Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260498 ENGINE G

2TR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner cap sub-assembly.


b.

Remove the air cleaner filter element sub-assembly from the air cleaner case.


c.

Visually check that the air filter sub-assembly is not excessively damaged or oily.

If necessary, replace the air cleaner filter element sub-assembly.


d.

Reinstall the air cleaner filter element sub-assembly to the air cleaner case.


e.

Reinstall the air cleaner cap sub-assembly.


Hide 13750 8.INSPECT VALVE LASH ADJUSTER NOISE

a.

Rev the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the preceding inspection.

HINT:

If any defects or problems are found during the preceding inspection, perform valve lash adjuster assembly inspection (See page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).



Hide 9.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and idle it.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Standard ignition timing:

5 to 15° BTDC @ idle


HINT:

Refer to the GTS operator's manual for further details.


NOTICE:
·

When checking the ignition timing, the transmission should be in N or P.

·

Switch off all the accessories and the A/C before connecting the GTS.




v.

Check that the ignition timing advances immediately when the engine speed is increased.


vi.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.


vii.

Monitor IGN Advance.


viii.

Perform the Active Test.

Standard ignition timing:

3 to 7° BTDC @ idle


NOTICE:

When checking the ignition timing, the transmission should be in N or P.


HINT:

Refer to the GTS operator's manual for further details.




c.

When not using the GTS:

i.

Loosen the hose clamp from the throttle body side.


ii.

Remove the 3 bolts and disconnect the intake air connector.

HINT:

Move the intake air connector so that the tester probe of a timing light can be connected to the wire of the ignition coil for the No. 1 cylinder.



iii.

Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

NOTICE:

Use a timing light that detects primary signals.



iv.

Connect the intake air connector.

HINT:

Return the parts to their original positions so that the engine can be started.



v.

Start the engine and idle it.


vi.
A206183E46
1.219,0.385 1.344,0.385 1.344,0.385 1.573,0.896 true 2.073,1.896 1.938,1.896 1.938,1.896 1.771,1.479 true 0.052,0.063 0.25,0.26 0.198,0.198 10 false *a 0.938,0.292 1.24,0.49 0.302,0.198 10 false CG 2.125,1.802 2.406,1.99 0.281,0.188 10 false TC

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3

NOTICE:
·

Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

·

When checking the ignition timing, the shift lever should be in N or P.




vii.

Using the timing light, check the ignition timing.

Standard ignition timing:

3 to 7° BTDC @ idle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the ignition timing, the shift lever should be in N or P.




viii.

Remove SST from the DLC3.


ix.

Check the ignition timing.

Standard ignition timing:

5 to 15° BTDC @ idle



x.

Check that the ignition timing advances immediately when the engine speed is increased.


xi.

Turn the ignition switch off.


xii.

Disconnect the timing light from the engine.


xiii.

Connect the intake air connector with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


xiv.

Tighten the hose clamp.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 10.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and idle it.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Standard idle speed:

600 to 700 rpm


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the idling speed, the shift lever should be in N or P.



HINT:

Refer to the GTS operator's manual for further details.



v.

Turn the ignition switch off.


vi.

Disconnect the GTS from the DLC3.



c.
A206183E47
1.333,1.906 1.198,1.906 1.198,1.906 1.031,1.49 true 0.063,0.052 0.26,0.25 0.198,0.198 10 false *a 1.396,1.813 1.771,1.99 0.375,0.177 10 false TAC

When not using the GTS:

Text in Illustration
*a Front view of DLC3

i.

Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

·

Turn all the electrical systems and the A/C off.

·

When checking the idling speed, the shift lever should be in N or P.




ii.

Check the idle speed.

Standard idle speed:

600 to 700 rpm



iii.

Disconnect the tachometer probe from the DLC3.



d.

If the engine speed is not as specified, update the idle speed control (ISC) learned value using either procedure 1 or procedure 2 below, and then check the engine speed again.

i.

Procedure 1:

After completely warming up the engine, drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and idle the engine for 30 seconds or more. Repeat this pattern 5 times or more.

A172908E01
1.758,0.94 1.963,1.110 0.205,0.170 10 *a 2.893,0.94 3.098,1.110 0.205,0.170 10 *b 5.485,0.94 5.690,1.110 0.205,0.170 10 *b 4.168,0.94 4.373,1.110 0.205,0.170 10 *c 3.489,0.464 3.693,0.634 0.205,0.170 10 *d

Text in Illustration
*a Engine completely warmed up *b Vehicle being driven at 30 km/h (19 mph)
*c Idling *d 1 time


ii.

Procedure 2:

After completely warming up the engine, stop the engine and then idle it. Repeat this pattern 5 times or more.

A172909E01
0.628,0.681 0.833,0.851 0.205,0.170 10 *a 1.716,0.681 1.921,0.851 0.205,0.170 10 *b 4.612,0.681 4.816,0.851 0.205,0.170 10 *b 2.263,1.44 2.467,1.609 0.205,0.170 10 *c 5.233,1.44 5.437,1.609 0.205,0.170 10 *c 3.087,0.681 3.291,0.851 0.205,0.170 10 *d 5.88,0.681 6.084,0.851 0.205,0.170 10 *d 3.731,0.27 3.936,0.440 0.205,0.170 10 *e

Text in Illustration
*a Engine completely warmed up *b Engine stopped
*c Engine started *d Idling
*e 1 time - -

HINT:
·

Be sure to idle the engine for 150 seconds or more for each time the pattern is repeated.

·

If the engine speed is not as specified after performing the procedure above, inspect the idle speed control system as it is malfunctioning.





Hide 11.INSPECT COMPRESSION

a.

Warm up and stop the engine.



c.

Disconnect the 4 fuel injector connectors.



e.

Inspect the cylinder compression pressure.

i.

Fully open the throttle.


ii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1230 kPa (12.5 kgf/cm2, 178 psi) or higher


Minimum pressure:

880 kPa (9.0 kgf/cm2, 128 psi)


Difference between each cylinder:

98 kPa (1.0 kgf/cm2, 14.2 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression in as short a time as possible.



HINT:

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.






g.

Connect the 4 fuel injector connectors.



Hide 12.INSPECT CO/HC

a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling the engine.


d.

Check the CO/HC concentration during idling and when the engine is running at 2500 rpm.

HINT:

When doing the 2 mode (with the engine idling/ running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.



ii.

Refer to the table below for possible causes, and then inspect the applicable parts and repair them if necessary.

CO HC Problems Possible Causes
Normal High Rough idling
1.

Faulty ignition:

-

Incorrect timing

-

Plugs are contaminated or shorted, or gaps are incorrect


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leakage from intake or exhaust valves

4.

Leakage from cylinders


Low High Rough idling
(Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body with motor assembly

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idling
(Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve sub-assembly

3.

Faulty SFI system:

-

Faulty fuel pressure regulator assembly

-

Faulty engine coolant temperature sensor

-

Faulty mass air flow meter sub-assembly

-

Faulty ECM

-

Faulty fuel injector assemblies

-

Faulty throttle body with motor assembly