Home › Engine / Hybrid System › 1GD-FTV (LUBRICATION) › OIL PUMP › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053690 1GD-FTV LUBRICATION _0260709 OIL PUMP A

1GD-FTV LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.



PROCEDURE

Hide 12633 2.REMOVE NO. 3 ENGINE COVER BRACKET

a.
A339756

Remove the 2 bolts and No. 3 engine cover bracket from the No. 2 engine cover bracket and engine cover bracket.


Hide 4.REMOVE ENGINE WIRE

Hide 16206B 18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16209 22.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25800 23.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 22803 28.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23770 35.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 27148A 37.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 39.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 82715 40.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23701 41.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 88431 43.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 12261 44.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 12229 45.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 25051 55.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 87101 59.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

Hide 16207 64.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16603 68.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A339577

Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.


Hide 16620 69.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A339579

Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


Hide 88451B 70.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16575C 73.REMOVE NO. 1 WATER HOSE CLAMP BRACKET

Hide 11201 79.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A339580

Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.

Text in Illustration
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat


b.
A339581E02
2.5,0.281 2.427,0.281 2.427,0.281 2.25,0.552 true 1.042,0.323 0.958,0.323 0.958,0.323 0.781,0.594 true 1.177,1.208 1.094,1.208 1.094,1.208 0.885,1.375 true 0.313,1.802 0.396,1.802 0.396,1.802 0.708,1.229 true 2.563,0.188 2.802,0.385 0.24,0.198 10 false *1 1.104,0.24 1.354,0.427 0.25,0.188 10 false *3 1.229,1.135 1.479,1.323 0.25,0.188 10 true *3 0.115,1.708 0.354,1.885 0.24,0.177 10 false *2

Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.

Text in Illustration
*1 Cylinder Head Cover Gasket
*2 No. 2 Cylinder Head Cover Gasket
*3 Camshaft Bearing Cap Oil Hole Gasket


Hide 12102A 81.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A339699

Remove the 2 nuts and 11 bolts.

Text in Illustration
V100135

Bolt
V100136

Nut


b.
A120816

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly, cut off the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.

·

Be careful not to damage the oil pan sub-assembly flange.




Hide 12101 82.REMOVE OIL PAN SUB-ASSEMBLY

a.
A339700

Remove the 2 nuts and 23 bolts.

Text in Illustration
V100135

Bolt
V100136

Nut


b.
A120816

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.

·

Be careful not to damage the cylinder block sub-assembly flange.




Hide 11324 85.REMOVE TIMING CHAIN COVER PLATE

Hide 11302 88.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A339584

Remove the 20 bolts from the timing chain cover sub-assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.

A339585E02
6.583,0.198 6.458,0.198 6.458,0.198 6.177,0.677 true 6.188,2.427 6.063,2.427 6.063,2.427 5.615,1.927 true 0.594,1.281 0.719,1.281 0.719,1.281 0.99,0.656 true 6.635,0.104 6.896,0.292 0.26,0.188 10 false *a 6.25,2.333 6.49,2.521 0.24,0.188 10 false *a 0.375,1.177 0.635,1.375 0.26,0.198 10 false *a

Text in Illustration
*a Protective Tape - -

NOTICE:

Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.



c.
A339592

Remove the timing chain case gasket from the timing chain case assembly.


Hide 11303A 89.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A339586E02
2.469,0.24 2.302,0.24 2.302,0.24 1.479,0.938 true 0.646,1.219 1.271,1.219 true 2.542,0.156 2.792,0.344 0.25,0.188 10 false *a 0.406,1.125 0.656,1.323 0.25,0.198 10 false *b

Using a screwdriver and wooden block, pull out the front crankshaft oil seal.

Text in Illustration
*a Protective Tape
*b Wooden Block

NOTICE:

Do not damage the surface of the front crankshaft oil seal press fit hole.



Hide 90.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

a.
A339596

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.3 mm (0.000787 to 0.0118 in.)


Maximum gear backlash:

0.42 mm (0.0165 in.)


If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.


Hide 13519 91.REMOVE OIL PUMP DRIVE GEAR

a.
A339595

Remove the oil pump drive gear from the crankshaft.


Hide 13560A 92.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 11991A 93.REMOVE NO.1 BALANCE SHAFT THRUST PLATE

Hide 94.REMOVE BALANCE SHAFT TIMING SPROCKET, BALANCE SHAFT GEAR SUB-ASSEMBLY AND NO. 3 CHAIN SUB-ASSEMBLY

Hide 13540 100.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13506 103.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 11310 105.REMOVE TIMING CHAIN CASE ASSEMBLY

a.
A339590

Remove the 15 bolts from the timing chain case assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.

A339591E01
6.792,0.135 6.646,0.135 6.646,0.135 6.375,0.479 true 6.448,2.448 6.302,2.448 6.302,2.448 5.823,2.083 true 0.615,0.76 0.76,0.76 0.76,0.76 1.156,1.219 true 6.854,0.031 7.104,0.208 0.25,0.177 10 false *a 6.51,2.354 6.771,2.542 0.26,0.188 10 false *a 0.385,0.656 0.656,0.865 0.271,0.208 10 false *a

Text in Illustration
*a Protective Tape - -

NOTICE:

Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.



c.
A339593

Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.


d.
A388469

Remove the gasket from the timing chain case assembly.