Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2015.06–2018.06
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260522 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 82121 3.REMOVE ENGINE WIRE

Hide 12631A 12.REMOVE ENGINE COVER BRACKET

a.
A343495

Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.


Hide 16206B 17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 27148A 18.REMOVE CONNECTING WIRE

a.
A343587

Disconnect the connector from the common rail assembly.


b.

Detach the 2 clamps and remove the connecting wire from the hose bracket.


Hide 25601 19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A354080

Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


c.
A354081

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 16209 21.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A354082E01
2.823,1.771 2.823,2.104 2.823,2.104 3,2.104 true 2.854,4.167 2.854,3.833 2.854,3.833 3.031,3.833 true 1.708,0.74 1.115,0.229 1.115,0.229 0.938,0.229 true 1.427,1.615 0.938,2.052 0.938,2.052 0.75,2.052 true 1.708,3.24 1.115,2.729 1.115,2.729 0.938,2.729 true 2.667,0.458 2.552,0.125 2.552,0.125 2.375,0.125 true 2.729,3 2.573,2.604 2.573,2.604 2.396,2.604 true 3.031,2.01 3.26,2.208 0.229,0.198 10 true *1 0.719,0.135 0.906,0.292 0.188,0.156 10 false *2 2.156,0.031 2.344,0.219 0.188,0.188 10 true *3 0.542,1.958 0.729,2.115 0.188,0.156 10 false *4 0.052,0.021 0.302,0.208 0.25,0.188 12 false *A 0.052,2.469 0.302,2.656 0.25,0.188 12 false *B 3.063,3.75 3.25,3.906 0.188,0.156 10 true *1 0.719,2.635 0.906,2.792 0.188,0.156 10 false *2 2.177,2.51 2.365,2.667 0.188,0.156 10 true *3

Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.

Text in Illustration
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose
*4 No. 11 Water By-pass Hose


b.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


c.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


d.

for Cold Area Specification Vehicles:

Detach the clamp and disconnect the No. 11 water by-pass hose from the No. 2 fuel pipe.


e.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.


Hide 25800 22.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 23.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23812D 24.REMOVE NO. 2 FUEL PIPE

a.
A343499

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


b.

Remove the bolt and No. 2 fuel pipe from the manifold stay.


Hide 22803 27.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23770 33.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 35.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 37.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A354083

for LHD:

Remove the 3 bolts and 3 wiring harness clamp brackets from the cylinder head cover sub-assembly.


b.
A354084

for RHD:

Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.


Hide 23701 38.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 39.REMOVE COMMON RAIL ASSEMBLY

Hide 19871 40.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 42.REMOVE HOSE BRACKET

a.
A343501

Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.


Hide 23300 44.REMOVE FUEL FILTER ASSEMBLY

a.
A347297

Remove the 2 nuts and fuel filter assembly from the cylinder block sub-assembly.


Hide 16025 45.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343503

Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.


Hide 88431 46.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A354085

Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 12261 48.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 12229 49.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 16282 50.REMOVE NO. 5 WATER BY-PASS HOSE

a.
A347299

Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.


b.

Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.


Hide 16281 51.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
A347300

Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.


Hide 25051 59.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 12361 60.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A354086

Disconnect the No. 3 vacuum transmitting hose sub-assembly from the front engine mounting insulator RH.


b.

Remove the nut and front engine mounting insulator RH from the front No. 1 engine mounting bracket RH.


Hide 16268 62.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A354087E01
0.127,0.043 0.390,0.232 0.262,0.189 12 *A 0.127,2.483 0.391,2.679 0.264,0.195 12 *B

Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.

Text in Illustration
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


Hide 87101 64.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.
A354088

Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly from the cylinder block sub-assembly and timing chain cover sub-assembly.


Hide 17293 65.REMOVE TURBOCHARGER STAY

A353383

a.

Remove the 3 bolts, nut and the turbocharger stay.


Hide 17201 68.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A352795

Remove the 3 nuts and turbocharger sub-assembly.


b.

Remove the gasket from the exhaust manifold.


Hide 16207 70.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343506

Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.


b.

Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.


Hide 16304 71.REMOVE WATER OUTLET SUB-ASSEMBLY

a.
A347303E01
0.048,0.035 0.310,0.211 0.262,0.176 12 *A 0.048,2.436 0.308,2.613 0.259,0.176 12 *B

Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.

Text in Illustration
*A w/ DPF
*B w/o DPF


b.

Remove the gasket from the timing chain cover sub-assembly.


Hide 16603 72.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 73.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 25804A 74.REMOVE VACUUM SWITCHING VALVE SUB-ASSEMBLY (for Engine Mounting)

Hide 25706 75.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A456453

Disconnect the No. 1 vacuum transmitting hose sub-assembly from the vacuum pump assembly.


b.
A457925

Disconnect the No. 2 vacuum transmitting hose sub-assembly from the No. 3 vacuum transmitting pipe sub-assembly.


c.

Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.


Hide 25707 76.REMOVE NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A354091

Remove the 2 bolts and No. 2 vacuum transmitting pipe sub-assembly from the cylinder block sub-assembly and oil pan sub-assembly.


Hide 25708 77.REMOVE NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A354092

Disconnect the No. 4 vacuum transmitting hose sub-assembly from the No. 3 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 bolts and No. 3 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly and cylinder block sub-assembly.


Hide 25709E 78.REMOVE NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A354093

Remove the bolt and No. 4 vacuum transmitting pipe sub-assembly from the cylinder block sub-assembly.


Hide 88451B 79.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16575C 82.REMOVE NO. 1 WATER HOSE CLAMP BRACKET

a.
A347304

Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.