Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260486 CYLINDER HEAD GASKET A

5L-E ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 17141 1.REMOVE EXHAUST MANIFOLD

Hide 13568 2.REMOVE TIMING BELT

Hide 26100 3.REMOVE DIESEL THROTTLE BODY

a.

Hide 88320 4.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 88431 5.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A226945

Remove the bolt and disconnect the generator.


b.
A121135

Remove the 4 bolts and No. 1 compressor mounting bracket.


Hide 87245A 6.DISCONNECT HEATER WATER HOSE SUB-ASSEMBLY

Hide 8.DISCONNECT WIRE HARNESS

a.

Remove the terminal cap.


b.
A229803

Remove the nut and generator wire.


c.

Disconnect the generator connector and cooler compressor connector.


d.

Detach the 4 wire harness clamps.


e.

for RHD:

i.
A229804

Detach the 5 wire harness clamps.



f.
A229805

for LHD:

i.

Detach the 4 wire harness clamps.


ii.
A229806

Detach the 3 wire harness clamps.



Hide 82715 9.REMOVE WIRING HARNESS CLAMP BRACKET (for LHD)

Hide 11201 10.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11101 12.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A057446E04
0.354,0.25 0.531,0.427 0.177,0.177 10 false 2 2.802,1.896 2.958,2.083 0.156,0.188 10 false 7 2.438,1.75 2.625,1.938 0.188,0.188 10 false 9 0.708,0.167 0.875,0.344 0.167,0.177 10 false 8 3.094,1.729 3.271,1.917 0.177,0.188 10 false 1 0.76,1.927 0.948,2.115 0.188,0.188 10 false 5 2.74,0.135 2.917,0.313 0.177,0.177 10 false 6 0.385,1.729 0.552,1.938 0.167,0.208 10 false 3 3.094,0.24 3.25,0.417 0.156,0.177 10 false 4 1.01,0.208 1.198,0.417 0.188,0.208 10 false 10 1.031,1.719 1.26,1.927 0.229,0.208 10 false 11 2.354,0.229 2.594,0.427 0.24,0.198 10 false 12 1.406,1.906 1.625,2.125 0.219,0.219 10 false 13 1.677,0.229 1.885,0.406 0.208,0.177 10 false 18 2.094,1.917 2.333,2.125 0.24,0.208 10 false 15 1.323,0.125 1.552,0.323 0.229,0.198 10 false 16 2.021,0.125 2.229,0.323 0.208,0.198 10 false 14 1.719,1.729 1.958,1.948 0.24,0.219 10 false 17

Uniformly loosen and remove the 18 cylinder head bolts in several steps in the sequence shown.

NOTICE:

Head warpage or cracking could result from removing bolts in an incorrect order.



b.

Lift the cylinder head from the dowels on the cylinder block to remove it, and place the cylinder head on wooden blocks on a workbench.

NOTICE:

Do not damage the contact surfaces of the cylinder head and cylinder block.


HINT:

If the cylinder head is difficult to lift off, pry between the cylinder head and block with a screwdriver.



Hide 11115 14.REMOVE CYLINDER HEAD GASKET