2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Open in One Side of CAN Branch Line

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen.
  1. Brake actuator assembly (skid control ECU)*1
  2. Master cylinder solenoid (skid control ECU)*2
  3. Four wheel drive control ECU
  4. Certification ECU (smart key ECU assembly)
  5. Power management control ECU
  6. Power steering ECU assembly
  7. Navigation receiver assembly*3
  8. Radio and display receiver assembly*4
  9. Spiral cable sub-assembly (steering angle sensor)
  10. Yaw rate sensor assembly
  11. Center airbag sensor assembly
  12. Main body ECU (multiplex network body ECU)
  1. *1: for 2TR-FE
  2. *2: for 1GR-FE, 1KD-FTV
  3. *3: w/ Navigation System (for Navigation Receiver Type) or Navigation System (for Built-in Memory)
  4. *4: w/ Navigation System (for Radio and Display Type) or w/o Navigation System

WIRING DIAGRAM

C294467E01
C294468E01
C294451E02

INSPECTION PROCEDURE

HINT:
  1. Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  2. Do not remove the combination meter assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  3. The open circuit confirmation of the combination meter assembly, ECM and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.


1. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
  1. Disconnect the A6 brake actuator assembly (skid control ECU)*1 or A7 master cylinder solenoid (skid control ECU)*2 connector.

    1. *1: for 2TR-FE
    2. *2: for 1GR-FE, 1KD-FTV

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Skid Control (ABS/VSC/TRAC)" is not displayed on the intelligent tester (for 2TR-FE)
    A
    "Skid Control (ABS/VSC/TRAC)" is not displayed on the intelligent tester (for 1GR-FE, 1KD-FTV)
    B
    Several ECUs and sensors in addition to "Skid Control (ABS/VSC/TRAC)" are displayed on the intelligent tester
    C



B
Go to step 3

C
Go to step 4
A


2. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)

  1. C199357E10
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-25 (CANH) - A6-14 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

3. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)

  1. C208652E03
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-11 (CANH) - A7-25 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid [Skid Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

4. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
  1. Disconnect the G64 main body ECU (multiplex network body ECU) connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Main Body" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Main Body" are displayed on the intelligent tester
    B



B
Go to step 6
A


5. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)

  1. C212975E07
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G64-14 (CANH) - G64-13 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

6. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the G1 center airbag sensor assembly connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Airbag" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Airbag" are displayed on the intelligent tester
    B



B
Go to step 8
A


7. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)

  1. C198952E10
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G1-13 (CANH) - G1-22 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

8. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
  1. Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Spiral cable (Steering Angle Sensor)" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the intelligent tester
    B



B
Go to step 10
A


9. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)

  1. C198943E12
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G33-4 (CANH) - G33-3 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (Click here)

10. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU)
  1. Disconnect the G53 four wheel drive control ECU connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Four Wheel Drive Control" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Four Wheel Drive Control" are displayed on the intelligent tester
    B



B
Go to step 12
A


11. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU CAN BRANCH WIRE)

  1. C213047E04
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G53-19 (CANH) - G53-20 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Four Wheel Drive Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU)
OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)

12. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU)
  1. Disconnect the G38 certification ECU (smart key ECU assembly) connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Certification (Smart)" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Certification (Smart)" are displayed on the intelligent tester
    B



B
Go to step 14
A


13. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU CAN BRANCH WIRE)

  1. C198479E10
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-9 (CANH) - G38-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU [Smart Key ECU Assembly])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CERTIFICATION ECU)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)
  1. Disconnect the G46 power steering ECU assembly connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "PPS" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "PPS" are displayed on the intelligent tester
    B



B
Go to step 16
A


15. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)

  1. C212912E06
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G46-1 (CANH) - G46-2 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)

16. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the G51 power management control ECU connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Power Management1" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Power Management1" are displayed on the intelligent tester
    B



B
Go to step 18
A


17. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU CAN BRANCH WIRE)

  1. C198951E25
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-14 (CA1H) - G51-13 (CA1L)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

18. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY)
  1. Disconnect the G52 yaw rate sensor assembly connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Yaw Rate Sensor" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Yaw Rate Sensor" are displayed on the intelligent tester (w/ Navigation System [for Navigation Receiver Type] or Navigation System [for Built-in Memory)
    B
    Several ECUs and sensors in addition to "Yaw Rate Sensor" are displayed on the intelligent tester (w/ Navigation System [for Radio and Display Type] or w/o Navigation System)
    C



B
Go to step 20

C
Go to step 21
A


19. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)

  1. C210013E05
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G52-3 (CANH) - G52-2 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR ASSEMBLY)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)

20. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY)

  1. C235416E11
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the H56*1 or H61*2 navigation receiver assembly connector.

    1. *1: w/o DRL OFF Switch
    2. *2: w/ DRL OFF Switch

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o DRL OFF Switch 
    Tester Connection
    Switch Condition
    Specified Condition
    H56-9 (CANH) - H56-10 (CANL)
    Engine switch off
    54 to 69 Ω
    w/ DRL OFF Switch 
    Tester Connection
    Switch Condition
    Specified Condition
    H61-9 (CANH) - H61-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/o DRL OFF Switch
    *B
    w/ DRL OFF Switch
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

21. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)

  1. C235416E10
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the H51 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H51-9 (CANH) - H51-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)


← Short to GND in CAN Bus Line (from Aug 2014)Open in One Side of CAN Branch Line (from Aug 2014) →