Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › CAMSHAFT › 2015.06–2018.06
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260525 CAMSHAFT A

1GD-FTV ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe subassembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 1 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 16206B 28.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16209 29.DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 32.REMOVE NO. 1 EGR COOLER WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 33.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 35.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 36.REMOVE NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 11201 40.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 41.SET NO. 1 CYLINDER TO TDC / COMPRESSION

a.
U169474E02
1.594,1.365 1.969,1.823 1.969,1.823 2.167,1.823 true 1.49,1.323 1.115,0.865 1.115,0.865 0.927,0.865 true 0.99,3.198 0.615,2.74 0.615,2.74 0.427,2.74 false 2.219,3.198 2.583,2.74 2.583,2.74 2.781,2.74 false 1.01,3.302 1.01,3.677 false 2.219,3.292 2.219,3.677 false 0.729,0.76 1,0.979 0.271,0.219 10 true *a 2.188,1.74 2.656,1.958 0.469,0.219 10 false *a 0.219,2.646 0.49,2.865 0.271,0.219 10 false *b 2.781,2.646 3.052,2.865 0.271,0.219 10 false *b 0.927,3.677 1.156,3.896 0.229,0.219 10 false *a 2.125,3.677 2.354,3.896 0.229,0.219 10 false *a

Align the timing mark of the crankshaft pulley and timing chain cover by rotating the crankshaft clockwise.

Text in Illustration
*a Timing Mark
*b Paint Mark


b.

Make sure that the timing mark of the camshaft timing sprocket is at the top.

HINT:

If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/ compression).



c.

Place paint marks on the No. 2 chain sub-assembly.


Hide 13566B 42.REMOVE TIMING CHAIN GUIDE

a.
A345766

Remove the bolt and timing chain guide from the cylinder head sub-assembly.


Hide 43.REMOVE CAMSHAFT

a.
A345767

Remove the oil pump relief valve plug and gasket from timing chain cover.


b.
A345768E02
1.792,0.844 2.5,0.844 true 1.74,1.719 2.448,1.719 true 2.521,0.75 2.708,0.938 0.188,0.188 10 true *a 2.479,1.625 2.667,1.813 0.188,0.188 10 true *b

Insert a pin into stopper plate hole of the No. 2 chain tensioner assembly and lock the No. 2 chain tensioner assembly.

Text in Illustration
*a Stopper Plate
*b Pin


c.
A345769E02
1.969,0.615 2.906,0.615 true 0.49,2.906 1.427,2.906 true 2.938,0.531 3.156,0.823 0.219,0.292 10 false *1 0.271,2.823 0.49,3.115 0.219,0.292 10 false *2

Hold the hexagonal portion of the camshaft with a wrench and loosen the 2 bolts from the No. 1 camshaft and No. 2 camshaft.

CAUTION:

Be careful not to damage the cylinder head sub-assembly with the wrench.


Text in Illustration
*1 No. 1 Camshaft
*2 No. 2 Camshaft


d.
A343548

Remove the 2 bolts and No. 3 camshaft bearing cap from the cylinder head sub-assembly.


e.
A345770E02
0.083,0.208 0.188,0.365 0.104,0.156 10 true 1 0.073,1.76 0.177,1.917 0.104,0.156 10 true 2 0.052,0.656 0.188,0.813 0.135,0.156 10 true 3 0.042,1.333 0.177,1.49 0.135,0.156 10 true 4 0.5,1.708 0.677,1.865 0.177,0.156 10 true 11 0.594,0.865 0.771,1.021 0.177,0.156 10 true 12 1.073,1.135 1.25,1.292 0.177,0.156 10 true 10 1.281,0.875 1.458,1.031 0.177,0.156 10 true 20 1.208,0.333 1.333,0.51 0.125,0.177 10 true 9 1.188,1.688 1.365,1.844 0.177,0.156 10 true 19 1.729,1.094 1.906,1.25 0.177,0.156 10 true 18 1.875,0.344 2.063,0.542 0.188,0.198 10 true 17 1.948,0.875 2.146,1.031 0.198,0.156 10 true 16 1.906,1.698 2.083,1.854 0.177,0.156 10 true 15 2.396,1.104 2.573,1.26 0.177,0.156 10 false 14 2.552,0.344 2.75,0.521 0.198,0.177 10 true 13 3.198,0.344 3.354,0.531 0.156,0.188 10 true 5 3.208,1.104 3.344,1.292 0.135,0.188 10 true 6 2.583,1.698 2.729,1.854 0.146,0.156 10 true 7 2.625,0.875 2.75,1.031 0.125,0.156 10 true 8

Using several steps, and remove the 20 bolt, No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps from the cylinder head sub-assembly.


f.
A345771

Raise the No. 1 camshaft and remove the bolt from the No. 1 camshaft.


g.

Raise the No. 2 camshaft and remove the bolt from the No. 2 camshaft.


h.
A345772

Remove the No. 2 camshaft from the camshaft timing sprocket.


i.
A345774

Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.


j.
A345773

Remove the No. 1 camshaft from the camshaft timing sprocket.


k.
A345775

Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.


l.
A345776

Suspend the No. 2 chain sub-assembly with a string or equivalent.

HINT:

Be careful not to drop the No. 2 chain sub-assembly inside the timing chain cover assembly.