1.INSTALL STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Using an E10 "TORX" socket wrench, install the 3 stud bolts at the positions shown in the illustration.
Using an E8 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.
Using an E5 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.
17275
2.INSTALL COMPRESSOR OUTLET ELBOW
Install the hose clamp with the bolt.
Install a new gasket.
Install a new gasket and the compressor outlet elbow with the 2 nuts.
17274
3.INSTALL COMPRESSOR INLET ELBOW
Install a new gasket.
Using an E8 "TORX" socket wrench, install a new gasket and the compressor inlet elbow with the stud bolt.
Install the compressor inlet elbow to the turbocharger sub-assembly with the 2 nuts.
Install the compressor inlet elbow stay with the 2 bolts.
16027
4.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
Install a new gasket.
Temporarily install the turbo water pipe sub-assembly with the bolt and 2 nuts.
Tighten the bolt and 2 nuts.
Connect the No. 1 turbo water hose and No. 2 turbo water hose to the No. 1 turbo water pipe sub-assembly and slide the 2 hose clips to secure the hoses.
15407
5.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY
| *a | NG |
| *b | OK |
Install a new gasket as shown in the illustration.
Do not install the gasket upside down.
Temporarily install the turbo oil inlet pipe subassembly with the 2 nuts.
17141
6.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.
Install a new gasket (No. 1 EGR pipe sub-assembly side) to the exhaust manifold.
Install a new gasket to the turbocharger sub-assembly.
Temporarily install the turbocharger sub-assembly with 3 new nuts.
| *1 | Collar |
|
Engine Side |
Install a new gasket (cylinder head side), and then temporarily install the exhaust manifold with 8 new nuts, 8 new collars and 8 new washers.
Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.
Install a new gasket on the union bolt side to turbo oil inlet pipe sub-assembly.
Temporarily install the union bolt.
15474
7.INSTALL TURBO OIL OUTLET PIPE
Install a new gasket to the turbo oil outlet pipe.
The claws of the gasket must face the turbo oil outlet pipe.
Install the turbo oil outlet pipe with the 2 bolts.
Connect the turbo oil outlet hose to the turbo oil outlet pipe, turbo oil inlet pipe and slide the 2 hose clips to secure the hoses.
17293
8.TEMPORARILY INSTALL TURBOCHARGER STAY
for Type B:
Temporarily install the turbocharger stay to the turbocharger sub-assembly, with 3 bolts and nut.
for Type A:
Temporarily install the turbocharger stay and stad bolt.
Using an E8 "TORX" socket wrench, tighten the stud bolt.
Temporarily install the 3 bolts and nut.
17141
9.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
Tighten the exhaust manifold with turbocharger sub-assembly, to the cylinder head sub-assembly with 8 nuts.
Tighten the nuts in the order shown in the illustration.
Tighten the turbocharger sub-assembly, to the exhaust manifold with the 3 nuts.
Tighten the 2 nuts and then union bolt of the turbo oil inlet pipe sub-assembly.
If the connecting part of the union bolt gasket is cracked, remove the connecting part.
17293
10.TIGHTEN TURBOCHARGER STAY
Tighten the 3 bolts and nut of the turbocharger stay in the order shown in the illustration.
87101
11.INSTALL VISCOUS HEATER NO.1 BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)
|
No. 1 Viscous Heater Bracket Bolt |
|
No. 4 Engine Harness Bolt |
Temporarily install the No. 1 viscous heater bracket sub-assembly with 4 bolts.
Tighten the 4 bolts and of the No. 1 viscous heater bracket sub-assembly in the order shown in the illustration.
Connect the No. 4 engine harness with the bolt.
Connect the wire harness.
12.INSTALL OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMPBRACKET
Connect the wire harness clamp bracket with the bolt.
for Automatic Transmission:
Connect the oil cooler tube bracket with the bolt.
25601
13.CONNECT NO. 1 EGR PIPE SUB-ASSEMBLY
Connect the No. 1 EGR pipe sub-assembly with 2 new nuts.
16284
14.CONNECT TURBO WATER HOSE
Connect the No. 1 turbo water hose and No. 2 turbo water hose to the water outlet sub-assembly, engine water pump assembly and slide the 2 hose clips to secure the hoses.
The turbocharger sub-assembly may be damaged if the No. 1 turbo water hose and No. 2 turbo water hose are connected to the wrong locations.
16268
15.CONNECT NO. 1 WATER BY-PASS PIPE
12203
16.INSTALL PCV HOSE (except Cold Area Specification Vehicles)
Attach the clamp and install the PCV hose.
Slide the 2 hose clips to secure the hoses.
12203
17.INSTALL PCV PIPE (for Cold Area Specification Vehicles)
Connect the PCV pipe to the compressor inlet elbow, cylinder head cover sub-assembly and slide the 2 hose clips to secure the hoses.
Install the PCV pipe with the bolt to the compressor inlet elbow.
Connect the No. 19 water by-pass hose to the compressor inlet elbow and slide the hose clip to secure the hoses.
Install the No. 20 water by-pass hose to the PCV pipe and No. 1 water by-pass pipe, and slide the 2 hose clips to secure the hoses.
16279
18.INSTALL NO. 3 WATER BY-PASS PIPE
Connect the 2 water hoses to the oil cooler assembly and No. 2 water by-pass pipe, and slide the 2 hose clips to secure the hoses.
Install the No. 3 water by-pass pipe with the bolt.
for Cold Area Specification Vehicles:
Install the water hose to the compressor inlet elbow and No. 3 water by-pass pipe, and slide the 2 hose clips to secure the hoses.
87209B
19.INSTALL WATER HOSE SUB-ASSEMBLY B (w/ Viscous Heater)
87120G
20.INSTALL VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY
21.INSTALL AIR CLEANER CASE
Install the air cleaner case sub-assembly with the 3 bolts.
for Cold Area Specification Vehicles:
Connect the wire harness clamps.
17801
22.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner case.
17705
23.CONNECT AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE
Attach the 4 clips to install the air cleaner cap sub-assembly with air cleaner hose.
Tighten the hose clamp.
Connect the mass air flow meter connector and attach the 2 wire harness clamps.
16711
24.INSTALL FAN SHROUD
16470
25.INSTALL RADIATOR RESERVOIR ASSEMBLY
16571C
26.INSTALL NO. 1 RADIATOR HOSE
44306
27.INSTALL VANE PUMP OIL RESERVOIR SUB-ASSEMBLY
17342F
28.INSTALL NO. 2 INTERCOOLER AIR HOSE
17341K
29.INSTALL INTERCOOLER AIR HOSE
25051
30.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
31.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
33.ADD ENGINE COOLANT
34.INSPECT FOR OIL LEAK
35.INSPECT ENGINE OIL LEVEL
36.INSPECT FOR COOLANT LEAK
37.INSPECT FOR EXHAUST GAS LEAK