (STP) |
Disconnect the A54 stop light control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A54-5 (STP) - Body ground
Brake pedal depressed
8 to 14 V
Brake pedal released
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Stop Light Control ECU)
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL ECU - SKID CONTROL ECU) |
Disconnect the A54 stop light control ECU connector.
Disconnect the A7 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A54-1 (OUT) - A7-45 (STP2)
Always
Below 1 Ω
A54-1 (OUT) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 10. CHECK TERMINAL VOLTAGE (STP) |
Disconnect the A7 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A7-7 (STP) - Body ground
Brake pedal depressed
8 to 14 V
Brake pedal released
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 11. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL ECU) |
Disconnect the A7 skid control ECU connector.
Disconnect the A54 stop light control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A7-16 (STP0) - A54-9 (ACC)
Always
Below 1 Ω
A7-16 (STP0) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 12. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL ECU) |
Disconnect the A7 skid control ECU connector.
Disconnect the A54 stop light control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A7-45 (STP2) - A54-1 (OUT)
Always
Below 1 Ω
A7-45 (STP2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 13. REPLACE STOP LIGHT CONTROL ECU |
Temporally replace the stop light control ECU with a new or normally function one (Click here).
| NEXT | |
| 14. CHECK FOR DTC (PRE-CRASH SAFETY SYSTEM) |
Clear the DTCs (Click here).
- HINT:
- If the detection conditions are not met, the system cannot detect malfunctions.
- Pre-crash safety system:
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the intelligent tester on.
- Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Stop Light Relay
STOP light control ECU
ECU ON/OFF
Observe the stop lights (do not come on for 2 to 5 seconds).
- While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light Relay Output
STOP light control ECU output/ ON or OFF
ON: Stop light control ECU output on (Stop lights on)
OFF: Stop light control ECU output off (Stop lights off)
-
- Pre-crash safety system:
Make sure the following conditions are met:
- Radar cruise control system:
- The vehicle is being driven at a speed of approximately 50 km/h (31 mph) or more and the distance control switch is on.
- Radar cruise control system:
Check for DTCs (Click here).
- OK:
- DTCs C1A4B are not output.
|
|
||||
| OK | ||
| ||
