Multi-terrain Select Indicator Light Remains ON
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to Multi-terrain Select Indicator Light does not Come ON (Click here).WIRING DIAGRAM
Refer to Multi-terrain Select Indicator Light does not Come ON (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
| 1. CHECK LIN COMMUNICATION LINE |
Use the GTS to check if the LIN communication system is functioning normally.
Result Result
Proceed to
LIN DTC is not output
A
LIN DTC is output
B
|
|
||||
| A | |
| 2. READ VALUE USING GTS (OFF-ROAD GUIDANCE SWITCH AND DIAL SWITCH SIGNAL) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / D-SEAT SW / Data List.
Check the Data List for proper functioning of the multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch).
D-SEAT SW Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Off-road Guidance Switch
Multi-terrain select switch/ ON or OFF
ON: Switch on
OFF: Switch off
-
Dial Switch Signal 1
Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF
Switches between ON and OFF according to the ON/OFF Combination Chart (Click here)
-
Dial Switch Signal 2
Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF
-
Dial Switch Signal 3
Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF
-
- OK:
- The GTS display changes according to multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch) operation.
|
|
||||
| OK | |
| 3. INSPECT COMBINATION METER ASSEMBLY |
Perform an Active Test of the combination meter assembly using the GTS (Click here).
- OK:
- The multi-terrain select indicator light turns on or off in accordance with the Active Test operation.
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU) |
Disconnect the G156 center cluster module switch connector.
Disconnect the G162 driving support switch control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G162-8 (MTS) - G156-20 (FRE)
Always
Below 1 Ω
G162-4 (MOD1) - G156-17 (ECU)
Always
Below 1 Ω
G162-11 (MOD3) - G156-19 (DN)
Always
Below 1 Ω
G162-2 (MOD2) - G156-18 (UP)
Always
Below 1 Ω
G156-24 (E) - Body ground
Always
Below 1 Ω
G162-8 (MTS) or G156-20 (FRE) - Body ground
Always
10 kΩ or higher
G162-4 (MOD1) or G156-17 (ECU) - Body ground
Always
10 kΩ or higher
G162-11 (MOD3) or G156-19 (DN) - Body ground
Always
10 kΩ or higher
G162-2 (MOD2) or G156-18 (UP) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT CENTER CLUSTER MODULE SWITCH |
Remove the center cluster module switch (Click here).
Inspect the multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch) (Click here).
|
|
||||
| OK | ||
| ||
