INSTALLATION
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
- HINT:
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
| 1. INSTALL THEFT WARNING SIREN ASSEMBLY (for 3 Door) |
Connect the connector.
Install the guide and attach the claw.
Install the theft warning siren assembly with the 2 bolts.
- Torque:
- 5.5 N*m{ 55 kgf*cm , 49 in.*lbf }
| 2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for 3 Door) |
Connect the connector.
Attach the 9 claws and 11 clips to install the deck trim side panel.
Install the 3 bolts and 2 screws.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Install the front seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
| 3. INSTALL OUTER LAP BELT ANCHOR COVER (for 3 Door) |
- HINT:
- Use the same procedure for the other outer lap belt anchor cover.
Attach the 3 claws to install the outer lap belt anchor cover.
| 4. INSTALL QUARTER TRIM POCKET TRAY (for 3 Door) |
Attach the 6 claws and 2 guides to install the quarter trim pocket tray.
| 5. INSTALL FRONT DECK SIDE TRIM COVER (for 3 Door) |
- HINT:
- Use the same procedure for the other front deck side trim cover.
Attach the 2 claws to install the front deck side trim cover.
| 6. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (for 3 Door) |
- HINT:
- Use the same procedure for the other tonneau cover holder cap.
Attach the 2 claws to install the tonneau cover holder cap.
| 7. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for 3 Door) |
- HINT:
- Use the same procedure for the other No. 1 luggage compartment trim hook.
Install the No. 1 luggage compartment trim hook so that it is positioned horizontally.
| 8. INSTALL REAR FLOOR CARPET ASSEMBLY (for 3 Door) |
Install the rear floor carpet.
| 9. INSTALL QUARTER TRIM COVER HOLE RH (for 3 Door) |
- HINT:
- Use the same procedure described for the LH side.
| 10. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (for 3 Door) |
Attach the 6 claws to install the rear floor mat rear support plate.
Install the 5 screws.
| 11. INSTALL MAT SET PLATE COVER (for 3 Door) |
- HINT:
- Use the same procedure for all mat set plate covers.
Attach the 2 claws to install the mat set plate cover.
| 12. INSTALL TONNEAU COVER ASSEMBLY (for 3 Door) |
Install the tonneau cover.
| 13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for 3 Door) |
- HINT:
- Use the same procedure described for the LH side.
| 14. INSTALL DOOR SCUFF PLATE ASSEMBLY RH (for 3 Door) |
- HINT:
- Use the same procedure described for the LH side.
| 15. INSTALL REAR SEAT ASSEMBLY (for 3 Door) |
for 60/40 Split Tumble Seat Type LH Side:
(Click here)
for 60/40 Split Tumble Seat Type RH Side:
(Click here)
| 16. INSTALL THEFT WARNING SIREN ASSEMBLY (for 5 Door) |
Connect the connector.
Install the guide and attach the claw.
Install the theft warning siren assembly with the 2 bolts.
- Torque:
- 5.5 N*m{ 55 kgf*cm , 49 in.*lbf }
| 17. INSTALL REAR SIDE NO. 2 AIR DUCT |
Install the duct with the 2 clips and attach the clamp.
| 18. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH |
w/o Rear No. 2 Seat:
Connect each connector.
Pass the rear seatback lock control lever base through the deck trim side panel.
Attach the 5 clips and 8 claws to install the deck trim side panel.
Install the 4 bolts and screw.
Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
w/ Rear No. 2 Seat:
Connect each connector.
Attach the 4 clips and 8 claws to install the deck trim side panel.
Install the 2 bolts and screw.
Install the rear No. 2 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Install the rear No. 1 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
| 19. INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat) |
![]() ![]() |
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
| 20. INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat) |
- HINT:
- Use the same procedure for the other assist grip.
Install the assist grip with the 2 bolts.
Attach the 4 claws to close the 2 covers.
| 21. INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover) |
- HINT:
- Use the same procedure for the other front deck side trim cover.
Attach the 2 claws to install the front deck side trim cover
| 22. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover) |
- HINT:
- Use the same procedure for the other No. 1 tonneau cover holder cap.
Attach the 2 claws to install the No. 1 tonneau cover holder cap.
| 23. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
- HINT:
- Use the same procedure for the other No. 1 luggage compartment trim hook.
Install the No. 1 luggage compartment trim hook by turning it clockwise.
| 24. INSTALL REAR NO.1 SEAT OUTER LAP BELT ANCHOR COVER |
- HINT:
- Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.
Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.
| 25. INSTALL REAR FLOOR CARPET ASSEMBLY |
Attach the 4 claws to install the rear floor carpet.


Text in Illustration *A
w/o Deck Rail
*B
w/ Deck Rail
*C
for Face to Face Seat Type
-
-
| 26. INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail) |
- HINT:
- Use the same procedure described for the LH side.
| 27. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail) |
Install the floor side rail with the 3 bolts.
| 28. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat) |
Attach the 5 clips and 4 claws to install the rear floor mat rear support plate.
| 29. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat) |
Attach the clip to install the No. 1 deck board.
| 30. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat) |
![]() ![]() |
- HINT:
- Use the same procedure for the other front luggage compartment trim cover.
Install the luggage hold belt striker and front luggage compartment trim cover with the bolt.
Text in Illustration *1
Luggage Hold Belt Striker
Attach the 4 claws to install the cap.
| 31. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover.
| 32. INSTALL OUTER LAP BELT ANCHOR COVER |
- HINT:
- Use the same procedure for the other outer lap belt anchor cover.
Attach the 3 claws to install the outer lap belt anchor cover
| 33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
- HINT:
- Use the same procedure described for the LH side.
| 34. INSTALL REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure described for the LH side.
| 35. INSTALL QUARTER SCUFF PLATE INNER RH |
- HINT:
- Use the same procedure described for the LH side.
| 36. INSTALL REAR NO. 1 SEATBACK ASSEMBLY |
for 60/40 Split Double-folding Seat Type LH Side:
(Click here)
for 60/40 Split Double-folding Seat Type RH Side:
(Click here)
| 37. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat) |
- HINT:
- Use the same procedure for all rear No. 1 floor step covers.
Attach the 2 claws to install the rear No. 1 floor step cover.
| 38. INSTALL REAR NO. 2 SEAT ASSEMBLY |
for Manual Seat Type:
(Click here)
for Power Seat Type:
(Click here)
for Face to Face Seat Type:
(Click here)
| 39. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


