2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Short to B+ in CAN Bus Line

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  1. Short between CAN bus lines and +B
  2. Combination meter assembly
  3. Brake actuator assembly (skid control ECU)*1
  4. Master cylinder solenoid (skid control ECU)*2
  5. Main body ECU (multiplex network body ECU)
  6. Center airbag sensor assembly
  7. Spiral cable sub-assembly (steering angle sensor)*2
  8. Radio and display receiver assembly*3
  9. Four wheel drive control ECU
  10. Air conditioning amplifier assembly
  11. Power steering ECU assembly*4
  12. Network gateway ECU*5
  13. Yaw rate sensor assembly
  14. ECM*4
  15. No. 1 junction connector
  16. No. 2 junction connector
  17. No. 3 junction connector
  18. No. 4 junction connector*6
  1. *1: w/o Vehicle Stability Control System
  2. *2: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)
  3. *3: w/ Audio and Visual System (for Radio and Display Type)
  4. *4: for 1KD-FTV
  5. *5: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type)
  6. *6: for 5L-E

WIRING DIAGRAM

C292163E01
C292164E01
C292165E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)

  1. C201374E11
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G48-14 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


4. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR SIDE)

  1. C201374E11
    Disconnect the G134 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G48-14 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 25
OK


5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NOTICE:
For vehicles with a 5L-E engine, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Air Conditioning Amplifier Assembly)".

  1. C288300E70
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-5 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G134-16 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 11
OK


6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C288300E71
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-4 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G134-15 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 13
OK


7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

  1. C288300E72
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-3 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G134-14 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 15
OK


8. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

  1. C288300E73
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-8 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G134-19 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 17
OK


9. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NOTICE:
For vehicles without a TOYOTA parking assist-sensor system (for 4 sensor type), go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - ECM or No. 4 Junction Connector)".

  1. C288300E74
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-6 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G134-17 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 19
OK


10. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM OR NO. 4 JUNCTION CONNECTOR)

  1. C288300E75
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-2 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G134-13 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1KD-FTV)
    B
    NG (for 5L-E)
    C



B
Go to step 21

C
Go to step 23
A

REPLACE NO. 3 JUNCTION CONNECTOR

11. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


12. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)

  1. C217222E03
    Disconnect the G46 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G46-1 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G46-2 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)

13. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


14. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C216014E02
    Disconnect the G25 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G25-11 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G25-12 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

15. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


16. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU)

  1. C217223E07
    Disconnect the G53 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G53-19 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G53-20 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Four Wheel Drive Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)
OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)

17. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


18. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY)

  1. C217220E03
    Disconnect the G52 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G52-3 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G52-2 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)

19. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


20. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY ECU)

  1. C242947E09
    Disconnect the G155 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G155-16 (CA1H) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G155-15 (CA1L) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

21. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


22. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)

  1. C217225E36
    Disconnect the G58 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G58-35 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G58-36 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

23. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


24. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR)

  1. C242753E10
    Disconnect the G101 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G101-3 (CANP) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G101-2 (CANN) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE NO. 4 JUNCTION CONNECTOR

25. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


26. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C288300E76
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-1 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G132-12 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


27. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


28. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)

  1. C201374E11
    Disconnect the A72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G48-14 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 37
OK


29. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C288300E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A72-22 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Vehicle Stability Control System)
    B
    NG (w/ Vehicle Stability Control System [for Hydraulic Brake Booster])
    C



B
Go to step 31

C
Go to step 33
A


30. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C288300E78
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A72-21 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 35
OK

REPLACE NO. 1 JUNCTION CONNECTOR

31. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


32. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C217564E01
    Disconnect the A6 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-25 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A6-14 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

33. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


34. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C217218E03
    Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-11 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A7-25 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

35. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


36. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)

  1. C217223E08
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G6-39 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

37. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


38. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C288300E79
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-8 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G132-19 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


39. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NOTICE:
For vehicles without an audio and visual system (for radio and display type), go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Center Airbag Sensor Assembly)".

  1. C288300E80
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-9 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G132-20 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 43
OK


40. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C288300E81
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-5 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G132-16 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 45
OK


41. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NOTICE:
For vehicles without a vehicle stability control system (for hydraulic brake booster), go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Main Body ECU)".

  1. C288300E82
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-7 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G132-18 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 47
OK


42. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C288300E83
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-2 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G132-13 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 49
OK

REPLACE NO. 2 JUNCTION CONNECTOR

43. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


44. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)

  1. C235427E19
    Disconnect the H51 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H51-9 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H51-10 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

45. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


46. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)

  1. C217224E03
    Disconnect the G1 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G1-13 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G1-22 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

47. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


48. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)

  1. C217221E17
    Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G33-4 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G33-3 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (Click here)

49. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


50. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)

  1. C217219E06
    Disconnect the G64 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G64-14 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G64-13 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Short in CAN Bus Lines (from Aug 2014)Short to B+ in CAN Bus Line (from Aug 2014) →