Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › MONOLITHIC CONVERTER (w/ DPF) › 2015.06–2018.06
RM27T0E _51 Engine / Hybrid System _053675 1GD-FTV EMISSION CONTROL _0260626 MONOLITHIC CONVERTER A

1GD-FTV EMISSION CONTROL  MONOLITHIC CONVERTER  INSTALLATION  


PROCEDURE

Hide 25051 1.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.

Set a new gasket and the exhaust manifold converter sub-assembly to the turbocharger sub-assembly.


b.

Temporarily install the exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the 3 bolts.


c.
A344468E02
2.594,0.615 2.594,0.365 2.594,0.365 2.781,0.365 false 2.688,1.365 2.688,1.698 false 0.677,1.875 0.958,2.063 0.281,0.188 10 false 90° 2.802,0.271 3.01,0.479 0.208,0.208 10 false *1 2.313,1.104 2.521,1.313 0.208,0.208 10 false *2 2.865,1.281 3.073,1.49 0.208,0.208 10 false *3 2.615,1.708 2.823,1.875 0.208,0.167 10 false *4

Install a new exhaust pipe clamp to the exhaust manifold converter sub-assembly with a new nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

Text in Illustration
*1 Exhaust Pipe Clamp
*2 Exhaust Manifold Converter
*3 Turbocharger Sub-assembly
*4 Gasket


d.

Tighten the 3 bolts and install the exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17118 2.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY

a.

Install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the bolt and 2 new nuts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17271 3.INSTALL NO. 1 TURBO INSULATOR

a.

Install the No. 1 turbo insulator to the exhaust manifold and turbocharger sub-assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12631A 7.INSTALL ENGINE COVER BRACKET

a.

Install the engine cover bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 clamps and connect the engine wire to the cylinder head sub-assembly.


Hide 17578B 8.INSTALL PIPE CLAMP

a.

Install the pipe clamp to the engine cover bracket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25734 9.TEMPORARILY INSTALL NO. 2 VACUUM PIPE

a.

Install a new clamp to the pipe clamp.


b.

Temporarily install the No. 2 vacuum pipe to the exhaust manifold converter sub-assembly.


Hide 25733A 10.TEMPORARILY INSTALL NO. 1 VACUUM PIPE

a.

Temporarily install the No. 1 vacuum pipe to the exhaust manifold converter sub-assembly.


b.

Install a new clamp to the No. 1 vacuum pipe and No. 2 vacuum pipe with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 25734 11.TIGHTEN NO. 2 VACUUM PIPE

a.
A329093E01
1.759,0.583 1.944,0.738 0.185,0.155 10 *a

Using a 17 mm union nut wrench, tighten the No. 2 vacuum pipe.

Torque:

Specified tightening torque

48 N*m {489 kgf*cm, 35 ft.*lbf}


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 43 N*m (437 kgf*cm, 32 ft.*lbf)



Text in Illustration
*a Torque Wrench Fulcrum Length


Hide 25733A 12.TIGHTEN NO. 1 VACUUM PIPE

a.
A329093E01
1.759,0.583 1.944,0.738 0.185,0.155 10 *a

Using a 17 mm union nut wrench, tighten the No. 1 vacuum pipe.

Torque:

Specified tightening torque

48 N*m {489 kgf*cm, 35 ft.*lbf}


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 43 N*m (437 kgf*cm, 32 ft.*lbf)



Text in Illustration
*a Torque Wrench Fulcrum Length


Hide 17801 17.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 18.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

Hide 53736B 19.INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL RH

Hide 17168 20.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17410 21.INSTALL FRONT EXHAUST PIPE ASSEMBLY